Related Manuals for Panasonic PAN1760A
Summary of Contents for Panasonic PAN1760A
- Page 1 PAN1760A Bluetooth Low Energy Module Product Specification Rev. 1.1 Wireless Modules...
- Page 2 PAN1760A Bluetooth Module Overview Bluetooth • The PAN1760A is Panasonic’s next generation GAP central and peripheral support for LE Bluetooth module with the industry’s lowest power • GATT, SMP, and SDB support for LE Bluetooth Low Energy SoC. •...
- Page 3 By purchase of any of the products described in this document the customer accepts the document's validity and declares their agreement and understanding of its contents and recommendations. Panasonic reserves the right to make changes as required at any time without notification. Please consult the most recently issued Product Specification before initiating or completing a design.
-
Page 4: Table Of Contents
PAN1760A Bluetooth Module Table of Contents About This Document ......................... 5 Purpose and Audience ......................5 Revision History ......................... 5 Use of Symbols ......................... 5 Related Documents ........................5 Overview .............................. 6 Block Diagram ........................... 7 Pin Configuration ........................8 UART Interface ........................ -
Page 5: About This Document
1.1 Purpose and Audience This Product Specification provides details on the functional, operational, and electrical characteristics of the Panasonic PAN1760A module. It is intended for hardware design, application, and Original Equipment Manufacturers (OEM) engineers. The product is referred to as “the PAN1760A” or “the module” within this document. -
Page 6: Overview
IoT, medical, and industrial applications without compromising battery life. Mandatory and optional Bluetooth 4.2 features are supported. The PAN1760A can either be operated in AT-Command or Host mode for very simple integration of Bluetooth connectivity into existing products, or in Stand-Alone mode. -
Page 7: Block Diagram
PAN1760A Bluetooth Module 2 Overview 2.1 Block Diagram PAN1760A Vcc 3.3 V Slow Clock Bluetooth 4.2 Module 32 KHz UART Crystal 26 MHz GPIOs Chip Antenna DC-DC Toshiba Conversion Host Wake up TC35678 Wake up Flash 256 kB Reset Total capacitor value: 2.4 µF +/-10 %... -
Page 8: Pin Configuration
PAN1760A Bluetooth Module 2 Overview 2.2 Pin Configuration Pin Assignment Top View 15.6 mm Pin Functions Pin Name Pin Type Description Ground Pin Connect to ground GPIO3 Digital I/O RESET Digital Input Reset, active low Not connected Power Analog/digital power supply connection... - Page 9 PAN1760A Bluetooth Module 2 Overview Pin Name Pin Type Description Not connected, leave open Not connected, leave open GPIO7 Digital I/O GPIO8 Digital I/O GPIO25 Digital I/O Not connected, leave open Not connected, leave open Not connected, leave open...
-
Page 10: Uart Interface
PAN1760A Bluetooth Module 2 Overview Pin Name Pin Type Description Not connected, leave open Ground Pin Connect to ground Ground Pin Connect to ground Ground Pin Connect to ground Not connected, leave open Not connected, leave open Not connected, leave open... -
Page 11: Detailed Description
PAN1760A Bluetooth Module 3 Detailed Description 3 Detailed Description 3.1 Dimensions All dimensions are in millimeters. Item Dimension Tolerance Remark 1 Width 8.70 ± 0.20 2 Length 15.60 ± 0.20 3 Height 1.80 ± 0.20 With case Product Specification Rev. 1.1... -
Page 12: Footprint
PAN1760A Bluetooth Module 3 Detailed Description 3.2 Footprint The outer dimensions have a tolerance of 0.2 mm. Top View 15.6 mm Product Specification Rev. 1.1 Page 12... -
Page 13: Packaging
PAN1760A Bluetooth Module 3 Detailed Description 3.3 Packaging The product is a mass production status product and will be delivered in the package described below. 3.3.1 Tape Dimensions 3.3.2 Packing in Tape Direction of unreeling (for customer) Top cover tape more... - Page 14 PAN1760A Bluetooth Module 3 Detailed Description 3.3.3 Component Direction 3.3.4 Reel Dimension Product Specification Rev. 1.1 Page 14...
- Page 15 PAN1760A Bluetooth Module 3 Detailed Description 3.3.5 Package Label Example (1T) Lot code (1P) Customer order number, if applicable (2P) Order number (9D) Date code Quantity (HW/SW) Hardware/software version 3.3.6 Total Package Product Specification Rev. 1.1 Page 15...
-
Page 16: Case Marking
PAN1760A Bluetooth Module 3 Detailed Description 3.4 Case Marking Example MIC ID Brand name Hardware/software version Order number FCC ID Lot code Engineering Sample marking, if applicable Marking for Pin 1 2D barcode, for internal usage only Product Specification Rev. 1.1... -
Page 17: Specification
PAN1760A Bluetooth Module 4 Specification 4 Specification All specifications are over temperature and process, unless indicated otherwise. 4.1 Default Test Conditions Temperature: 25 ± 10 °C Humidity: 40 to 85 % RH Supply Voltage: 3.3 V 4.2 Absolute Maximum Ratings The maximum ratings may not be exceeded under any circumstances, not even momentarily or individually, as permanent damage to the module may result. -
Page 18: Recommended Operating Conditions
PAN1760A Bluetooth Module 4 Specification 4.3 Recommended Operating Conditions The maximum ratings may not be exceeded under any circumstances, not even momentarily or individually, as permanent damage to the module may result. Symbol Parameter Condition Min. Typ. Max. Units Ambient °C... -
Page 19: Bluetooth
PAN1760A Bluetooth Module 4 Specification 4.5 Bluetooth Parameter Condition Min. Typ. Max. Units Operation 2 402 2 480 frequency range Channel spacing Output Power Maximum setting, measured at dual ended 50 Ohm. Sensitivity Symbol Parameter Condition Min. Typ. Max. -
Page 20: Recommended Soldering Profile
PAN1760A Bluetooth Module 4 Specification 4.7 Recommended Soldering Profile • Reflow permissible cycle: 2 • Opposite side reflow is prohibited due to module weight • More than 75 percent of the soldering area shall be coated by solder •... -
Page 21: Cautions
PAN1760A Bluetooth Module 5 Cautions 5 Cautions Failure to follow the guidelines set forth in this document may result in degrading of the product’s functions and damage to the product. 5.1 Design Notes 1. Follow the conditions written in this specification, especially the control signals of this module. -
Page 22: Usage Condition Notes
PAN1760A Bluetooth Module 5 Cautions 5.3 Usage Condition Notes 1. Take measures to protect the unit against static electricity. If pulses or other transient loads (a large load applied in a short time) are applied to the products, check and evaluate their operation befor assembly on the final products. -
Page 23: Other Cautions
Panasonic customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Panasonic Industrial Devices Europe GmbH for any damages resulting. -
Page 24: Regulatory And Certification Information
6.1.2 Caution The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Panasonic Industrial Devices Europe GmbH may void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. - Page 25 Panasonic FCC identifier for this product as well as the FCC Notice above. The FCC identifier is FCC ID: T7V1760A. This FCC identifier is valid for the PAN1760A. The end product must in any case be labelled on the exterior with: "Contains FCC ID: T7V1760A"...
-
Page 26: Innovation, Science, And Economic Development (Ised) For Canada
6.2 Innovation, Science, and Economic Development (ISED) for Canada English The PAN1760A is licensed to meet the regulatory requirements of Industry Canada (IC). License ID: IC: 216Q-1760A Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any regulatory questions and ensure compliance for SAR and/or RF exposure limits. - Page 27 PAN1760A Bluetooth Module 6 Regulatory and Certification Information French PAN1760A est garanti conforme aux dispositions règlementaires d’Industry Canada (IC). License: IC: 216Q-1760A Il est recommandé aux fabricants d’appareils fixes, mobiles ou portables de consulter la réglementation en vigueur et de vérifier la conformité de leurs produits relativement aux limites d’exposition aux rayonnements radiofréquence ainsi qu’au débit d’absorption spécifique...
-
Page 28: Japanese Radio Law Compliance
The OEM must ensure that IC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic IC identifier for this product as well as the IC Notice above. The IC identifier is: IC: 216Q-1760A ... -
Page 29: European Conformity According To Red (2014/53/Eu)
As a result of the conformity assessment procedure described in the 2014/53/EU Directive, the end customer equipment should be labelled as follows: PAN1760A in the specified reference design can be used in all countries of the European Economic Area (Member States of the EU, European Free Trade Association States [Iceland, Liechtenstein, Norway]), Monaco, San Marino, Andorra and Turkey. -
Page 30: Appendix
PAN1760A Bluetooth Module 7 Appendix 7 Appendix 7.1 Ordering Information Variants and Versions Order Number Brand Name Description ENW89847A3KF PAN1760A Bluetooth Low Energy Module 1 500 Abbreviation for Minimum Order Quantity (MOQ). The default MOQ for mass production is 1 500 pieces, fewer only on customer demand. -
Page 31: Contact Details
For Panasonic Sales assistance in the EU, visit https://eu.industrial.panasonic.com/about-us/contact-us Email: wireless@eu.panasonic.com For Panasonic Sales assistance in North America, visit the Panasonic Sales & Support Tool to find assistance near you at https://na.industrial.panasonic.com/distributors Please visit the Panasonic Wireless Technical Forum to submit a question at https://forum.na.industrial.panasonic.com...