Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hinkley Tier
Summary of Contents for Hinkley Tier
- Page 1 54" TIER ™ INDOOR / OUTDOOR LED FAN CEILING FAN INSTRUCTION MANUAL...
- Page 2 SO WE’RE HERE IF YOU HAVE A QUESTION, NEED SOME HELP OR WANT TO CHAT ABOUT OUR PRODUCTS. SEND SUGGESTIONS OUR WAY TOO—WE’RE ALWAYS LOOKING TO MAKE YOUR EXPERIENCE WITH HINKLEY A POSITIVE ONE. > SERVICE@HINKLEY.COM > 800.HINKLEY > LET’S SEE THAT HINKLEY STYLE @HINKLEY...
-
Page 3: Table Of Contents
INSTALLING THE HANGING BRACKET TROUBLESHOOTING HANGING THE FAN ENERGY GUIDE ELECTRICAL CONNECTIONS SPECIFICATIONS FINISHING THE INSTALLATION SMART BY BOND BLADE ATTACHMENT WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout. ©2019 Hinkley Lighting, Inc. | hinkley.com |... - Page 4 The fan can be made to work immediately after installation - the bearings are adequately charged with grease so that, under normal conditions, further lubrication should not be necessary for the life of the fan. To operate the reverse function on this fan, press the reverse button while the fan is running. | hinkley.com...
-
Page 5: Important Safety Precautions
These factors must be supplied by the person(s) installing, caring for and operating the unit. TOOLS & MATERIALS REQUIRED • PHILLIPS SCREWDRIVER • FLAT SCREWDRIVER • WRENCH OR PLIERS • WIRE CUTTER • STEPLADDER • WIRING SUPPLIES AS REQUIRED BY ELECTRICAL CODE ©2019 Hinkley Lighting, Inc. | hinkley.com |... -
Page 6: Unpacking Your Fan
Remove all parts and hardware. Do not lay motor housing on its side, or the decorative housing may shift, be bent or damaged. • Examine all parts. You should have the following: TIER PACKAGE CONTENT Blade Set of 5 Blade support plates... -
Page 7: Preparation
35 pounds. Attach hanging bracket to outlet box using screws provided with the outlet box. Flat Washer Spring Washer Outlet Box Screw Fig. 1 ©2019 Hinkley Lighting, Inc. | hinkley.com |... -
Page 8: Hanging The Fan
Tighten security set screws against downrod using a large flat blade screwdriver to ensure a tight fit against downrod. Downrod Tighten nuts against mounting collar. Security Screws Mounting Collar Downrod Pin Cotter Pin Top of Fan Body Fig. 2 | hinkley.com... - Page 9 (Fig. 4) Trim Ring Yoke Cover NOTE: 6 feet of lead wire is supplied on the fan for use with longer downrods. Top of Fan Body Fig. 3 Registration slot Fig. 4 ©2019 Hinkley Lighting, Inc. | hinkley.com...
-
Page 10: Electrical Connections
Insert the receiver into the ceiling mounting bracket with the flat side of the receiver facing the ceiling. (Fig. 2) For best performance, make sure the Black Antenna, on the end of the receiver, remains extended and not tangled with any of the electrical wires. Receiver Fig. 2 hinkley.com... - Page 11 (Fig. 3) Note: Fan must be installed at a maximum distance of 30 feet from the remote transmitter for optimal signal transmission between the transmitter and the fan's receiving unit. Fig. 3 ©2019 Hinkley Lighting, Inc. | hinkley.com...
-
Page 12: Finishing The Installation
Trim Ring WARNING: Make sure the hook on the hanging bracket properly sits in the groove in the hanger ball before attaching the canopy to the bracket by turning the housing until it drops into place. | hinkley.com... -
Page 13: Blade Attachment
Secure by tightening the 2 screws previously loosened and the one previously removed. Light Wires Mounting Hub (bottom of motor) Mounting plate Screws Fig. 1 ©2019 Hinkley Lighting, Inc. | hinkley.com... -
Page 14: Installing The Light Kit And Glass Shade
Raise the glass shade against the LED light kit and turn clockwise until snug, DO NOT OVERTIGHTEN. Light Kit Restore power and your light kit is ready for operation. Screws Glass shade Fig. 2 | hinkley.com... -
Page 15: Installing The Wall Transmitter
Install the wall transmitter on the existing wall outlet box using the screws provided. Attached the wall plate with the mounting screws to finish the installation. (Fig. 2) Fig. 1 Transmitter Decorative Wall Plate Fig. 2 ©2019 Hinkley Lighting, Inc. | hinkley.com |... -
Page 16: Operation
Range of the transmitter is approximately 25 ft. A new alkaline battery will typically give range of 35 ft. or more. NOTE: If power is lost to the fan receiver, the memory will be lost and all settings will return to the default. Fig. 2 | hinkley.com... - Page 17 An UPWARD airflow moves warmer air off the ceiling area as shown in Figure 4. This allows you to set your heating unit on a cooler setting without affecting your comfort. SUMMER MODE WINTER MODE (COUNTERCLOCKWISE DIRECTION) (CLOCKWISE DIRECTION) Fig. 3 Fig. 4 ©2019 Hinkley Lighting, Inc. | hinkley.com...
-
Page 18: Care And Cleaning
If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight and possibly result in smoother operation. Check to assure all dowrods to motor hardware and/or hanger ball are tight. Make sure ceiling box is secure. | hinkley.com... -
Page 19: Energy Guide
SMART BY BOND HINKLEY SMART FAN OPTIONS: In addition to the included wall control, you can control your Hinkley fan through the Bond app. • To use the app, download it for free from the App Store or Google Play. - Page 20 HINKLEY IS PROUD TO PROVIDE YOU WITH CEILING FAN PRODUCTS THAT ENHANCE YOUR SPACE WITH COMFORT, PURPOSE AND STYLE. AS A FAMILY COMPANY, WE ARE COMMITTED TO DESIGN, PERFORMANCE AND QUALITY, AND WHAT’S IMPORTANT TO YOU IS PARAMOUNT TO US.
- Page 21 GLOBAL HEADQUARTERS 33000 Pin Oak Parkway | Avon Lake, Ohio 44012 T (440) 653 5500 | F (440) 653 5555 | hinkley.com...