Subscribe to Our Youtube Channel
Related Manuals for EPS EPS-16
Summary of Contents for EPS EPS-16
- Page 1 USER MANUAL EPS-16 EPS-32-V1 & EPS-32-V2 EDGE POWER SOLUTIONS 56VDC SERIES USER MANUAL VERSION 7 05/2020...
- Page 2 In the interest of continued product development, Edge Power Solutions reserves the right to make improvements in this document and the products it describes at any time, without notice or obligation. Edge Power Solutions EPS-32-V1 / EPS-32-V2 / EPS-16 Installation Manual Revision 7.0 05102020...
-
Page 3: Table Of Contents
Connection to DC power source (Rack Mount)…………….……………………….. Connection to DC power source (Wall Mount)…….……….……………………….. • SECTION 3: Optional Integrated Fiber Optic Splitter Safety Precautions………………………………………………………………………………. • • Source Signal Connection(s)………………………………………………………………… • Output Connections…………………………………………………………………………….. Edge Power Solutions EPS-32-V1 / EPS-32-V2 / EPS-16 Installation Manual Revision 7.0 05102020... -
Page 4: Introduction
1.1 Quick Installation Checklist • The following steps are recommended to quickly install the EPS-RM-1x(xx)-100W-(s) Power Supply Unit for use. a) Attach Rack Mount Brackets to the Power Supply Unit (Rack mount unit) b) Mount the power supply unit in rack or wall location Connect Safety Earth Ground connection to approved ground buss d) Connect devices to output connections using properly sized wire. -
Page 5: Model Eps-32-V1
(32) +56VDC Outputs (12AWG -24AWG) – (Up to 98W per output) a) SEE NOTE 1 / PAGE 1 • (16) Resettable 1.75A Breaker (1 per output) Optional 1x16 Passive Fiber Optic Splitter • PAGE 2 Edge Power Solutions EPS-32-V1 / EPS-32-V2 / EPS-16 Installation Manual Revision 7.0 05102020... -
Page 6: Section 2: Installation
(2) Rack Mounting Ears 2.2 Additional Required Items: • Small Tip Flat Head Screwdriver Phillips Head Screwdriver • • Appropriately sized ground wire • Power Meter PAGE 3 Edge Power Solutions EPS-32-V1 / EPS-32-V2 / EPS-16 Installation Manual Revision 7.0 05102020... -
Page 7: Safety Precautions
Always disconnect the power supply cord(s) before servicing to avoid electrical shock. For products with 2 input power cords, both must be disconnected before servicing. WARNING: Earth Ground connection is essential before powering on device. PAGE 4 Edge Power Solutions EPS-32-V1 / EPS-32-V2 / EPS-16 Installation Manual Revision 7.0 05102020... -
Page 8: Mounting Pdu
2.5 Chassis Grounding • Attach properly sized ground wire as required and secure to an approved earth ground prior to making any other connections to this device. PAGE 5 Edge Power Solutions EPS-32-V1 / EPS-32-V2 / EPS-16 Installation Manual Revision 7.0 05102020... -
Page 9: Installing Phoenix Connectors
Fill in all unused positions with 2 position connectors to avoid leaving exposed pins If Connector removal is required use care to avoid bending the pins of the receiving connector. • PAGE 6 Edge Power Solutions EPS-32-V1 / EPS-32-V2 / EPS-16 Installation Manual Revision 7.0 05102020... -
Page 10: Connecting To Ac Power Source
Turn on CB1 & CB2 (EPS-32-V1) • The power switch(es) will light up in off position to indicate the AC power source outlet is properly grounded. PAGE 7 Edge Power Solutions EPS-32-V1 / EPS-32-V2 / EPS-16 Installation Manual Revision 7.0 05102020... -
Page 11: Connection To Dc Power Source (Rack Mount)
Green Lead to (GND) Ground • Plug locking cables into the chassis inputs. NOTE: Do NOT disconnect locking plugs until source power has been powered off and discharged. PAGE 8 Edge Power Solutions EPS-32-V1 / EPS-32-V2 / EPS-16 Installation Manual Revision 7.0 05102020... -
Page 12: Connection To Dc Power Source (Wall Mount)
Wall Mount: EPS wall mount systems may utilize locking plug system for external power connections or internal direct power supply connections from an RMS equivalent DC power source or properly configured Digital Electricity™ receiver. Direct Power Supply Connection: Connection Point #1 in illustration below... -
Page 13: Section 3: Optional Integrated Fiber Optic Splitter
• 3.1.2 Output Connection: • Connect output from positions 1-32 on EPS-RM-1x32-100W-(s) or positions 1-16 on EPS-RM-1x16-100W-(S) • Patch other end to servicing device or device servicing fiber patch panel position. On 16 Port Unit, Utilize included 1x2 splitter for 2x16 connection.
Need help?
Do you have a question about the EPS-16 and is the answer not in the manual?
Questions and answers