Download Print this page

Climax Technology TSO-9-EL-ZBS Manual

Temperature sensor

Advertisement

Quick Links

Temperature Sensor (TSO-9-EL-ZBS)
Introduction
T
T
S
S
O -9-EL-ZBS is wireless temperature sensor with attached temperature probe. It can automatically or
O
manually transmits temperature condition to the coordinator in the ZigBee Network.
The Temperature Sensor utilizes ZigBee technology for wireless signal transmission. ZigBee is a wireless
communication protocol that is reliable and has low power consumption and high transmission efficiency.
Based on the IEEE802.15.4 standard, ZigBee allows a large amount of devices to be included in a network
and coordinated for data exchange and signal transmission.
The Temperature Sensor serves as an end device in the ZigBee network. It can be included in the ZigBee
network to transmit signal upon activation, but cannot permit any other ZigBee device to join the network
through the Temperature Sensor.
Parts Identification
Remove the cover by loosening the bottom fixing screw, the inside of the Temperature Sensor will be
revealed as shown.
1. External Temperature Probe Terminal
Connect the External Temperature Probe to this Terminal
2. Tamper Switch
The Tamper switch will be activated when the Temperature
Sensor is removed from mounted surface.
3. Internal LED
Flashes – when the Learn Button is pressed.
Flashes twice – when successfully joined a ZigBee network.
Flashes once every 20 minutes – lost connection to its current
ZigBee network.
4. Learn Button
Press the button once to transmit a test / temperature signal to
the ZigBee coordinator.
Press and hold the button for 10 seconds then release to reset the Temperature Sensor.
5. Battery Compartment
6. External Temperature Probe
Connect the Probe to External Temperature Probe Terminal
Features
T
T
e
e
m
m
p
p
e
e
r
r
a
a
t
t
u
u
r
r
e
e
The Temperature Sensor will transmit temperature signals to the ZigBee coordinator in every 10
minutes regularly.
If Temperature Sensor fails to receive acknowledgment from the Control Panel, it means that
Temperature Sensor has lost connection to the ZigBee coordinator, please check you ZigBee
coordinator condition.
When the temperature changes by +/- 2˚C, the Temperature Sensor will also transmit a signal.
You can also press the Function Button once to transmit a temperature signal manually.
The temperature detection range is about -30°C ~ 100°C ( -22°F ~ 212°F).
B
a
t
t
e
r
y
a
n
d
L
B
a
t
t
e
r
y
a
n
d
L
The Temperature Sensor uses one CR123 - 3V Lithium battery. Please always replace battery with
the correct size and voltage. When the Temperature Sensor is in low battery status, a low battery
signal will be sent to notify the user.
D
D
e
e
t
t
e
e
c
c
t
t
i
i
o
o
n
n
o
w
B
a
t
t
e
r
y
D
e
t
e
c
o
w
B
a
t
t
e
r
y
D
e
t
e
c
t
i
o
n
t
i
o
n
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the TSO-9-EL-ZBS and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Climax Technology TSO-9-EL-ZBS

  • Page 1 Temperature Sensor (TSO-9-EL-ZBS) Introduction O -9-EL-ZBS is wireless temperature sensor with attached temperature probe. It can automatically or manually transmits temperature condition to the coordinator in the ZigBee Network. The Temperature Sensor utilizes ZigBee technology for wireless signal transmission. ZigBee is a wireless communication protocol that is reliable and has low power consumption and high transmission efficiency.
  • Page 2 Battery Change  Remove the Cover by loosening the bottom fixing screw. Remove the Old Battery. Press the Tamper Switch or the Learn Button a few times. Fit a new battery into the battery compartment. Please orient the battery according to the correct polarity.
  • Page 3: Important Note

      There are two ways to mount the Temperature Sensor, by either Self-adhesive installation or Screw mounting. Self adhesive mounting  Clean the surface with a suitable degreaser. Remove the protective covering from one side of the double-sided adhesive pad and firmly apply to the back of the device.
  • Page 4: Fcc Radiation Exposure Statement

    FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
  • Page 5 Write Read / 0x0012 Boolean 0x00 –0x01 0x01 DeviceEnabled Write   Mandatory Identifier Name Type Range Access Default / Optional Unsigned Read / 0x0000 0x00 –0xffff 0x0000 IdentifyTime 16-bit integer Write   Mandatory Identifier Name Type Range Access Default / Optional MinMeasuredValue...