Krups EA870810 Intuition Manual page 26

Starting a drink:
– Check that the coffee bean container is full. If there is no coffee, the machine will
notify you via a warning light (V). Then press START/STOP to confirm the coffee refill.
Refer to section 8 - REFILLING THE COFFEE BEAN CONTAINER, fig 1 to 7.
Caution: Ensure that no water is poured into the grinder, so as not to damage
your machine.
– Check that the water tank is filled. If there is not enough water in the water tank,
the machine will flash up an alert (U) and ask you to fill the tank. Refer to section 7 -
REFILLING THE WATER TANK - fig 1 to 7.
– Place the cup or cups under the coffee nozzles.
– Press the button for the chosen drink.
Possible settings
For more information, refer to section 2 – BEVERAGE SETTINGS, fig 1 to 9.
FAVOURITES FUNCTION
The Favourites section, accessible by pressing
drink with a single press. Refer to section 2 – BEVERAGE SETTINGS, fig 1 to 9.
You can saved a Favourite A and a Favourite B. Refer to section 3 – SAVE YOUR FAVOURITE
SETTINGS / REPROGRAM A FAVOURITE, Fig 1 to 6.
– A favourite can only be saved after a drink has been made. You then have 10 seconds
to press the Favourites button to save your preferred drink in A or B.
– You can customise your volume by stopping the drink while it is running. Press
when it is running. The volume of your drink will then be saved in favourites.
Important:
When the flow stops, the machine returns automatically to its default drink. It is no
longer possible to save it as a favourite.
If you save a favourite when a drink has already been saved, that drink will be
deleted.
– Once a favourite has been saved, you can make your preferred drink by pressing a
single button . Then, follow the instructions in section 4 – START A FAVOURITE
BEVERAGE, Fig 1 to 6.
42
, allows you to access your preferred
DRINKS MADE USING STEAM
The steam nozzle (G) foams the milk to made a Cappuccino or Café Latte. As the steam
production requires a higher temperature than for making an espresso, the appliance
provides an additional preheating phase for the steam.
For manual milk foaming, use pasteurised or UHT milk from the refrigerator (3 - 5°C). The
use of special milks (micro filtered, raw, fermented, enriched) or plant milks (rice, oat or
almond milk) can give results that are less satisfactory in terms of quality and quantity of
froth.
It is not possible to make 2 cups at the same time: the "x2" function is not available.
The steps for making this drink with steam can be found in section 5 – MAKE A MILK
RECIPE, fig 1 to 11.
Please note:
There are 2 preheating times: one for the machine and one for the steam. The
LED flashes to indicate that the machine has finished preheating. Press "START/
STOP" again to start steam production. See section 5 - MAKE A MILK RECIPE,
fig 8.
Caution: risk of burns.
Important:
Steam production stops automatically depending on the steam time selected
previously. You can press "START/STOP" before the end of the cycle if the
amount of milk froth is sufficient.
THE CYCLE DOES NOT STOP IMMEDIATELY.
If you do not press the "START/STOP" button, the machine returns to its initial
position after 2 minutes.
– The Favourites program is available for the steam function.
Advice and Tips:
To make the milk froth, fill 1/3 of the cup with milk. Immerse the steam nozzle in the milk
and hold it against the edge of the cup. Tilt the cup 45°. This technique creates a milk
whirlpool, which makes the optimal amount of foam. By following these tips, you will
create a barista-quality milk froth ready to be used to make a milky drink.
CLEANING THE STEAM NOZZLE
Important:
In order to obtain identical froth each time, we recommend that you carefully
clean the tube and its connector AFTER EACH USE. Do not wash the steam
nozzle in the dishwasher.
Danger:
After using the steam function, the nozzle may be hot, we advise you to wait a
few moments before handling it.
43