Dexter Laundry DC50X2 Manual
  1. Manuals
  2. Brands
  3. Dexter Laundry Manuals
  4. Dryer
  5. DC50X2
  6. Manual

Dexter Laundry DC50X2 Manual

50 pound stacked commercial dryer
Hide thumbs Also See for DC50X2:
Table of Contents

Advertisement

Quick Links

Download this manual
DC50X2 Reversing Vended Models /
24VAC Control
50 Pound Stacked Commercial Dryer
Starting Serial # D1.15311.025
8533-098-001 7/21

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DC50X2 and is the answer not in the manual?

Questions and answers

Related Manuals for Dexter Laundry DC50X2

Summary of Contents for Dexter Laundry DC50X2

  • Page 1 DC50X2 Reversing Vended Models / 24VAC Control 50 Pound Stacked Commercial Dryer Starting Serial # D1.15311.025 8533-098-001 7/21...
  • Page 2 Equipment Safety Warnings Symbols and Terminology Used in this Equipment Indicates an imminently hazardous situation, which if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation, which if not avoided could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
  • Page 3 Equipment Safety Warnings Symbols and Terminology Used in this Equipment Warning! Do not operate equipment if door glass is damaged in any way. Warning! Keep clear of rotating parts. Prohibited! Do not enter this equipment or space. Prohibited! Do not step or stand on this equipment. Prohibited! Do not operate without all guards and covers in place.
  • Page 4 Indicates an imminently hazardous situation, which if not avoided, will result in death or seri- ous injury. Indicates a potentially hazardous situation, which if not avoided could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
  • Page 5 WARNING • All Dryers must be installed in accordance to all applicable electrical, plumbing and all other local codes. • These installation and operation instructions are for use by qualified personnel only. To avoid injury and electrical shock, do not perform any servicing other than that contained in the installation and op- eration instructions, unless qualified.
  • Page 6 WARNING Children should be supervised to ensure they do not operate or play in or around equipment. Keep all panels in place to protect against electrical shock and injury and add rigidity to washer. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a...
  • Page 7 Warning! Do not operate equipment if door glass is damaged in any way. Warning! Keep clear of rotating parts. Prohibited! Do not enter this equipment or space. Prohibited! Do not step or stand on this equip- ment. Prohibited! Do not operate without all guards and covers in place.
  • Page 8 Prohibited! Do not attempt to open, touch, or pro- ceed before referring to the manual or unless quali- fied. Mandatory! Read all supporting documentation be- fore operating or maintaining equipment. Mandatory! Disconnect power before servicing equipment. Mandatory! Lock out and tag out before servicing this equipment.
  • Page 9 Notes Part # 8533-098-001 7/21...

  • Page 10: Table Of Contents

    Dexter Safety Guidelines Table of Contents Section 1: WARNING Specifications ........14 & 15 Section 2: For your safety, the information in this manual Installation and Operation must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or loss of life.
  • Page 11 Section 6: End of Cycle ..........53 Wiring Diagram for DDAD Dryer ....54 Troubleshooting Wiring Schematic for DDAD Dryer ....55 Section 5: Quick Guide Troubleshooting ....... 66 Service Procedures Electronic Control Diagnostic Lights ....67 Trouble Shooting Fault Codes ....... 68 Clothes Door Removal .........
  • Page 12 Notes Part # 8533-098-001 7/21...

  • Page 13: Specifications

    Section 1: Specifications Part # 8533-098-001 7/21...

  • Page 14: Make Up Air

    SPECIFICATIONS 50 lb. Commercial Stack Dryer: T-50x2 Reversing Tumbler DC50X2NC-11EC2R (60 Hz), DC50X2NC-49AC2R (50 Hz) Cabinet Height 79 1/4” 2012 mm. (Assumes minimum leveling leg adjustment) Cabinet Width 34 1/2” 876 mm. Overall Depth 56 3/4” 1441 mm. Floor to Bottom of Door- Bottom Dryer 7”...
  • Page 15 Dexter Commercial 50 Pound Stacked Dryer Mounting Dimensions Part # 8533-098-001 7/21...
  • Page 16 Notes Part # 8533-098-001 7/21...
  • Page 17 Section 2: Installation & Operation Part # 8533-098-001 7/21...
  • Page 18 DRYER INSTALLATION 1. CODE CONFORMITY: All commercial dryer installations must conform with local codes, or in the absence of local codes, with the latest edition of the National Fuel Gas Code ANSI Z223.1. Canadian installations must comply with the current Standard CAN/CGA-B149 (.1 or .2) Installation Code for Gas Burning Appliances or Equipment, and local codes if applicable.

  • Page 19: Electrical Requirements

    3. MAKE-UP AIR: Adequate make-up air must be supplied to replace air exhausted by dryers on all types of installations. Refer to specifications for the minimum amount of make-up air opening to outside for each dryer. This is a net requirement of effective area. Screens, grills or lou vers, which will restrict the flow of air, must be considered.

  • Page 20: Exhaust Installation

    6. EXHAUST INSTALLATION. (Refer to Figure 3) Exhausting of the dryer(s) should be planned and constructed so that no air restrictions occur. Any restriction due to pipe size or type of installation can cause slow drying time, excessive heat, and lint in the room. From an operational standpoint, incorrect or inadequate exhausting can cause a cycling of the high limit thermostat, which shuts off the main burners and results in inefficient drying.
  • Page 21 NOTE: A small diameter duct will restrict airflow; a large diameter duct will reduce air 7. DRYER IGNITION (SOLID STATE IGNITION): The solid-state ignition system lights the main burner gas by spark. velocity - both contributing to lint build up. An inspection door should be provided for The gas is ignited and burns only when the gas-relay (in the electronic controller) calls for heat.

  • Page 22: Description Of Control

    DESCRIPTION OF DRYER CONTROL Both dryers are operated by the controller at the left midpoint of the dryer. The controller is two- in-one with the upper display and lights dedicated to the upper dryer and lower display and lights dedicated to the lower dryer. When money has been deposited, the control will prompt the user to choose a drying temperature and press the “start”...
  • Page 23 TRANSIENT VOLTAGE SURGE SUPPRESSORS Like most electrical equipment your new machine can be damaged or have its life shortened by voltage surges due to lightning strikes which are not covered by factory warranty. Local power distribution problems also can be detrimental to the life of electrical components. We recommend the installation of transient voltage surge suppressors for your new equipment.
  • Page 24 Notes Part # 8533-098-001 7/21...

  • Page 25: Programing

    Section 3: Programing C-Series Stack Dryer Part # 8533-098-001 7/21...

  • Page 26: Dexterlive

    DexterLive The new DexterLive controls were created for you to be able to interface easier with your equipment and create variable pricing cycles to increase your profitibility in the same floor 'H[WHU /LYH 3DJH  RI  space. First, log into DexterLive, create your location and equipment list and then create your cycle and pricing information by the particular type of washer and dryer at the location.
  • Page 27 First Time Creating an Account at Dexter Live Log into DexterLive At the bottom, select “Create your DexterLive account.” DexterLive gives an owner the ability to manage multiple locations. At the “Create a DexterLive Account” screen. First time users must create an account. An account must be created to use...
  • Page 28 Fill in the required fields and click on “Create My Account”. When creating a new user account make sure to fill in all fields marked with asterisks and check the “Terms of Service” box. After selecting to “Create My Account”, you will see the log in screen advising you to go to your e-mail and activate your account.
  • Page 29 Open the e-mail sent from Dexterlive and select “CONFIRM MY ACCOUNT” Selecting the “Confirm My Account” hyperlink will take you back to the DexterLive log in page. At the “Log into DexterLive” screen, enter your e-mail/user name and password to access DexterLive.
  • Page 30 Programming To configure your settings with DexterLive.com: Add or select a location to program. DexterLive gives an owner the ability to manage multiple locations and machines. On the left side of the screen, select the “Programming” tab. Follow instructions in programming tab.
  • Page 31 Edit the “General Settings” (Equipment Tab) Adjust setting and offset time to match your location. (Time is set for Central Standard Time) Next select the “+Add Equipment” (Equipment Tab), located in the upper right hand corner. Name of the machine. (Example: Dryer 1) Enter serial...
  • Page 32 When all of the equipment has been added, select “Edit” on the machine type you wish to modify, and then select “Pricing”. (Equipment Tab and Machine Settings Tab) Program the price of the machine and the extra pricing adders. Cycle changes can be made by selecting the “Cycles” tab. Adjust cycle programming set the length...
  • Page 33 If desired, you may create and edit optional store promotions from the “Promotions “Tab. Select “Save Promotion” once your changes have been made. Create and download the Programming File. Once all preferred prices, cycles and promotions have been modified and saved, select “DOWNLOAD PROGRAMMING FILE”.
  • Page 34     Based on your internet browser the file needs to be saved as “AllUser.xml”. Depending   on your Internet browser you may need to retrieve the file from   your “Downloads” folder, which is located under “Computer”. ...
  • Page 35 The machine will scroll “TO INSTALL – PRESS START”. At this prompt, press the green “Start” again. Once the program is uploaded successfully the control will scroll “DONE REMOVE USB”. The USB drive can be safely removed at this point. Note: All Dexter equipment (washers and dryers) featuring DexterLive controls can be programmed using this file once the equipment has been configured.

  • Page 36: Manual Program Mode

     PROGRAMMING THE DRYER CONTROL   The dryer control can be programmed to prompt the user for alternate vend prices, change dryer cycle  times, temperatures and many other options. This can be accomplished in two ways:  1. Manual programming utilizing the “Start”, “High”, “Medium” and “Low” buttons for the bottom dryer.
  • Page 37 When manual programming mode is entered, the “Start”, “High”, “Medium” and “Low” buttons for the lower dryer perform alternate functions. Please note that the changes made using the lower dryer buttons affect both upper and lower dryers. Button Name Alternate Function in Programming Mode Start Becomes the action to accept the displayed option or the “Enter”...
  • Page 38 These alternate functions allow the user to move through a menu of options to choose various program- mable settings. The figure below shows the top level menu. Choosing an option from the top level menu will then display the next level of options (the sub menu). Quick Test Option: When the Quick Test Option is chosen, the dryer will begin a shortened dry cycle without the displayed vend price being met.
  • Page 39 Continuous Test Option: Similar to the Quick Test, when the Continuous Test Option is chosen, the dryer will begin a dry cycle with- out the displayed vend price being met. However, in this case, it will be a continuously-running cycle. It will not time out after any designated amount of time.
  • Page 40 Prices Option: This option allows the user to set values for coin acceptor inputs, vend price & time and extend dry price & time. It also allows the user to return the values to factory defaults. After changing prices using the “Up” or “Down”...
  • Page 41 The figure below shows the sub menu options for Prices: Part # 8533-098-001 7/21...
  • Page 42 Cycles Option: This option allows the user to set temperature and cooldown information for the drying cycle. It also al- lows the user to return the values to factory defaults. 1. “TEMP SETTINGS” allows the user to make adjustments, within a designated range, to the cycling temperature for each of the “Low”, “Medium”...
  • Page 43 Part # 8533-098-001 7/21...
  • Page 44 Temperature Pricing Option: This option allows the user to require additional vend amounts be added based on the drying temperature chosen by the customer. This pricing adder is effective only for the Base Vend Price (it does not affect the Extend Dry Price).
  • Page 45 Settings Options: The Settings options allow for the user to make various programming changes to change how the control operation affects the customer. See below for detailed information on each next level option. 1. “Decimal Point”: If the user programs the Decimal Point to “OFF”, control display will not show a decimal point on any vend price values.
  • Page 46 8. “Shift Hours”: This feature allows the user to shift the time used by the control from the time kept internally by the control. The control uses a Real Time Clock (RTC) to internally track the time and date. The RTC continues operation even if the control loses external power. The RTC is set for Central Standard Time and no daylight savings.
  • Page 47 The figure below shows the sub menu options for Settings: Part # 8533-098-001 7/21...
  • Page 48 Usage Menu: The Usage menu allows for the user to track data about machine usage. See below for detailed information on each sub menu option. 1. “Coin Audit”: The coin audit field shows the accumulation of coin pulses that were sent to the control over each of the left and right coin inputs.
  • Page 49 Control Menu: The Control menu allows for the user to observe important technical information for the control. No chang- es can be made at this menu. See below for detailed information on each sub menu. 1. “Serial Number”: This is the control serial number. 2.
  • Page 50 REVERSING OPTIONS The dryer can be set to reverse at different intervals dependent on owner’s preference.  The style of operation is determined by the location of the BROWN jumper wire located  in the rear control box, on the frequency drive. (see image for jumper location) ...
  • Page 51 Notes Part # 8533-098-001 7/21...
  • Page 52 Notes Part # 8533-098-001 7/21...
  • Page 53 Section: 4 Schematic C-Series Stack Dryer Part # 8533-098-001 7/21...

  • Page 54: Dryer Idle- No Coins Added

    DC50X2 Reversing 60Hz. Wiring Schematic Dryer Idle - No Coins Added: Top Dryer Used For This Example 208/240 VAC 60 Hz. power is supplied to the main power trminal block and comes out on BLK/RED and BLK/BLU wire. 208/240 VAC now passes to the motor control relay (R1&R2) and also passes to the multi- tap control step-down transformer.

  • Page 55: Heat Circuit

    Heat Circuit Top Dryer Used For This Example With the blower motor running, 24 VAC provided through the centrifugal switch on the red wire and con- necting to the violet wire to the computer board gas relay. The temperature sensing probe is found under each tumbler in the lint tray area and sends resistance values back to the computer board for temperature sensing.

  • Page 56: End Of Cycle

    End of Cycle Top Dryer Used For This Example At the end of the cool down, the computer board opens the upper run relay, which removes power from the blower motor control relay (R1) and also removes power to the (R3) tumble relay which deactivates the variable frequency drive and motor.
  • Page 57 Notes Part # 8533-098-001 7/21...
  • Page 58 Wiring Diagram for DC50X2 Dryer   Part # 8533-098-001 7/21...
  • Page 59 Wiring Schematic for DC50X2 Dryer Part # 8533-098-001 7/21...
  • Page 60 Notes Part # 8533-098-001 7/21...

  • Page 61: Service Procedures

    Section 5: Service Procedures Part # 8533-098-001 7/21...

  • Page 62: Clothes Door Removal

    Service Procedures Clothes Door Removal 1. The clothes door may be removed from the hinge bracket by unscrewing and removing the allen- head pivot screw located at the door upper hinge point. 2. Next lean the door out of the top of the hinge bracket and lift the door from the bottom hinge pin.

  • Page 63: Pressure Regulator Adjustment

    B. Manual Reset Over Temperature Safety Thermostats- The second hi-limit thermostat is located on the right side of each burner housing as you view from the back of the machine. It is just above the gas valve and covered by a guard with a small access hole. 1.

  • Page 64: Electronic Control Diagnostic Lights

    Electronic Control Diagnostic Lights The electronic control has 6 diagnostic lights to aid in service of the dryer. Each pocket has indicator lights for the motor circuit, door switch circuit, and the heat circuit. When the electronic control is carefully unlocked and moved forward these lights are visible on the circuit board.

  • Page 65: Upper Front Panel Removal

    Upper Front Panel Removal The loading door does not have to be removed to remove the front panels on this model. 1. Remove the left two screws with finish washers. 2. Remove the right two screws with finish washers, at this time the front panel is loose but connected by the harness to the door switch.

  • Page 66: Air Flow Switch Operation And Adjustment

    4. Lift idler pulley straight up and block up or tie up in the extended position. 5. Remove the seven 7/16 nuts holding the blower motor assembly. Rocking the assembly to the left should allow you to remove the assembly. 6.

  • Page 67: Ignition System Function And Sequence

    Ignition System-Function & Sequence During normal dryer operation, the following occurs: 1. The dryer electronic control calls for heat. 2. If the drive motor is running, the motor safety circuit provides power to the electronic control. If the control senses that the heat should be on, a circuit is closed allowing power through the high limit thermostat and air flow switch to the ignition transformer.

  • Page 68: Main Burner Orifice Removal

    Main Burner Orifice Removal 1. Remove manifold and gas valve assembly as above. 2. Using an open end wrench, remove orifices from manifold. Main Burner Removal 1. Remove the 4 screws securing the cover for the burner housing and the one screw mounting the high limit cover.

  • Page 69: Troubleshooting

    Section 6: Troubleshooting C-Series Stack Dryer Part # 8533-098-001 7/21...

  • Page 70: Electronic Control Diagnostic Lights

    Trouble Shooting Electronic Control Diagnostic Lights The electronic control has 6 diagnostic lights to aid in service of the dryer. Each pocket has indicator lights for the motor circuit, door switch circuit, and the heat circuit. When the electronic control is carefully unlocked and moved forward these lights are visible on the circuit board.
  • Page 71 Upper Gas Light Upper Gas Light Upper Motor Light Model Selection Jumper Upper Motor Light Program Switch Upper Door Light Lower Door Light Figure: 1 Part # 8533-098-001 7/21...
  • Page 72 To enter a test Cycle Mode you will have to enter the programing mode: MANUAL PROGRAMMING: The dryer must be in idle mode for the manual programming menus to be accessed. Idle mode is when the dryer is not actively running a drying cycle and the vend price is displayed on the screen (for both upper and lower dryers).
  • Page 73 Error Codes Symptom Probable Cause Suggested Remedy TEMP SENSOR Shorted Temperature Sensor The dryer control shall not start until the SHORT or wire. detected short circuit is removed. Regardless of condition of short circuit, Error Code will be displayed until programming button is pressed to return machine to idle mode.
  • Page 74 TROUBLESHOOTING Suggested Symptom Probable Cause Remedy Tumbler does not turn Drive belts Check both drive belts. Replace if failed. Drive motor Check capacitor and motor. Replace if failed Door switch Check for door closed L.E.D on control board. Check door switch contacts and adjustment.
  • Page 75 Probable Symptom Suggested Remedy Cause Tumbler turns Glass fuse Check small glass control fuse in back of dryer. Replace but no spark at if failed. burner Temperature sensor The temperature sensor should have between 30,000 ohms and 60,000 ohms resistance at room temperature if okay.
  • Page 76 Symptom Probable Cause Suggested Remedy Tumbler turns, Gas supply Make sure gas supply is working. ignition sparks, no flame Gas pressure Make manometer check of gas pressure. Adjust if necessary. Spark electrode sensor Check for damage to electrode or mounting. Replace if necessary.
  • Page 77 Probable Symptom Suggested Remedy Cause Erratic display Initial start-up If erratic on initial start-up, leave power on for approximately one hour and check machine operation again. Grounding Machine must be grounded by separate conductor back to neutral bar in breaker box. Program Check program and make corrections if necessary.
  • Page 78 Notes Part # 8533-098-001 7/21...

  • Page 79: Parts Data

    Section 6: Parts Data DC50X2 -11 Reversing Dryer Part # 8533-098-001 7/21...
  • Page 80 Part # 8533-098-001 7/21...

  • Page 81: Cabinet Group

    Cabinet Group Key Description T-50X2-11 Reversing Door Assy., Loading Complete-Wht 9960-285-008 Door Assy., Loading Complete-SS 9960-285-011 Door Assy., Loading Complete-Chrome/BLK/SS 9960-285-007 Door Assy., Loading-SS(ring only) 9960-284-002 Door Assy., Loading-Chrome(ring only) 9960-284-004 Plate Assy., Hinge (Wht) 9982-353-002 Plate Assy., Hinge (SS) 9982-353-001 Screw, Hinge to Door 9545-012-015...
  • Page 82 Cabinet Group Continued Key Description T-50X2-11 Reversing Escutcheon, Upper 9994-032-001 Trim, Overlay-Upper Blue 9435-039-002 Trim, Overlay-Upper Black 9435-039-001 Escutcheon, Lower 9994-033-001 Trim, Overlay-Lower Blue 9435-023-001 Trim, Overlay-Lower Black 9435-031-001 Screw, #4-40 x 3/16 9545-020-009 Nameplate Stack Dryer Express Blue 9412-167-002 Nameplate Stack Dryer Express Black 9412-167-001 Lint Drawer Assembly Blue...
  • Page 83 20, 21 20, 21 Part # 8533-098-001 7/21...
  • Page 84 Part # 8533-098-001 7/21...
  • Page 85 Control Parts Group Key Description T-50X2-11 Reversing Controls Assy, Electronic Mounted With Membrane Switch, BLU 9857-198-002 Controls Assy, Electronic Mounted With Membrane Switch, BLK 9857-198-004 Trough Assembly 9826-008-001 Button-Push, Control, Black 9035-062-002 Button-Push, Control, Blue 9035-062-001 Spacer-Metal, 4mm 9538-166-011 Retainer-Push Button 9486-158-001 Nut-Hex, Elastic stop, #4-40 8640-424-002...

  • Page 86: Door Switch Group

    Door Switch Group Key Description T-50X2-11 Reversing Door Switches 9539-487-001 Hinge Plate Cover Key Description T-50X2-11 Reversing Cover-Hinge, Black 9074-340-002 Screw-TRHDCR, 10B x 3/8, Black 9545-008-010 Part # 8533-098-001 7/21...
  • Page 87 Rear Panel & Cover Group Key Description T-50 Rear Guard Side Panel 9208-090-001 Screws 10 AB x 3/8 9545-008-024 Label - Connection Electrical 8502-649-001 Rear Guard Back Panel 9208-089-001 Screws, Guard 9545-008-004 Label Warning & Notice 8502-600-001 Label - Instructions 8502-645-001 Transition Assembly Outlet 9109-113-001...

  • Page 88: Bearing Housing Group

    Bearing Housing Group Key Description T-50X2-11 Reversing Bearing Housing Complete Assy (Includes bearings 9803-201-001 & Spacer) Housing, Bearing 9241-189-002 Bearing, Ball, Front 9036-159-001 Spacer, Bearing 9538-183-001 Bearing, Ball, Rear 9036-159-003 Screw-Wizlock, 1/2-13x3/4 9545-017-017 Nut, 1/2-13 8640-417-002 Screw, 1/2-13x1 1/2 9545-017-018 Nut, 1/2-13 8640-417-002 Part # 8533-098-001 7/21...
  • Page 89 Tumbler Group Key Description T-50X2-11 Reversing Tumbler Assy Compleate W/Spider (GALV) 9848-154-001 Tumbler Assy (Galvinized) 9848-148-001 Tumbler Assy Compleate W/Spider (SS & Galv 9848-154-002 front) Tumbler Assy (Stainless Galvinized front) 9848-148-002 Rod, Tumbler 9497-226-002 Washer, Special 8641-590-002 Shim 9552-013-003 Spider Assy 9568-017-001 Nut, Wiz Lock 8640-417-005...

  • Page 90: Burner Housing Group

    Burner Housing Group Key Description T-50X2-11 Reversing Housing Assembly, Burner 9803-207-001 Service Burner Plate Front 9452-730-001 Service Plate baffle Recirculation Chamber Clean Out 9452-729-001 Screw, 10B x 3/8” 9545-008-006 Screw, 10B X 1/4” 9545-008-001 Angle, Burner Support 9003-220-001 Screw, 10B x 3/8” 9545-008-006 Burner, Main 9048-020-002...
  • Page 91 Burner Housing Group Photos Part # 8533-098-001 7/21...

  • Page 92: Rear View

    Rear View Photos Key Description T-50X2-11 Reversing Spacer, Tumbler pulley 9538-047-002 Pulley, Driven 9908-047-002 Tollerence Ring 9487-234-005 Washer-Flat, 1/2” 8641-581-026 Lock Washer, 1/2” 8641-582-016 Bolt, 1/2”-13 x 1” 1/4” 9545-017-009 Belt, Drive 9040-076-003 Air Flow Switch, Assembly 9801-098-001 Motor-Drive, 2Hp. 9376-319-001 Pulley-Motor, Drive 9453-169-012...
  • Page 93 Rear View Photos 2, 3, 4 Part # 8533-098-001 7/21...

  • Page 94: Control Assembly Group

    Control Assembly Group Key Description T-50X2-11 Reversing Control, Rear 9857-223-001 Bracket, Terminal Block Power 9029-202-001 Strip, Terminal Marker 9558-029-006 Terminal-Block, Power, 4 Pole 9897-035-001 Screw, 10AB x 3/8” 9545-008-024 Harness Assembly-Power Main Fork, Upper 9627-859-005 Harness Assembly-Power Main Fork, Lower 9627-859-006 Wire Assembly-Ground, GRN/YEL, 7”...
  • Page 95 Part # 8533-098-001 7/21...
  • Page 96 Coin Accecptor Key Description T-50X2-11 Reversing Coin Accecptor, Optical 9021-041-001 Sensor-Optical, Replacement 9801-099-001 Screw, Heighth Bar, 3mm 9454-039-002 Retainer, Coin Acceptor 9486-136-001 Screw, Torx T-10, 4BX5/8 ss 9545-053-002 Part # 8533-098-001 7/21...
  • Page 97 Air Flow Switch Assembly Key Description T-50X2-11 Reversing Air Flow switch Assy 9801-098-001 Bracket-Airflow switch 9029-200-001 Shield-Switch 9550-169-003 Switch-Micro 9539-461-009 Nut-Twin, 4-40 8640-401-001 Screw-.625, 4-40 9545-020-001 Actuator-Air Flow Switch 9008-007-001 Pin-Cotter, .09375x.75 9451-169-002 Screw, 10Bx1/4 9545-008-001 Harness Assembly, Overtemp/Airflow 9627-861-001 Part # 8533-098-001 7/21...
  • Page 98 Wiring Schematic for DC50x2   Part # 8533-098-001 7/21...
  • Page 99 Wiring Diagram for DC50x2 Part # 8533-098-001 7/21...
  • Page 100 Notes Part # 8533-098-001 7/21...
  • Page 101 Section 9: 50Hz. Part # 8533-098-001 7/21...

  • Page 102: Rear View

    Rear View Photos Key Description T-50X2-49 Reversing Spacer, Tumbler pulley 9538-047-002 Pulley, Driven 9908-047-002 Tollerence Ring 9487-234-005 Washer-Flat, 1/2” 8641-581-026 Lock Washer, 1/2” 8641-582-016 Bolt, 1/2”-13 x 1” 1/4” 9545-017-009 Belt, Drive 9040-076-003 Air Flow Switch, Assembly 9801-098-001 Motor-Drive, 2Hp. 9376-319-001 Pulley-Motor, Drive 9453-169-012...
  • Page 103 Rear View Photos 2, 3, 4 Part # 8533-098-001 7/21...

  • Page 104: Electrical

    Electrical Components Key Description T-50X2-49 Reversing Transformer, 200/230-24 VAC, 50/60HZ 8711-004-004 Strip-Marker, Terminal 9558-029-004 Key Description T-50X2-49 Reversing Control Assembly, Gas Valve 9857-132-004 Kit-Honeywell VR86, Valve Flange assy 9732-162-001 Orifice, Main Burner, #30 9425-069-002 Part # 8533-098-001 7/21...
  • Page 105 Air Flow Switch Assembly Key Description T-50X2-49 Reversing Air Flow switch Assy 9801-098-002 Bracket-Airflow switch 9029-200-002 Shield-Switch 9550-169-003 Switch-Micro 9539-461-009 Nut-Twin, 4-40 8640-401-001 Screw-.625, 4-40 9545-020-001 Actuator-Air Flow Switch 9008-007-001 Pin-Cotter, .09375x.75 9451-169-002 Screw, 10Bx1/4 9545-008-001 Harness Assembly, Overtemp/Airflow 9627-861-001 Part # 8533-098-001 7/21...
  • Page 106 Wiring Schematic for DC50x2 -49   Part # 8533-098-001 7/21...
  • Page 107 Wiring Diagram for DC50x2 -49 IMPORTANT: RETAIN THIS ELECTRICAL DIAGRAM FOR SERVICE. Part # 8533-098-001 7/21...
  • Page 108 Notes Part # 8533-098-001 7/21...

  • Page 109: Maintenance

    Section Maintenance Part # 8533-098-001 7/21...
  • Page 110 Step 3: Grease the bearings and the shaft of the intermediate pulley. Use an Alemite grease gun and Molykote BR2-S grease. (Where applicable) Dexter reserves the right to change part numbers and/or specifications Part # 8533-098-001 without notice. © 2010 Dexter Laundry, Inc. | 2211 W. Grimes Ave, Fairfield, IA 52556, U.S.A. | 1-800-524-2954 | www.dexter.com...

Table of Contents