Advertisement
Quick Links
How to Control PCS-418/426/436 with SDR-500series DVR
1. Connect the AC24V ,Video and RS-485 wire for PCS-418/426/436 as page 8
of PCS-400P Series Dome Installation & Set-up Guide.
Red wire: 24V AC Live, Blue wire: 24v ac Neutral,
Yellow wire: RS-485(A)+, Green wire:RS-485(B)-,
Coax: Video signal
2. Also connect above RS-485 wire and Video cable(BNC) to rear side of
SDR-500 Series as page 9 of User's Manual SDR-500 Series.
The Video out of SDR-500 series should be connect to the Video monitor,
3. After Power on PCS-400P series camera, SDR-500 series DVR and Monitor,
you can see the below screen. Should be used the USB mouse for controlling
and set-up (by connecting front side of SDR-500 Series).
Advertisement
Related Manuals for Ikegami PCS-418
Summary of Contents for Ikegami PCS-418
- Page 1 How to Control PCS-418/426/436 with SDR-500series DVR 1. Connect the AC24V ,Video and RS-485 wire for PCS-418/426/436 as page 8 of PCS-400P Series Dome Installation & Set-up Guide. Red wire: 24V AC Live, Blue wire: 24v ac Neutral, Yellow wire: RS-485(A)+, Green wire:RS-485(B)-, Coax: Video signal 2.
- Page 2 4. Click Icon which shown by red arrow, then following Login Screen displayed. Click Key board Icon which shown by red arrow. 5. Next Screen displayed as follows, please enter PASS WORD “ 1 1 1 1” The detail information for above Item 4.and Item5. are shown page 24 , 4.1 Login /Logout of User’s Manual SDR-500 Series.
- Page 3 6.The following screen is appeared, then click “Camera PTZ”. 7. Select the Protocol the red arrow showed point clicking.(Pelco-D example) In this case also the PCS-400P Series Protocol should be set up PELCO D with S3 switch page 11 of PCS-400P Series Dome Installation & Set-up Guide.
- Page 4 8.The next, click the following orange color point. Then below screen is displayed, red arrow shown point click and select the Baud Rate. “Pelco –D 2400” shall selected 2400bps in this case. Data bit ,Stop Bit, Parity, Menu, Tour, Pattern setting value is same as blow screen.
- Page 5 9.When you need to change the ID number for controlling PCS-400P series camera, click and set the red arrow shown point(+,- , ^ , also can be set) The camera side PCS-400P series ID set up proceeding is shown on page 11 to 13 of PCS-400P Series Dome Installation &...
- Page 6 11. Next screen appeared as below. Click “Exit “ 12.Next screen is shown the Blue Dome camera icon, this means CAM1 is set PTZ.(Icon on screen are shown on page52, 5.1 Viewing of User’s Manual SDR-500 Series.)
- Page 7 13.Control from SDR-500series. 13-1. Double click the camera picture (blue dome camera icon picture) on multi screen display, then full screen for PTZ camera is displayed. Pan Tilt Control shown on page53 and 54 , 5.15 Pan/Tilt Control of User’s Manual SDR-500 Series.
- Page 8 13-2. Right click on the screen then following SET UP MENU display on screen. Click the PTZ on SET UP MENU. Then blue dome camera icon picture is shown bottom of screen, as below shown picture, this means the PCS-400P series camera can be control from SDR-500series DVR.
- Page 9 13-3. Then cursor(Arrow for USB mouse) to the lower and near the center screen (and wait few second), the Key pad screen (camera control function is shown page 53 of User’s Manual. You can control manually PAN –TILT , ZOOM IN/OUT ,FOCUS ,(IRIS is auto iris only for PCS-400P series)as shown key pad by clicking.
- Page 10 13-5. Camera PCS-400P setup Key function. Fig-1 1. Number 10 -17 : Cursor shift 2. Number 7 : Close this Key pad screen 3. Number 3 :Select &Enter (PASS WORD: A A A A ) 4. Number 8 :Save preset 5.
- Page 11 And click the Number 3. Icon which are explained on 13-5. Fig-1 The following screen displayed Select the Tour numbers(should be already set-up by you),and click the Number 9. Icon which are explained on 13-5. Fig-1. Once again click the Number 9. Icon, then this Tour is stop and reset the Starting point.
Need help?
Do you have a question about the PCS-418 and is the answer not in the manual?
Questions and answers