Table of Contents
Advertisement
Available languages
Available languages
USER MANUAL
tubular motor Ø45 mm with electronic limit switch
Dear customer, thank you for purchasing a MASTER product.
This manual describe the operations for a correct installation of LINE. The tubular motors with electronic limit switch LINE series are suitable to command pergolas. The technical
characteristics are provided on the label stuck on motor. These devices have not been studied to a continuous working. Any other use is improper and forbidden and it could void
manufacturer's warranty. The manufacturer cannot be considered responsible for any damage due to improper, wrong or unreasonable use. The installation of the product must be
done by a qualified technician. At the end of the installation, all manuals must be given to the end user. Keep this manual for future reference!
Table of contents
01. Technical specifications
01. TECHNICAL SPECIFICATIONS
The technical characteristics of the motor are shown in the label applied to the motor tube. Before installing the motor, it is recommended to copy the technical data (including the full
name of the product) and store them in a safe place. These data may be useful in the event of subsequent maintenance or technical assistance. In addition to the technical data on the
motor tube (depending on the specific power of the motor), the common characteristics of the LINE motor family are:
Power supply
Stand-by consumption
Min roller diamete
02. WARNINGS
02.1 Warnings for safety
Incorrect installation can cause serious injuries
programming and maintenance operations must be carried out only by a qualified and skilled technician, who must comply with laws, provisions, local regulations and the instructions
●
given in this manual
The wiring must comply with current IEC standards. The final electrical system must be created only by the electrician
operation and can exclude the use of radio controls or require particular safety devices
shutter/awning regularly
02.2 Warnings for installation
Before installing the product, check the compatibility with the associated devices and accessories
knock and the use of unsuitable tools can cause the damage of the external or internal parts of the motor
parts without the manufacturer's permission
●
cable Any screws needed to complete the installation must not come into contact with the motor
●
shown on the motor)
Some stages of programming and/or normal operation make use of the mechanical stops of the roller shutter/awning. It is essential to choose a motor with the
most suitable torque for the application, considering the actual traction of the roller shutter/awning, and to avoid motors that are too powerful
●
1mm thick
Leave 1-2 mm of right/left play on the winding roller Check that the shape and size of the drive pulley and adapter crown correspond to the winding roller used. Adapters,
supports and sundry accessories related to the motor must be chosen exclusively from the MASTER catalogue
or from another support surface, the moving parts must be protected with a cover to prevent accidental access. In any case, ensure access for maintenance work
must be positioned in such a way that it does not come into contact with moving parts
●
the cable in a protective tube
If there are several radio appliances in the same system, they must not be less than 1,5m apart
Position the buttons within sight of the roller shutter/awning but a long way from its moving parts. Position the buttons more than 1.5 m from the floor
residential use; the maximum continuous operating time is 4 minutes
thermal cut-out, which stops the motor if it overheats. The motor returns to normal operation when its temperature drops below the safety limit (normally after 5 to 10 minutes)
motor must be installed so that it cannot come into contact with liquids and in any case in a position protected from atmospheric agents
cut the antenna cable as this would be dangerous. If the antenna cable is damaged, replace the product
powered
02.3 Warnings for use
The product is not intended to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they are
supervised or given instructions about the product way of use by a person responsible for their safety
●
distance, until the movement ends
being carried out (e.g. window cleaning, etc.). If the control device is automatic, disconnect the motor from the power line
R
: 230 Vac 50 Hz
IP insulation
: < 1W
Insulation class
: 50 x 1.5 mm
Continuous opeating time
Operating temperature
●
Keep these instructions for future maintenance work and disposal of the product
●
Do not carry the motor by the power cable. The product may not be used if the power cable is damaged. Do not try to replace the power
●
●
Do not allow children to play with the appliance or with the fixed control devices
LINE
Disposal
MASTER uses packaging recyclable materials. Dispose materials on the proper
containers, complying with the law in force in your locality.
This product may have substances that are polluting for the environment and
dangerous for the health.
At the end of the product life cycle, carefully comply with the waste disposal rules. It is
strictly forbidden to dispose the product on the domestic waste.
Notes on radio systems
It is advisable
to avoid using radio systems in areas with strong interference
police stations, airports, ports, hospital, etc). A technical inspection is in any case advisable before
installing any radio system in order to identify sources of interference.
Radio systems can be used where possible disturbances or malfunctioning of the transmitter or the
receiver do not cause a risk factor, or if the risk factor is cancelled by suitable safety systems.
The presence of radio device operating on the same transmission frequency (
with the radio receiver of the motor and so reduce the range of the system and limit the functionality of the
installation.
: I P44
: H
: 4 minutes
: -20 / +50°C
●
To prevent potentially dangerous situations, check the operating condition of the roller
●
Check that the package is intact and has not been damaged in transit
●
Do not pierce or tamper with the motor in any way. Do not modify or replace
●
The power of the motor must be sufficient for the applied load (check the rated data
●
The power cable of the product is suitable for indoor installation only. If installed outside, place
During operation, the motor body becomes very hot, so be careful
●
●
Check the automation during the movement and keep people at a safe
01
Operating frequency
Memorizable transmitters
Memorizable wind radio sensors
Memorizable sun radio sensors
●
All the product installation, connection,
●
Some applications require hold-to-run
●
Use winding rollers that are at least
●
If the product is installed at a height of less than 2.5 m from the floor
●
Do not install the product near metal surfaces
●
The motor contains a self-resetting
●
The antenna cable carries line voltage. Do not
For your safety, do not work near the winding roller while the motor is
●
Do not operate the blind when maintanance operations are
rev00.2 06.02.2020
(for example, near
433,42 MHz
) can interfere
:433.42 MHz
: 40
: 4
: 1
●
A heavy
●
The power cable
●
●
The motors are designed for
●
The
Advertisement
Chapters
Table of Contents
Need help?
Do you have a question about the LINE and is the answer not in the manual?
Questions and answers