ADTRAN T200 SHDSL Specifications

T200 SHDSL
LED INDICATORS
SINGLE PORT
PWR Off
Green
NTU
SHDSL Green
Yellow
SHDSL
NTU
Red
1225135L1
G.703 Off
Green
Off
PWR ALM
Yellow
SHDSL
Red
LBK Off
G.703
Green
ALM
Off
BERT
Green
LBK
Blinking Yellow
BERT
Red
LOOPBACK PUSHBUTTONS
LOC – Initiates a customer transparent loopback at the NTU
REM – Initiates a network transparent loopback at the LTU
LOC
BANTAM JACKS
L
B
K TX – G.703 signal received from the customer
REM
RX – G.703 signal transmitted to the customer
TX
G. POWERING
7
0
The LTU provides -113 VDC of span power over the SHDSL loop to the NTU, or the
3
NTU can be locally powered with a -48 VDC supply.
RX
V.
PROVISIONING
2
4
Used to access performance monitoring data, perform loopbacks and provision units
via VT100 emulation software such as Hyper Terminal – Private Edition and
ProComm Plus. When using a PC with terminal software, be sure to disable any
power saving programs. Provision terminal port as follows:
Data Rate – 1.2 to 19.2 kbps
Asynchronous Data Format – eight data bits, no parity (none), one stop bit
There are two types of terminal emulation modes, Manual and Real Time. Use
"CTRL-T" to toggle between the two modes.
Manual Emulation Mode
Press the space bar 3 times to manually update the screen. Print screen and log file
commands are available in this mode.
C A U T I O N !
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
T200 SHDSL SINGLE PORT NTU
No power
Adequate power
SHDSL Loop is trained
SHDSL Loop is trained with marginal signal quality (SNR
margin)
SHDSL Loop is not trained
G.703 port not configured, or in alarm condition
G.703 port configured and no alarms
No alarm condition detected
Remote alarm condition detected
Alarm condition detected locally
Module is not in loopback
Local loopback is active
Module is not in BERT
BERT running with no errors
Module is running a BERT with bit errors
BERT running with no pattern sync
For a complete Installation and Maintenance Practice: (877) 457-5007, faxback Document 768. Please have your fax number ready.
Real-Time Emulation Mode
The default mode. Print screen and log file commands are not available in this mode.
Cursor placement and screen highlighting are enabled.
Refer to the menu tree on the reverse side to navigate the SHDSL NTU menu options.
DEFAULT PROVISIONING OPTIONS
Provisioning Option Default Value
Unit Options
Local Management Enabled
SHDSL Options
Aggregate Rate N/A
SNR Margin Alarm Threshold (dB) Disabled
Loop Attenuation Alarm Threshold (dB) Disabled
Line Probing Disabled
G.703 Options
ISDN-PRA V3 Disabled
G.704 CRC-4 Multiframing Disabled
G.704 Idle Pattern FFh
Network Spare Bits Insertion Disabled
Network Spare Bits Pattern N/A
Customer Spare Bits Insertion Disabled
Customer Spare Bits Pattern N/A
Customer RAI Generation Disabled
Customer E-bit Generation N/A
Test Options
SHDSL Remote Loopback Disabled
SHDSL BERT Normal
G.703 Local Loopback Enabled
COMPLIANCE
This product is intended for installation in restricted access locations only and in
equipment with a type "B" or "E" enclosure.
Code Input Output
Power Code (PC) F C
Telecommunication Code (TC) – X
Installation Code (IC) A –
WARRANTY
Warranty for Carrier Networks products manufactured by ADTRAN and supplied under
Buyer's order for international use is five (5) years. For a complete copy of ADTRAN's
International Equipment Warranty, part number 60000003#I-3: (877) 457-5007,
faxback Document 583.
JOB
A
ID
61225135L1-22A
0206