Advertisement
DIMMABLE LIGHTS FUNCTION
INITIAL OPERATING CONDITION
The manufacturer supplies the radio control unit
THIS FUNCTION PROVIDES FOR LIGHTS DIM-
ready to be used with codes preset in the Factory
MABILITY, RANGING FROM 20% TO 100% , BY
CONTINUOUSLY PRESSING THE LIGHT KEY
ON THE REMOTE CONTROL.
FUNCTIONS ARE THE FOLLOWING:
of
L E A R N I N G T H E N E W T R A N S M I S S I O N C O D E :
- HOOD LIGHT OFF - SHORTLY PRESS THE
KEY - LIGHT ON AT 100%.
OPERATION MODE
Once the transmission code is changed in the radio control unit, the electronic central unit of the
Standard configuration:
cooker hood must be made to set the new code in the following way:
Standard configuration requires all "cooker hoods
- LIGHT ON AT 100% - SHORTLY PRESS THE
– radio control - system" to be provided with the
KEY - LIGHT OFF.
same transmission code. In the event two cooker
Press the main power-off button on the hood and then restore power to the electronic control
hoods – radio control system are installed in the
- LIGHT ON AT 100% - CONTINOUSLY PRESS
same room or nearby, each system may affect
unit. Within the next 15 seconds, press the light button
THE KEY - BRIGHTNESS REDUCTION.
the operation of the another. Therefore, the code
the code.
of one radio control system must be changed.
- RELEASING THE KEY DURING REDUCTION
co-
OR INCREASE - LIGHT KEEPS THE LUMINOUS
Generating a new transmission code:
INTENSITY REACHED.
The radio control system is provided with preset
R E S E T O F T H E FA C TO RY C O N F I G U R AT I O N :
codes. Should new codes be required, proceed
as follows: Press simultaneously buttons:
To restore the Factory configuration, follow the procedure described below: simultaneously press
- LIGHT ON - DIMMED - CONTINOUSLY
PRESS THE KEY - BRIGHTNESS IS INVERTED
buttons:
IF COMPARED TO THE PREVIOUS FUNCTION.
seconds). LEDs flashing 6 times indicate the procedure is completed.
for two seconds. When Leds light on, press but-
tons:
WA R N I N G :
This operation permanently deletes the preset codes.
(within 5 seconds). Leds flashing 3 times indicate
M-
the procedure is completed.
BY
KEY
E M E R G E N C Y B U T TO N :
WARNING! This operation deletes permanen-
tly the preset codes.
In the event that the radio control does not work, use the emergency button to switch the
Learning the new transmission code:
appliance off. After any necessary repairs have been performed, reset the emergency button.
Once the transmission code is changed in the ra-
THE
dio control unit, the electronic central unit of the
WA R N I N G :
cooker hood must be made to set the new code
in the fol- lowing way:
THE
The battery should be replaced every year to guarantee the optimal range of the transmitter.
Press the main power-off button of the hood and
then restore power to the electronic control unit.
Within the next 15 seconds, press the Liight But-
ESS
To replace the exhausted battery, take the plastic lid off, remove the battery and replace it with a
ton
to synchronise the central unit with the
code.
new one, observing the correct battery polarities.
ON
Reset of the Factory configuration:
OUS
Used batteries should be discarded in special collection bins.
To restore the Factory configuration, follow the
procedure described below: press simultaneou-
sly buttons:
SLY
WA R N I N G :
ED
N.
Any adjustments or modifications which have not been expressly approved by the holder of the
legal conformity certificate may invalidate the user's rights relating to the operation of the device.
19
The products are endowed with an electronic device which allows the automatic switching off
after 4 hours working from the last operation.
16
Instruction manual COR540SL
for 2 seconds. When Leds light on, press buttons:
Please keep this instruction manual for future reference
(within 5 seconds). Leds flashing 3 times indicate
the procedure is completed.
WARNING! This operation deletes permanen-
tly the preset codes.
Learning the new transmission code:
Once the transmission code is changed in the ra-
dio control unit, the electronic central unit of the
cooker hood must be made to set the new code
in the fol- lowing way:
Press the main power-off button of the hood and
then restore power to the electronic control unit.
Within the next 15 seconds, press the Liight But-
to synchronise the central unit with
ton
to synchronise the central unit with the
code.
Reset of the Factory configuration:
To restore the Factory configuration, follow the
procedure described below: press simultaneou-
for 2 seconds. When Leds light on, press buttons:
sly buttons:
(within 5 seconds). Leds flashing 6 times indicate
the procedure is completed.
19
WARNING! This operation deletes permanen-
tly the preset codes.
Emergency button:
In the event that the radio control does not work,
use the emergency button to switch the appliance
off. After any necessary repairs have been perfor-
med, reset the emergency button.
WARNING
The battery should be replaced every year to
guarantee the optimal range of the transmitter.
To replace the exhausted battery, take the pla-
stic lid off, remove the battery and replace it
with a new one, observing the correct battery
polarities.
Used batteries should be discarded in special
collection bins.
The below product:
RC001 Radiio Controll
complies with the specifications set out in the
R&TTE Directive 99/5/EC.
WARNING
Any adjustments or modifications which have
not been expressly approved by the holder of
the legal conformity certificate may invalidate
the user's rights relating to the operation of
the device.
The products are endowed with an electronic de-
vice which allows the automatic switching off after
4 hours working from the last operation.
TIMING
As a res
(within 5
EU66 " E
ropean C
from Jan
adapted
All of the
requirem
including
trol, whe
Internal m
city high
timer dev
tion spee
operation
External
motors th
de a time
speed w
Motors In
Remote
650m³/h
following
suction s
to 2nd sp
If the app
matically
operation
ged durin
The ene
stand – b
Rev. 0 26/08/14
Advertisement
