Advertisement
D I M M A B L E L I G H T S F U N C T I O N
This function provides for light dimmability, ranging from 20% to 100%, by continuously pressing
the light key on the remote control.
Functions are the following:
› Hood light off - shortly press the key - light at 100%
› Light on at 100% - shortly press the key - light off
› Light on at 100% - continuously press the key - brightness reduction
INITIAL OPERATING CONDITION
› Releasing the key during reduction or increase - light keeps the luminous intensity reached
The manufacturer supplies the radio control unit
ready to be used with codes preset in the Factory
› Light on - dimmed - continuously press the key - brightness is inverted if compared to the
WORKING
previous function
eration of
RC001
R
C
ADIO
I N I T I A L O P E R AT I N G C O N D I T I O N
ONTROL
OPERATION MODE
adio control used for the remote operation of
Standard configuration:
The manufacturer supplies the radio control unit ready to be used with codes preset in the Factory.
7A
ucted cooker hoods.
Standard configuration requires all "cooker hoods
– radio control - system" to be provided with the
ECHNICAL DATA
same transmission code. In the event two cooker
Alkaline battery powered: 12 V mod. 27A
S TA N DA R D C O N F I G U R AT I O N
hoods – radio control system are installed in the
Operating frequency: 433.92 Mhz
same room or nearby, each system may affect
Standard configuration requires all "cooker hoods – radio control - system" to be provided with
Combinations: 32.768
the operation of the another. Therefore, the code
Max. consumption: 25 mA
the same transmission code. In the event two cooker hoods – radio control system are installed in
of one radio control system must be changed.
Operating temperature: -20 ÷ + 55 °C
ns for co-
the same room or nearby, each system may affect the operation of the another. Therefore, the code
Dimensions: 130x45x15 mm.
Generating a new transmission code:
elow:
of one radio control system must be changed.
The radio control system is provided with preset
OPERATING DESCRIPTION
codes. Should new codes be required, proceed
he transmitter is equipped with 5 buttons for co-
as follows: Press simultaneously buttons:
ker hood management, as specified below:
mand.
G E N E R AT I N G A N E W T R A N S M I S S I O N C O D E :
: Light ON/OFF command.
The radio control system is provided with preset codes. Should new codes be required, proceed
for two seconds. When Leds light on, press but-
: Motor ON (speed level 1) / OFF command.
as follows: Press simultaneously buttons:
tons:
: Reduce speed.
press buttons:
: Increase speed.
is completed.
: 10-minute timer.
(within 5 seconds). Leds flashing 3 times indicate
HTS DIM-
the procedure is completed.
100% , BY
DIMMABLE LIGHTS FUNCTION
WA R N I N G :
GHT KEY
WARNING! This operation deletes permanen-
HIS FUNCTION PROVIDES FOR LIGHTS DIM-
This operation permanently deletes the preset codes.
tly the preset codes.
MABILITY, RANGING FROM 20% TO 100% , BY
ONTINUOUSLY PRESSING THE LIGHT KEY
Learning the new transmission code:
ON THE REMOTE CONTROL.
Once the transmission code is changed in the ra-
RESS THE
dio control unit, the electronic central unit of the
UNCTIONS ARE THE FOLLOWING:
cooker hood must be made to set the new code
in the fol- lowing way:
RESS THE
HOOD LIGHT OFF - SHORTLY PRESS THE
Press the main power-off button of the hood and
EY - LIGHT ON AT 100%.
then restore power to the electronic control unit.
Within the next 15 seconds, press the Liight But-
LY PRESS
LIGHT ON AT 100% - SHORTLY PRESS THE
ton
to synchronise the central unit with the
EY - LIGHT OFF.
code.
DUCTION
LIGHT ON AT 100% - CONTINOUSLY PRESS
Reset of the Factory configuration:
UMINOUS
HE KEY - BRIGHTNESS REDUCTION.
To restore the Factory configuration, follow the
procedure described below: press simultaneou-
RELEASING THE KEY DURING REDUCTION
sly buttons:
INOUSLY
OR INCREASE - LIGHT KEEPS THE LUMINOUS
NVERTED
NTENSITY REACHED.
NCTION.
INITIAL OPERATING CONDITION
The manufacturer supplies the radio control unit
ready to be used with codes preset in the Factory
OPERATION MODE
Standard configuration:
Standard configuration requires all "cooker hoods
– radio control - system" to be provided with the
same transmission code. In the event two cooker
hoods – radio control system are installed in the
same room or nearby, each system may affect
the operation of the another. Therefore, the code
of one radio control system must be changed.
Generating a new transmission code:
The radio control system is provided with preset
codes. Should new codes be required, proceed
as follows: Press simultaneously buttons:
(within 5 seconds). LEDs flashing 3 times indicate the procedure
for two seconds. When Leds light on, press but-
tons:
(within 5 seconds). Leds flashing 3 times indicate
the procedure is completed.
WARNING! This operation deletes permanen-
tly the preset codes.
Learning the new transmission code:
Once the transmission code is changed in the ra-
dio control unit, the electronic central unit of the
cooker hood must be made to set the new code
in the fol- lowing way:
Press the main power-off button of the hood and
then restore power to the electronic control unit.
Within the next 15 seconds, press the Liight But-
ton
to synchronise the central unit with the
code.
Reset of the Factory configuration:
To restore the Factory configuration, follow the
Please keep this instruction manual for future reference
procedure described below: press simultaneou-
for two seconds. When LEDs light on,
Instruction manual COR540SL
15
Advertisement
