Table of Contents
Advertisement
Quick Links
Installation and Operational Instructions for
®
ROBATIC
-clutch Type 500.1_ _ and Type 580.1_ _
Sizes 3 – 9
Please read the Operational Instructions carefully and follow them accordingly!
Ignoring these Instructions may lead to malfunctions or to clutch failure, resulting in damage to other parts.
Contents:
Page 1: - Contents
- Manufacturer's Declaration
- Safety and Guideline Signs
Page 2: - Safety Regulations
Page 3: - Safety Regulations
Page 4: - Clutch Illustrations
Page 5: - State of Delivery
Page 6: - Installation Examples
Page 7
- Installation
Page 8: - Maintenance and Inspection
Manufacturer's Declaration
This product is intended for installation in a machine or system, based on the machine directive 98/37/EC.
It is forbidden to start use of the product until the machine or system into which it should be built is operating in accordance with the EC
directives.
The product corresponds to the low voltage directive 73/23/EEC.
The customer is responsible for compliance with the EMC directive 89/336/EEC.
Safety and Guideline Signs
Danger!
Danger of injury to personnel and damage to machines.
Please Observe!
Guidelines on important points.
Please Observe:
According to German notation, decimal points in this document are represented with a comma (e.g. 0,5 instead of 0.5).
28/08/2007 TK/RB/RJ
Page 1 of 8
Chr. Mayr GmbH + Co. KG
Eichenstraße 1
87665 Mauerstetten
Germany
Tel.: 08341 / 804-241
Fax: 08341 / 804-422
http://www.mayr.de
eMail:
info@mayr.de
(B.5.0.GB)
Advertisement
Table of Contents
Related Manuals for Mayr ROBATIC 500.1 Series
Summary of Contents for Mayr ROBATIC 500.1 Series
- Page 1 Guidelines on important points. Please Observe: According to German notation, decimal points in this document are represented with a comma (e.g. 0,5 instead of 0.5). 28/08/2007 TK/RB/RJ Chr. Mayr GmbH + Co. KG Tel.: 08341 / 804-241 Eichenstraße 1 Fax: 08341 / 804-422 87665 Mauerstetten http://www.mayr.de...
- Page 2 Thermic Class F (+155 ° C) The magnetic coil and the casting compound are suitable for use up to a maximum operating temperature of +155 ° C. 28/08/2007 TK/RB/RJ Chr. Mayr GmbH + Co. KG Tel.: 08341 / 804-241 Eichenstraße 1 Fax: 08341 / 804-422 87665 Mauerstetten http://www.mayr.de...
- Page 3 GmbH + Co. KG Sales and Delivery Conditions. On contact with chemical materials, please check for compatibility. ® Mistakes or deficiencies are to be reported to mayr once! Install additional protective measures against corrosion if the brake is subject to extreme ambient conditions or is installed in open air conditions, unprotected from the weather.
- Page 4 Type 580.1_ _ [Nm] Please observe run-in specifications and minimum speed acc. Table 2 Not included in standard delivery 28/08/2007 TK/RB/RJ Chr. Mayr GmbH + Co. KG Tel.: 08341 / 804-241 Eichenstraße 1 Fax: 08341 / 804-422 87665 Mauerstetten http://www.mayr.de...
- Page 5 (% duty cycle). Table 2 Friction work Q Clutch speed n Size [rpm] 28/08/2007 TK/RB/RJ Chr. Mayr GmbH + Co. KG Tel.: 08341 / 804-241 Eichenstraße 1 Fax: 08341 / 804-422 87665 Mauerstetten http://www.mayr.de Page 5 of 8...
- Page 6 Exception for size 4: Here, the keyway is produced up to Ø 23 keyway acc. DIN 6885/1 and over Ø 23 keyway acc. DIN 6885/3. We recommend H7/k6 as a suitable hub-shaft tolerance. 28/08/2007 TK/RB/RJ Chr. Mayr GmbH + Co. KG Tel.: 08341 / 804-241 Eichenstraße 1 Fax: 08341 / 804-422 87665 Mauerstetten http://www.mayr.de...
- Page 7 Examples Figs. 3 and 4. Axial backlash can lead to the rotor (3) rubbing against the armature disk (4) or the coil carrier (1 / 2). 28/08/2007 TK/RB/RJ Chr. Mayr GmbH + Co. KG Tel.: 08341 / 804-241 Eichenstraße 1 Fax: 08341 / 804-422 87665 Mauerstetten http://www.mayr.de...
- Page 8 Interrupted coil Replace clutch Clutch does not couple Grease and / or oil on the friction surfaces De-grease friction surfaces 28/08/2007 TK/RB/RJ Chr. Mayr GmbH + Co. KG Tel.: 08341 / 804-241 Eichenstraße 1 Fax: 08341 / 804-422 87665 Mauerstetten http://www.mayr.de...
Need help?
Do you have a question about the ROBATIC 500.1 Series and is the answer not in the manual?
Questions and answers