RPS
50 Gear Driven Sprinkler Setting Instructions
®
NOTE: The RPS 50 is factory preset with a 40° arc setting, and includes a pre-installed #1.5 nozzle.
CHANGING A NOZZLE
1
REMOVING THE NOZZLE RETENTION SCREW
Use the Key (A) to remove the nozzle retention screw (B) by turning
counter-clockwise to remove or clockwise to re-install.
2
PULL UP THE RISER
Insert the Key (A) in the keyhole (C) on the top of the nozzle turret (D)
and turn the key 1/4 turn to insure that the key does not slip out of the
keyhole when you pull it up. Firmly pull up the entire spring-loaded riser
to access the nozzle socket (E). Hold the riser assembly with one hand.
3
REMOVING THE NOZZLE
STANDARD NOZZLE PERFORMANCE
With nozzle retention screw removed, the nozzle may be removed by
either turning on the water (wear safety glasses when using this method),
U.S.
or by pulling outward on nozzle wing (F) with a pair of needle-nose pliers.
Nozzle Pressure Radius
PSI
4
INSTALLING A NOZZLE
#3
30
Press the desired nozzle (G) into the nozzle socket (E). Make sure the
40
nozzle number is visible and the nozzle wing (F) are up. Then, re-install
50
the nozzle retention screw (B). NOTE: The nozzle retention screw is also
60
a break-up screw and used to adjust the distance of the spray.
#0.5
30
40
SETTING THE ARC ADJUSTMENT
50
60
NOTE: The RPS50 Gear Driven Sprinkler has
#0.75
a fixed right start and an adjustable left stop.
30
40
50
1
POSITIONING NOZZLE TURRET TO ITS "RIGHT START"
60
Place your finger on the top center of the nozzle turret (D). Rotate the
#1
30
turret counter-clockwise to the left stop to complete any interrupted
40
rotation cycle. Rotate the nozzle turret clockwise to the right start.
50
This is the fixed side of the arc. The nozzle turret must be held in this
60
position for arc adjustments. The right start does not change.
#2
30
2
40
ADJUSTING THE RIGHT (FIXED) SIDE OF ARC
50
If the right side of the arc is not properly aligned, sprinkler may
60
spray in areas not intended for watering such as driveways or
#4
30
adjacent properties. The right side arc can easily be realigned.
40
50
OPTION 1: REPOSITION CAN ON THE FITTING
60
Turn the housing can left or right to the desired position.
#6
30
This may require temporary removal of the soil around the
40
sprinkler to allow you to grip the sprinkler can.
ius
Flow
Pressure Radius
50
GPM
KPa
Bars
60
OPTION 2: REMOVE INTERNAL RISER ASSEMBLY AND REPOSITION
'
2.0
206
2.1
Unscrew the top counter-clockwise and remove the internal sprinkler
#8
40
'
2.4
275
2.8
assembly (J) from the can (K). Once removed with nozzle turret (D) at its
50
'
2.7
344
3.4
60
right start, reposition the riser assembly so that nozzle arrow points to
'
2.9
413
4.1
70
the desired start position. Replace the riser assembly back in the can and
'
0.5
206
2.1
screw on the top. At this point you have realigned the right arc stop, and
'
0.6
275
2.8
you can adjust the left arc to an appropriate setting.
'
0.7
344
3.4
'
0.8
413
4.1
'
0.7
206
2.1
(continued on reverse side)
'
0.8
275
2.8
'
0.9
344
3.4
'
1.0
413
4.1
Flow
Pressure Radius
Ft.
GPM
KPa
36'
2.0
206
2.1
38'
2.4
275
2.8
40'
2.7
344
3.4
40'
2.9
413
4.1
28'
0.5
206
2.1
29'
0.6
275
2.8
29'
0.7
344
3.4
30'
0.8
413
4.1
29'
0.7
206
2.1
30'
0.8
275
2.8
30'
0.9
344
3.4
31'
1.0
413
4.1
30'
0.9
206
2.1
31'
1.0
275
2.8
31'
1.2
344
3.4
32'
1.3
413
4.1
32'
1.2
206
2.1
33'
1.4
275
2.8
34'
1.6
344
3.4
34'
1.8
413
4.1
36'
2.6
206
2.1
40'
3.0
275
2.8
42'
3.4
344
3.4
42'
3.7
413
4.1
38'
4.2
206
2.1
METRIC
43'
4.9
275
2.8
Flow
46'
5.5
344
3.4
Meters
L/M
M
/H
3
47'
6.0
413
4.1
11.0
7.6
0.45
45'
6.0
275
2.8
11.6
9.1
0.55
48'
6.8
344
3.4
12.2
10.2
0.61
49'
7.6
413
4.1
12.2
11.0
0.66
482
4.8
51'
8.2
8.5
1.9
0.11
8.8
2.3
0.14
8.8
2.7
0.16
9.1
3.0
0.18
8.8
2.6
0.16
9.1
3.0
0.18
9.1
3.4
0.20
9.4
3.8
0.23
METRIC
Flow
Bars
Meters
L/M
11.0
7.6
11.6
9.1
12.2
10.2
12.2
11.0
8.5
1.9
8.8
2.3
8.8
2.7
9.1
3.0
8.8
2.6
9.1
3.0
9.1
3.4
9.4
3.8
9.1
3.4
9.4
3.8
9.4
4.5
9.8
4.9
9.8
4.5
10.1
5.3
STANDARD NOZZLE PERFORMANCE
10.4
6.1
10.4
6.8
Nozzle Pressure Radius
11.0
9.8
#3
12.2
11.4
12.8
12.9
LOW ANGLE NOZZLE PERFORMANCE
12.8
14.0
#0.5
11.6
15.9
U.S.
13.1
18.5
#0.75
Nozzle Pressure Radius
14.0
20.8
PSI
14.3
22.7
#1
#1
30
13.7
22.7
40
14.6
25.7
#2
50
14.9
28.8
60
15.5
31.0
#4
#3
30
40
50
#6
60
#4
30
#8
40
50
60
A
Key
Keyhole
LOW ANGLE NOZZLE PERFOR
B
Nozzle
Retention
Nozzle Pressure Radius
Screw
STANDARD NOZZLE PERFORMANCE
M
/H
3
E
Nozzle
U.S.
Nozzle Pressure Radius
Flow
Pressure Radius
Socket
PSI
Ft.
GPM
KPa
0.45
#1
#3
30
36'
2.0
206
40
38'
2.4
275
0.55
50
40'
2.7
344
60
40'
2.9
413
#0.5
30
28'
0.5
206
0.61
40
29'
0.6
275
50
29'
0.7
344
60
30'
0.8
413
0.66
#0.75
30
29'
0.7
206
40
30'
0.8
275
50
30'
0.9
344
60
31'
1.0
413
0.11
#3
#1
30
30'
0.9
206
40
31'
1.0
275
0.14
50
31'
1.2
344
60
32'
1.3
413
#2
30
32'
1.2
206
0.16
40
33'
1.4
275
50
34'
1.6
344
60
34'
1.8
413
0.18
#4
30
36'
2.6
206
40
40'
3.0
275
50
42'
3.4
344
0.16
#4
60
42'
3.7
413
#6
30
38'
4.2
206
40
43'
4.9
275
0.18
50
46'
5.5
344
60
47'
6.0
413
#8
40
45'
6.0
275
0.20
50
48'
6.8
344
60
49'
7.6
413
F
70
51'
8.2
482
0.23
Nozzle
0.20
#6
G
Nozzle
Wing
0.23
0.27
0.30
0.27
Data represents test results in zero wind for the R
0.32
Radius may be reduced with nozzle retention scre
0.36
0.41
U.S.
METRIC
Flow
Pressure Radius
STANDARD NOZZLE PERFORMANCE
0.59
PSI
Ft.
GPM
KPa
Bars
Meters
C
Key in
U.S.
30
36'
2.0
206
2.1
0.68
Nozzle Pressure Radius
Flow
Pressure Radius
40
38'
2.4
275
2.8
Keyhole
50
40'
2.7
344
3.4
0.77
PSI
Ft.
GPM
KPa
60
40'
2.9
413
4.1
#3
30
36'
2.0
206
0.84
30
28'
0.5
206
2.1
40
38'
2.4
275
40
29'
0.6
275
2.8
50
40'
2.7
344
50
29'
0.7
344
3.4
60
40'
2.9
413
0.91
60
30'
0.8
413
4.1
#0.5
30
28'
0.5
206
1.11
30
29'
40
0.7
29'
206
0.6
2.1
275
Flow
Pressure Radius
40
30'
50
0.8
29'
275
0.7
2.8
344
1.25
60
30'
0.8
413
50
30'
0.9
344
3.4
60
31'
1.0
413
4.1
Ft.
GPM
KPa
#0.75
30
29'
0.7
206
J
1.36
40
30'
0.8
275
30
30'
0.9
206
2.1
50
30'
0.9
344
40
31'
1.0
275
2.8
Internal
22'
60
1.2
31'
1.0
207
413
1.36
50
31'
1.2
344
3.4
60
#1
32'
30
1.3
30'
413
0.9
4.1
206
Sprinkler
24'
1.7
275
1.54
40
31'
1.0
275
30
32'
1.2
206
2.1
50
31'
1.2
Assembly
344
26'
1.8
344
40
33'
1.4
275
2.8
1.73
60
32'
1.3
413
50
34'
1.6
344
3.4
28'
2.0
413
#2
30
32'
1.2
206
60
34'
1.8
413
4.1
1.86
40
33'
1.4
275
30
36'
2.6
206
2.1
50
34'
1.6
344
29'
3.0
207
40
40'
3.0
275
2.8
60
34'
1.8
413
50
42'
3.4
344
3.4
32'
3.1
275
#4
30
36'
2.6
206
60
42'
3.7
413
4.1
40
40'
3.0
275
35'
3.5
344
30
38'
4.2
206
2.1
50
42'
3.4
344
K
40
43'
60
4.9
42'
275
3.7
2.8
413
37'
3.8
413
50
46'
5.5
344
3.4
14.0
#6
30
38'
4.2
206
Housing
60
47'
6.0
413
4.1
14.3
40
43'
4.9
275
31'
3.4
207
50
46'
5.5
344
40
45'
6.0
275
2.8
Can
60
47'
6.0
413
50
48'
6.8
344
3.4
14.6
34'
3.9
275
60
49'
7.6
413
4.1
14.9
#8
40
45'
6.0
275
70
51'
50
8.2
48'
482
6.8
4.8
344
15.5
37'
4.4
344
60
49'
7.6
413
70
51'
8.2
482
38'
4.7
413
B
Nozzle Retention Screw
D
Nozzle
Turret
C
L
Arc Set Adjustment
C
Key in Keyhole
U.S.
Flow
D
LOW ANGLE NOZZLE PERFORMANCE
PSI
Ft.
GPM
Nozzle
METRIC
U.S.
Flow
Nozzle Pressure Radius
Flow
Turret
Bars
Meters
L/M
M
/H
PSI
Ft.
GPM
3
30
22'
1.2
2.1
11.0
7.6
0.45
#1
30
22'
1.2
2.8
11.6
9.1
0.55
40
24'
1.7
40
24'
1.7
3.4
12.2
10.2
0.61
50
26'
1.8
4.1
12.2
11.0
0.66
60
28'
2.0
2.1
8.5
1.9
0.11
#3
30
29'
3.0
50
26'
1.8
2.8
8.8
2.3
0.14
40
32'
3.1
3.4
8.8
2.7
0.16
50
35'
3.5
4.1
9.1
3.0
0.18
60
37'
3.8
60
28'
2.0
2.1
8.8
2.6
0.16
#4
30
31'
3.4
2.8
9.1
3.0
0.18
40
34'
3.9
3.4
9.1
3.4
0.20
50
37'
4.4
4.1
9.4
3.8
0.23
60
38'
4.7
30
29'
3.0
2.1
9.1
3.4
0.20
#6
40
38'
6.5
2.8
9.4
3.8
0.23
50
40'
7.3
40
32'
3.1
3.4
9.4
4.5
0.27
60
42'
8.0
4.1
9.8
4.9
0.30
70
44'
8.6
2.1
9.8
4.5
0.27
50
35'
3.5
Data represents test results in zero wind for the RPS50 Rotor. A
2.8
10.1
5.3
0.32
Radius may be reduced with nozzle retention screw.
3.4
10.4
6.1
0.36
4.1
10.4
6.8
0.41
60
37'
3.8
2.1
11.0
9.8
0.59
2.8
12.2
11.4
0.68
3.4
12.8
12.9
0.77
4.1
30
12.8
14.0
0.84
31'
3.4
2.1
11.6
15.9
0.91
2.8
13.1
18.5
1.11
40
34'
3.9
3.4
14.0
20.8
1.25
4.1
14.3
22.7
1.36
2.8
13.7
22.7
1.36
50
37'
4.4
3.4
14.6
25.7
1.54
4.1
14.9
28.8
1.73
4.8
15.5
31.0
1.86
60
38'
4.7
40
38'
6.5
50
40'
7.3
60
42'
8.0
70
44'
8.6
Right
Start
Left
LOW ANGLE NOZZLE
Stop
Flow
Nozzle Pressure Radius
LOW ANGLE NOZ
L/M
M
/H
PSI
3
METRIC
11.0
7.6
0.45
#1
30
Flow
Nozzle Pressure Rad
11.6
9.1
0.55
40
12.2
10.2
0.61
50
Bars
Meters
L/M
M
/H
3
12.2
11.0
0.66
60
#1
2.1
11.0
7.6
0.45
8.5
1.9
0.11
#3
30
2.8
11.6
9.1
0.55
8.8
2.3
0.14
40
3.4
12.2
10.2
0.61
8.8
2.7
0.16
50
4.1
12.2
11.0
0.66
METRIC
9.1
3.0
0.18
60
2.1
8.5
1.9
0.11
#3
8.8
2.8
2.6
8.8
0.16
2.3
0.14
#4
30
Flow
9.1
3.4
3.0
8.8
0.18
2.7
0.16
40
4.1
9.1
3.0
0.18
9.1
3.4
0.20
50
9.4
3.8
0.23
60
Bars
Meters
L/M
M
2.1
8.8
2.6
0.16
#4
2.8
9.1
3.0
0.18
9.1
3.4
0.20
#6
40
3.4
9.1
3.4
0.20
9.4
3.8
0.23
50
2.0
4.1
9.4
6.7
3.8
0.23
4.5
.34
9.4
4.5
0.27
60
9.8
2.1
4.9
9.1
0.30
3.4
0.20
#6
70
3.0
7.3
6.4
.39
2.8
9.4
3.8
0.23
9.8
4.5
0.27
3.4
9.4
4.5
0.27
Data represents test results in zero w
3.5
7.9
6.8
.41
10.1
5.3
0.32
4.1
9.8
4.9
0.30
Radius may be reduced with nozzle
10.4
6.1
0.36
4.0
8.5
7.6
.46
2.1
9.8
4.5
0.27
10.4
6.8
0.41
Data represents test results
2.8
10.1
5.3
0.32
11.0
9.8
0.59
Radius may be reduced with
3.4
10.4
6.1
0.36
2.0
8.8
11.4
.68
12.2
11.4
0.68
4.1
10.4
6.8
0.41
12.8
12.9
0.77
3.0
9.8
11.7
.71
2.1
11.0
9.8
0.59
12.8
14.0
0.84
2.8
12.2
11.4
0.68
3.5
10.7
13.2
.80
11.6
15.9
0.91
3.4
12.8
12.9
0.77
13.1
4.1
18.5
12.8
1.11
14.0
0.84
4.0
11.3
14.4
.87
20.8
1.25
2.1
11.6
15.9
0.91
22.7
1.36
2.8
13.1
18.5
1.11
2.0
9.4
12.9
.78
3.4
14.0
20.8
1.25
13.7
22.7
1.36
4.1
14.3
22.7
1.36
25.7
1.54
3.0
10.4
14.8
.89
28.8
1.73
2.8
13.7
22.7
1.36
3.4
31.0
14.6
1.86
25.7
1.54
3.5
11.3
16.7
1.00
4.1
14.9
28.8
1.73
4.8
15.5
31.0
1.86
4.0
11.6
17.8
1.07
Pr
KPa
ME
Pressure Ra
KPa
Bars
Me
207
207
2.0
6
275
3.0
7
275
344
3.5
7
413
4.0
8
207
2.0
8
344
275
3.0
9
344
3.5
10
413
4.0
11
413
207
2.0
9
275
3.0
10
344
3.5
11
413
4.0
11
207
275
3.0
11
344
3.5
12
275
413
4.0
12
482
5.0
13
344
413
207
275
344
413
275
344
413
482
U.S.
F
Ft.
G
U.S.
22'
24'
26'
PSI
Ft
28'
30
22
29'
40
24
32'
50
26
35'
60
28
37'
30
29
40
31'
32
50
34'
35
60
37
37'
38'
/H
3
30
31
40
34
38'
50
37
40'
60
38
42'
40
44'
38
50
40
60
42
70
44
Need help?
Do you have a question about the RPS50 and is the answer not in the manual?
Questions and answers