Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Grundig STR 622 TWIN
Summary of Contents for Grundig STR 622 TWIN
- Page 1 S A T E L L I T E T V R E C E I V E R S T R 6 2 2 T W I N S T R 3 2 2 T W I N...
-
Page 2: Table Of Contents
Finetuning the Reception Frequency GRUNDIG VIDEO CONTROL ....2 on Reception Unit B ..... . 16 Environmental Note . -
Page 3: Useful Information
The GRUNDIG High-End twin receiver has not been preprogrammed, then this can be easily STR 622 TWIN is equipped with two reception done (see chapter “The On-screen Menu Guide” on units A and B. -
Page 4: Grundig Environment Initiative
All large plastic parts are Hand batteries in at appropriate collecting points. marked. Plastic parts from old devices are recycled in GRUNDIG recycling plants and flow back into These operating instructions were printed on recy- production. To facilitate service and for optimum cled paper. -
Page 5: The Receiver At A Glance
STR 622 TWIN POWER TIMER EXIT VIDEO CONTROL INPUT-SAT É 220-240 V~ 950-2150 MHz EURO AV TV EURO AV DECODER EURO AV VCR 50-60 Hz 14/18 V 350 mA AUDIO OUT Rear Side Front Side INPUT B/VCR Connector for satellite aerial Stand-by button. -
Page 6: The Remote Control
TP 820 SAT universal remote control unit. The remote control unit can also be used to control TV sets from GRUNDIG and many other makes (see chapter on “Universal Remote Control” on page 6). Several keys on the remote control have special functions in the menu (see page 11). -
Page 7: Universal Remote Control
23 Thomson old, Model 2 The TP 820 SAT Telepilot supplied can be used to 24 Thomson old, Model 3 control not only the STR 622 TWIN satellite recei- 25 JVC, VCR 1 JVC, Telefunken, … ver, but also many GRUNDIG SAT receivers and 26 JVC, VCR 2 JVC, Telefunken, …... -
Page 8: Connection
TV set via the receiver. means of an F-connector to the screw terminal of the STR 622 TWIN as shown in the figure. A connected decoder is automatically linked (eva- luation of the switching voltage). For decoders that... -
Page 9: How To Connect The Sat Aerial
7). aerial with 2 LNB’s), it is necessary to install a 22 kHz multi-switch (e.g. GRUNDIG SVT 5/4) be- Select the AV programme position on the TV set. tween the receiver inputs A/TV and B/VCR and the two LNB’s (see figure). -
Page 10: Reception Of Four Satellites
620) or they can be found in a satellite maga- Pol./Ant. 0 kHz zine. These frequencies can be reprogrammed via the menu guide. Dual LNBs, e.g. GRUNDIG LNC DUAL 1 Eutelsat 13° Astra Eutelsat 16° Eutelsat 10° 0 kHz, a... -
Page 11: Selecting A Programme Position
(Threshold extension/DX) Use the ]| keys to step through the programme positions, or use the numeric keys to directly enter The STR 622 TWIN is especially suited for the the programme position number. reception of very weak signal. This is accomplished by its integrated three-stage threshold extension ❒... -
Page 12: The On-Screen Menu Guide
General The Menu Items The receiver is already preprogrammed to the cur- Press the key on the remote control unit. MENUE rent stations of many satellites (see Station table). – The main menu is displayed. New stations arrive again and again and station frequencies are changed. -
Page 13: Entering/Changing A Station Name
Pol./Ant. 0 kHz next page. With the STR 622 TWIN you can receive the signals from up to 4 satellites. Copying programme positions For this, you have to choose Hor/Ver, 0/22 kHz and... -
Page 14: Selecting Lnb Oscillator Frequencies
❒ Vorrang (priority) Selecting LNB oscillator frequencies As your receiver has 2 separate reception units but LNB LO: 1 (9750) only 1 decoder socket, the decoder socket has been assigned at the factory to the reception unit A (set- Use the keys to select between 4 preset LO ting: “Decoder: Vorrang A”). -
Page 15: Lnb Power Supply On/Off
❒ LNB power supply on/off LNB Spg. 14/18 V The values of the levels 1 to 3 should only be altered if the programme positions preset with In order to change the LNB power supply setting, these levels require this. The contrast of these pro- press the key when in the “LNB LO”... -
Page 16: Programming Additional Radio Programme Positions
For exceptional cases, the audio settings 24 to 32 In the “Audio BW” (Bandwidth) menu line, the are provided. You can define these settings as sound quality can be optimized. required in a sub-menu which is displayed by pres- sing the key. -
Page 17: Finetuning The Reception Frequency On Reception Unit B
B, press the key to select the MENUE main menu. finetuning function for this programme position. The following menu is displayed: Twin LNB, e.g. GRUNDIG LNC 975/5 TG Programm Name ARD . . Frequenz 11494.0 MHz VIDEO CONTROL INPUT-SAT É... - Page 18 Reception of the high and low frequency satellite with a universal twin LNB ranges of two satellites with ToneBurst switch and quattro LNBs Universal Twin LNB, e.g. GRUNDIG LNC UNI T1 Quattro LNBs e.g. GRUNDIG LNC UNI Q1 VIDEO CONTROL INPUT-SAT É...
-
Page 19: Programming Video Recordings
Stop 22:15 times. 2. Via the VIDEO CONTROL socket, the satellite receiver can be controlled by a GRUNDIG video recorder which is prepared for this function. 0 . . 4 Depending on the video recorder, recording of up TXT = Exit OK = Store to 8 different broadcasts can be programmed. -
Page 20: Sat Recording Control Via A Grundig Video Recorder (Video Control)
Certain video recorders switch the receiver to stand-by after every elapsed Timer time (event), In connection with the Timer of a GRUNDIG video other video recorders do this only after the last recorder which is prepared accordingly, it is possi- Timer event. -
Page 21: Special Functions
Only then the two receivers can separately be controlled. Enter your four-digit security code. You now have access to all programmes until you The remote control mode of the STR 622 TWIN can switch the receiver to stand-by again. be changed as follows: ❒... -
Page 22: Modulator
It is possible to transfer the data stored in one The code number is cleared and the security func- STR 622 TWIN to another STR 622 TWIN. tion deactivated. For this, connect the VIDEO CONTROL sockets of both receivers with a Cinch cable. -
Page 23: Technical Data
2 F-connectors, 75 Ω (SAT aerial inputs A/B) 2 IEC coax sockets, 75 Ω (terrestrial aerial input, modulator out- put). 1 Mains socket 1 Cinch socket for remote control by a GRUNDIG video recorder and for Datalink 2 Cinch sockets (Audio L and R.) Indicators: 3 LED’s: reception units A/B, Timer... -
Page 24: Rectifying Faults Yourself
Fault Possible cause Rectification No power supply Check mains power plug Does not function No picture or sound. EURO-AV cable loose Insert plugs at receiver and TV set TV set not in AV setting Switch TV set to AV Aerial is not aligned to a satellite Align aerial to required satellite (see assembly instructions for aerial) -
Page 25: Menu Overview
RTL 2 Main menu (if reception unit A is selected) PRO 7 3SAT MENUE N-TV SAT 1 Decoder Vorrang A MENUE Norm FBAS Signal Video + Audio LNB LO 1 09,750 GHz pos LNB LO 2 09,750 GHz pos LNB LO 3 10,600 GHz pos MENUE Programm... - Page 26 GRUNDIG AG 90762 FÜRTH – • 21618–941.01 8/43 (GDP) WÜ/NM 2 3 4 5 6 7 8 9...
Need help?
Do you have a question about the STR 622 TWIN and is the answer not in the manual?
Questions and answers