Page 1
Instructions - Parts Plural Component Mixer Manifold 307400R For mixing two component reactive materials with plural component spraying and dispensing equipment. For professional use only. Model 24H002 Series A High Volume Mixer: 1/2 npt fluid outlet; for use in high volume applications, such as airless spray or high solids epoxy.
Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.
Page 4
Comply with all applicable safety regulations. REACTIVE CHEMICALS HAZARD Graco Inc. does not manufacture or supply any of the reactive chemical components that are used in this equipment, and is not responsible for their effects. Because of the vast number of chemicals that could be used, and their varying chemical reactions, the buyer and user of this equipment should de- termine all facts relating to the materials used, including any of the potential hazards involved.
Grounding Installation For assistance in setting up a plural component system, contact your Graco distributor. This will help assure that you select the proper type and size equipment for your job. The equipment must be grounded to reduce the risk of static sparking.
Operation Operation Startup Solvent may channel through viscous fluids and leave a coating of mixed fluid on the inner tube of your hose. The mixer manifold was tested in oil, which was left in to Fig 2 shows the handle in the UP , or closed, position protect the manifold.
Operation Dispensing Pressure Relief Procedure To dispense the resin and hardener, turn on the supply Follow the Pressure Relief Procedure whenever pumps. Then push the handle forward (DOWN) to the you see this symbol. open position. To stop the flow, move the handle to the UP or closed position.
Troubleshooting Troubleshooting 1. Relieve the pressure before you check or service any system equipment. 2. Check all possible causes and solutions in the Troubleshooting Chart before disassembling the manifold. Problem Cause Solution Little or no resin (A) output The fluid inlet is plugged. Clean the inlet, remove the obstruction.
Service Service Manifold Repair Ball Valve Repair NOTE: Repair Kit 217560 is available for the ball valves. Parts included in the kit are indicated with an asterisk, for example (18*). See page 11. When reassembling a ball valve (13 or 24), install the NOTE: Repair kits are available for the manifold.
Parts Parts Ref No. 13 Ball Valve 215622, Series B Ref No. 24 Low Volume Ball Valve 215623, Series B High Volume 32‡ 33‡ 05769 34‡ 33‡ 05768 13 or 24 Model 24H002 Manifold, Series A Instruction label covers parts 7 and 8 when assembled.
Page 11
Parts Model 24H002, Series A Ref. Part Description Qty. Ref. Part Description Qty. 215623 VALVE, ball; used in model 100721 PLUG, internal hex; 1/4; 1/4 npt 24H002 Series B includes items 104472 CAPSCREW, hex hd; 10–32 x 25–34 1–1/2 102310 .
Parts Model 241692 Series A 5765B Ref. Part Description Qty. Ref. Part Description Qty. 156823 UNION, swivel 24H002 MANIFOLD, mixer; see full parts 108233 VALVE, needle and listing on pages 10 and 11 502265 BUSHING, reducer, pipe 157676 UNION, swivel, 90 512506 MIXER, static, pipe 155699...
Technical Specifications Technical Specifications Plural Component Mixer Manifold Metric Maximum working pressure 3000 psi 21.0 MPa, 210 bar Fluid Port Size Model 241692 1/2 npt(f) Model 24H002 3/8 npt(m) Solvent Port Size Model 24H002 and 241692 1/4 npt(m) Fluid Outlet Size Model 241692 3/8 npt(m) Model 24H002...
With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.