Advertisement
– Duct to the outside atmosphere using the shortest duct run possible
– Always use correctly sized ducting – DO NOT reduce the size of the ducting
– Use cylindrical ducting whenever possible
– Always use solid ducting
– Always use non-flammable ducting
– Always duct to the outside atmosphere
– Do not use flexible ducting
– Do not duct into the ceiling space- always vent to the outside atmosphere.
Installation heights
– Avoid sharp 90 degree bends as much as possible, use 45 degree bends
instead wherever possible
– Over gas and electric cookers, Residentia Group recommends our
– Duct to the outside atmosphere using the shortest duct run possible
rangehoods to be mounted at a height of between 600-800mm above the
Installation Instructions (Continued)
– Use cylindrical ducting whenever possible
cooking surface.
– Electric cooktops must have a minimum height of 600mm from the
underside of the rangehood to the cooktop face.
– Gas cooktops must have a minimum of 650mm from the burner to the
Installation heights
underside of the rangedhood.
– Over gas and electric cookers, Residentia Group recommends our
– Over open flame grillers or barbecues, the Gas Regulations require the
INSTALLATION STEPS
rangehoods to be mounted at a height of between 600-800mm above the
filters of the rangehood to be at least 1200mm above the cooking surface.
cooking surface.
• Drill 4×8mm holes to accommodate the
– Electric cooktops must have a minimum height of 600mm from the
bracket. Screw and tighten the bracket onto
underside of the rangehood to the cooktop face.
– Gas cooktops must have a minimum of 650mm from the burner to the
the wall with the screws and wall plugs
underside of the rangedhood.
–
provided.
– Over open flame grillers or barbecues, the Gas Regulations require the
filters of the rangehood to be at least 1200mm above the cooking surface.
–
WALL BRACKET
–
• Lift up the cooker hood and hang onto the
wall bracket.
–
WALL BRACKET
8
8
• Ensure the screws are secure and the hood is
I N S TA L L AT I O N I N S T R U C T I O N S
SCREW PLUG
SCREW
(4mm x 30mm)
• Fix the one-way valve to the air outlet of the
COOKER HOOD
Chimney installation
Chimney installation
12
I N S TA L L AT I O N I N S T R U C T I O N S
C O N T I N U E D
stable on the wall. After hanging the cooked
hood on the bracket, remove the filters, mark
and drill 2 holes and faster the hood onto the
wall with 2 wall plugs and 2 2 x ST4 × 30mm
C O N T I N U E D
– We need the secure screws to make sure the hood is stable on t
screws.
After hanging the cooker hood on the bracket ,remove the filters
and drill 2 holes and fasten the hood on the wall with 2 wall plugs
× ST4 × 30mm screws.
– We need the secure screws to make sure the hood is stable on the w
After hanging the cooker hood on the bracket ,remove the filters , m
and drill 2 holes and fasten the hood on the wall with 2 wall plugs and
× ST4 × 30mm screws.
– Fix the one-way-valve to the air outlet of the cooker hood. Then,
two exhaust pipes onto the one-way-valve as shown below.
cooked hood. Then, attach two exhaust pipes
onto the one-way valve as shown below.
– Fix the one-way-valve to the air outlet of the cooker hood. Then, atta
two exhaust pipes onto the one-way-valve as shown below.
– Put the upper chimney into lower chimney .
Mark and drill 4 holes depend on the plate I. Fasten the lower chi
the wall with 4 wall plugs and 4×ST4×30mm screws.
– Put the upper chimney into lower chimney .
Mark and drill 4 holes depend on the plate I. Fasten the lower chimne
the wall with 4 wall plugs and 4×ST4×30mm screws.
Advertisement
