HEAT GLO CERONA-36-IFT Installation Manual

Installation and appliance setup
Table of Contents

Advertisement

Quick Links

CAUTION! Risk of Fire! DO NOT store instruction manuals inside appliance cavity.
High temperatures could cause a fire.
INSTALLER: Leave this manual with the appliance, not inside the appliance.
CONSUMER: Retain this manual for future reference. Do not store inside the appliance.
NOTICE: DO NOT discard this manual!
Model(s):
This appliance may be installed as an OEM
installation in manufactured home (USA
only) or mobile home and must be installed
in accordance with the manufacturer's
instructions and the Manufactured Home
Construction and Safety Standard, Title 24
CFR, Part 3280 in the United States, or the
Standard for Installation in Mobile Homes,
CAN/CSA Z240 MH Series, in Canada.
This appliance is only for use with the type(s)
of gas indicated on the rating plate. This
appliance is not convertible for use with other
gases, unless a certified kit is used.
Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21
Installation Manual
Installation and Appliance Setup
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
• DO NOT store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Leave the building immediately.
- Immediately call your gas supplier from
a neighbor's phone. Follow the gas sup-
plier's instructions.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
DANGER
DO NOT TOUCH GLASS
NEVER ALLOW CHILDREN
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and must be installed for
the protection of children and other at-risk
individuals.
Decorative barrier front must be ordered separately.
HOT GLASS WILL
CAUSE BURNS.
UNTIL COOLED.
TO TOUCH GLASS.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CERONA-36-IFT and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for HEAT GLO CERONA-36-IFT

  • Page 1 Decorative barrier front must be ordered separately. Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 2: Table Of Contents

    E. Prepare For Heat Management ....29 Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 3: Installation Standard Work Checklist

    _____________________________________________________________________________________ _________________________________________________________________________________________________ _________________________________________________________________________________________________ Comments Communicated to party responsible ____________________ by ______________________on ___________ (Builder / Gen. Contractor/) (Installer) (Date)  = Contains updated information. 2558-982 11/20 Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 4: Product Specific And Important Safety Information

    State of California to cause cancer and reproductive harm. For more information go to: www. P65Warnings.ca.gov. Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 5: Requirements For The Commonwealth Of Massachusetts

    VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OB- of the installation. STRUCTIONS”. See Gas Connection section for additional Common- wealth of Massachusetts requirements. Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 6: Getting Started

    Use appropriate finishing materials that are able to withstand these conditions. For additional finishing guidelines, see Section 10. Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 7: Tools And Supplies Needed

    • Improper positioning of the logs/media (as applicable) or the glass assembly. • Installation and/or use of any component part not approved by Hearth & Home Technologies. Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 8: Framing And Clearances

    35-7/8 35-3/8 33-7/8 14-1/4 39-1/2 1003 17-3/4 6-5/8 12-1/2 6-3/4 12-5/8 34-1/2 38-5/8 49-7/8 1268 9-1/8 1372 9-1/8 2-1/4 6-1/4 2-1/4 7-3/4 Figure 3.1 Appliance Dimensions Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 9 1-1/8 IN. 39-1/8 IN. 1-1/8 IN. (851 mm) (994 mm) (29 mm) (29 mm) 37-1/2 IN. 43-1/8 IN. (953 mm) (1095 mm) Figure 3.2 Decorative Front Dimensions Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 10: Appliance Location And Clearances To Combustibles

    42-1/8 73-1/4 65-1/2 22-1/4 Millimeters 1295 1070 1861 1664 CERONA-42-IFT Inches 56-5/8 49-1/8 80-1/8 72-1/2 22-1/4 18-3/4 Millimeters 1438 1248 2035 1842 Figure 3.3 Appliance Locations Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 11 Note: If appliance is installed off of floor, maintain required clearances to combustibles. Construct platform in accordance with local building codes. Figure 3.4 Clearances to Combustibles  Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 12 ** Measurement without Trim Kit = 2 in. + Additional Finishing Material Thickness. If finished discharge opening height is greater than 3 inches, wire mesh is required. Figure 3.5 Passive Heat Front Discharge Framing Dimensions With and Without a Trim Kit Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 13 Materials Inches 12-1/4 8-3/4 70-1/4 CERONA-36-IFT millimeters 1784 2134 Inches 12-1/4 8-3/4 74-3/8 88-1/8 CERONA-42-IFT millimeters 1889 2238 Figure 3.6 Passive Heat Side Discharge Framing Dimensions Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 14 Mesh screen required for front discharge or open top discharge passive heat installations with discharge opening of 3 inches or greater. Figure 3.7 Passive Heat Minimum Framing Dimensions Open Top Discharge Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 15: Constructing The Appliance Chase

    Minimum height requirements for an exterior chase on a top- vented appliance are shown in Figure 3.8. Reference Figure 4.4 for additional clearances. Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 16: Termination Location And Vent Information

    Over 20/12 to 21/12 ..........8.0 * H minimum may vary depending on regional snowfall. Refer to local codes. Figure 4.1 Minimum Height From Roof to Lowest Discharge Figure 4.3 Opening Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 17: Vent Terminal Clearances

    12 in. (305 mm)* two sides beneath the floor.) vinyl or composite overhang 42 in. (1067 mm) 42 in. (1067 mm) Figure 4.4 Minimum Clearances for Termination Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 18: Use Of Elbows

    Figure 4.6 Vertical and Horizontal Offset for DVP DVP36 25-1/2 DVP48 1219 DVP6A 3 to 6 76 to 152 2-1/8-4-1/4 54-108 DVP12A 3 to 12 76 to 305 2-1/8-8-1/2 54-216 Figure 4.5 Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 19: Adding Vent Components

    1 inch airspace between the shield and the combustible surface. See Figure 4.10. CORRECT INCORRECT COMBUSTIBLE SURFACE DIRECTION HEAT SHIELD 90º ELBOW Figure 4.8 Fiberglass Rope Ring Figure 4.10 Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 20: Install Support Brackets

    (2) sheet metal screws. F. Install Support Brackets Refer to Cinch Pipe and Termination Cap installation in- structions. Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 21 Clearance to Trapezoid Portion of Cap MEASURE TO SHADED SURFACE (OUTSIDE MOUNTING SURFACE) Figure 4.12 Measure to Outside Mounting Surface Figure 4.13 Measure to Top of Last Section of Pipe Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 22 Model cal vent before CERONA-36-IFT attaching a 90º e l b o w t o t h e CERONA-42-IFT unit. See chart. Figure 4.16 Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 23 Straight up Vertical Venting Note: On vertical venting configurations install the flue restrictor found in the appliance manual bag. Follow flue restrictor instructions in Section 6.D. Figure 4.18 Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 24 Model cal vent before CERONA-36-IFT attaching a 90º e l b o w t o t h e CERONA-42-IFT unit. See chart. INSTALLED HORIZONTALLY Figure 4.20 Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 25: Vent Clearances And Vent Framing

    1778 mm Note: Center of the horizontal vent pipe to the vertical measuring surface of a trap cap is 5 inches (127 mm) Figure 5.2 Wall Penetration Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 26: Ceiling Firestop/Floor Penetration Framing

    INSTALL ATTIC INSULATION SHIELDS BEFORE OR AFTER INSTALLATION OF VENT SYSTEM CEILING FIRESTOP CEILING FIRESTOP INSTALLED BELOW CEILING INSTALLED ABOVE CEILING Figure 5.4 Installing the Attic Shield Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 27: Appliance Preparation

    • Discard brackets. • Replace screws in holes where these pieces were NAILING TABS attached to appliance. Figure 6.2 Proper Positioning, Leveling and Securing of a Appliance Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 28: Installing Non-Combustible Facing Material

    • Apply a non-combustible adhesive to attach tile, stone or other non-combustible finishing materials per manufacturer’s instructions. Figure 6.3 Attaching Non-combustible Facing Material Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 29: Installing Flue Restrictor

    WARNING! RISK OF FIRE! If only one heat manage- ment option is being used, the unused knockout must remain in place. Overheating of combustible materials will occur. Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 30: Venting

    • Only outer pipes need to be sealed. All unit collar, pipe, Lances Lances slip section, elbow and cap outer flues shall be sealed in this manner, unless otherwise stated. Figure 7.3 Figure 7.2 Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 31: Assemble Slip Sections

    “Assembling Pipe Sections.” NOTICE: If slip section is too long, the inner and outer flues of the slip section can be cut to the desired length. Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 32: Secure The Vent Sections

    • SLP ceiling firestops have tabs that may be used to provide vertical support. Figure 7.9 Rotate Seams for Disassembly 120º Figure 7.7 Securing Vertical Pipe Sections Figure 7.10 Align and Disassemble Vent Sections Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 33: Vertical Termination Requirements

    Slide the storm collar onto the exposed pipe section and align brackets. • Insert a bolt (provided) through the brackets and install nut. Do not completely tighten. Figure 7.13 Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 34: Horizontal Termination Requirements

    • When installing a horizontal termination cap, follow the cap location guidelines as prescribed by current ANSI Z223.1 and CAN/CGA-B149 installation codes and refer to Section 4 of this manual. Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 35: Electrical Information

    Romex connector. See Figure 8.1. • Make all necessary wire connections to the junction box/ receptacle and reattach the junction box/receptacle to the outer shell. Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 36 IFT-ECM REAR PLACEMENT TAB IFT-ECM POWER SUPPLY GUIDE IFT-ACM POWER SUPPLY GREEN/WHITE/BLACK WIRES RF MODULE WIRE HARNESS IFT-ACM IFT-ECM FRONT PLACEMENT TAB Figure 8.2 Electrical Component Tray Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 37: Wiring Requirements

    (OPTIONAL) RF MODULE CONTROL LIGHT TUB ASSEMBLY 6V DC APPLIANCE ON/OFF USB-C WIRE BATTERY PACK CONTROL BRN BLK ASSEMBLY (OPTIONAL) Figure 8.3 IntelliFire Touch Wiring Diagram Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 38: Gas Information

    • If substituting for these components, please consult Check with your local gas utility to determine proper local codes for compliance. orifice size. Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 39: Air Shutter Setting

    If flames are dark orange with dark, smoky tips, provide more primary air to the burner by opening the air shutter accordingly. Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 40: Finishing

    NOT be used as sheathing or facing in the non-combustible zone. • See Section 3 for proper clearances. • See Section 1 for combustible/non- combustible definitions. Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 41: Finishing Material Options

    Note: See Section 3 (Figure 3.2) for decorative front RESTRICTOR dimensions. TABS - BENT Figure 10.4 Restrctor Tabs Bent Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 42: Hearth Extension

    UNDER THE OPENING BOTTOM OF APPLIANCE Figure 10.9 Appliance Raised a Minimum of 6 Inches Away from Combustible Surface. Figure 10.7 Top and Arch Finishing Pieces Assembled Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 43: Mantel Projections

    25 76 102 127 152 178 203 229 254 279 ∞ Figure 10.13 Clearances to Mantel Legs or Wall Projections (Acceptable on both sides of opening.) Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 44 32-1/2 16-3/4 16 CERONA-36-IFT 406 432 1245 28-1/2 16-3/4 16 17 45-1/4 CERONA-42-IFT 406 432 1149 Figure 10.15 Clearances to mantels or other non-combustibles above appliance Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 45: Appliance Setup

    3 to 5 applications. See Figure 11.1. GLOWING EMBER PLACEMENT Figure 11.2 Placement of Embers Figure 11.1 Surface plane of firebox is compromised and should be replaced. Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 46: Positioning The Logs

    It may be necessary to tilt Log portion of log #2. See Figure 4. #1 forward to properly engage with Log #2. See Figure 3. Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 47 LOG #6 (SRV2106-706): Rest bottom notch of log #6 on the grate tine and the top part on formed section of log #5 (A). See Figure 7. Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 48 (A). See Figure 4. log on the flat section of log #1. See Figure 3. Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 49 #5 and the flat on log #3. You may need to reposi- tion log #5 to get log #6 to sit in the flats. See Figure 7. Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 50: Intellifireā„¢ Touch Control System Setup

    For more information refer to the instructions supplied with your decorative barrier front. Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 51: Reference Materials

    6 in. 14 IN. (152 mm) (356 MM) 12 IN. (305 MM) DVP-WS (Wall Shield Firestop) DVP-RDS ROOF DECK INSULATION SHIELD Figure 12.1 DVP Vent Components Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 52 79 mm 117 mm Horizontal Termination Cap 5-3/8 in. 9-3/8 in. Trap2 137 mm 238 mm DVP-TRAP2 DVP-TRAP1 DVP-TRAPK2 DVP-TRAPK1 DVP-HPC2 DVP-HPC1 Figure 12.2 DVP Vent Components Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 53 9-1/2 in. (352 mm) (241 mm) 26 in. 660 mm 14 in. (356 mm) DVP-HSM-B DRC-RADIUS Extended Heat Shield Cap Shield Figure 12.3 DVP Vent Components Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 54 High Performance Cap 12 in. 305 mm 7-1/4 in. (184 mm) 12-1/2 in. (318 mm) 5-1/4 in. (133 mm) DVP-TVHW VerticalTermination Cap (Highwind) Figure 12.4 Vent Components Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 55 Only use listed decorative termination caps/shrouds with Hearth & Home Technologies approved venting systems. This applies to both DVP and SLP venting systems. Decorative Terminations Caps/Shrouds DTO134 DTO146 DTS134 DTS146 LDS33 LDS46 LDS-BV Figure 12.5 DVP Vent Components Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 56 424 mm (424 mm) 12-1/2 IN. (318 mm) SLP-LPC SLP Low Profile Cap (Approved for use with PVI-SLP-B only) DVP-2SL Adapter Figure 12.6 PVI-SLP-B Vent Components Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 57 60 FT PV Wire Harness PVI-WH60 80 FT PV Wire Harness PVI-WH80 100 FT PV Wire Harness PVI-WH100 PVLP-HS PVLP-BEK Heat Shield Brick Kit Figure 12.7 PVLP-SLP Vent Components Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 58 Option B: IFT-RC150, IFT-ACM, IFT-WFM and an IntelliFire App that can be downloaded from the app store. These accessories are purchased separately from the PVV-SLP. Contact your dealer to order. Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...
  • Page 59: Accessories

    Please contact your Heat & Glo dealer with any questions or concerns. For the location of your nearest Heat & Glo dealer, please visit www.heatnglo.com. Printed in U.S.A. - Copyright 2021 Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21...

This manual is also suitable for:

Cerona-42-ift

Table of Contents