Place the BIPAC-711C2 / 710C2 on a stable surface. Only use the power adapter that comes with the package. Using a different voltage rating power adaptor may damage the router. Attention Billion BIPAC – 711C2 / 710C2 – ADSL Modem / Router...
Quick Start Guide The Front LEDs ADSL The difference between BIPAC-711C2 and 710C2 is that BIPAC-710C2 does not have USB port; the rest functions are the same as BIPAC- 711C2. Lit green when power adapter is connected. When lit, it indicates that the device is working properly. When this LED is lit, it indicates that the USB port is connected to the PC and working properly.
RESET (USB connector) LINE (RJ-11 connector) Billion BIPAC – 711C2 / 710C2 – ADSL Modem / Router Power ON/OFF switch Connect the supplied power adapter to this jack. Connect the supplied crossover cable to this port when connecting to a NIC (Network Interface card) in PC.
Page 6
Quick Start Guide Connecting Your ADSL Modem/Router Through Ethernet Port 1. Connect the Router to a LAN (Local Area Network) and the ADSL/telephone (LINE) network. 2. Power on the device. 3. Make sure the PWR, SYS and LAN LEDs are lit steadily 4.
2. Insert the installation CD into the CD-ROM drive. Check “Search removable media” and click “Next >”. Then, it takes seconds to search and install the software. Billion BIPAC – 711C2 / 710C2 – ADSL Modem / Router (for BIPAC-711C2 only)
Page 8
Quick Start Guide 3. When windows titled “Hardware Installation” or “Software Installation” appear, press “Continue Anyway” to go on. 4. Then, click “Finish” 5. After a few moments, Windows will show the new device, USB ADSL Adapter, has been detected. Select “Install from a list or specific location”. Click “Next >”.
Page 9
Billion BIPAC – 711C2 / 710C2 – ADSL Modem / Router 6. Click “Next >” when the following figure appears. 7. When windows titled “Hardware Installation” appears, press “Continue Anyway”. Then, click “Finish” to end installation. 8. After installing the driver, follow the next section to configure the network properties on the PC.
Quick Start Guide Configuring PC in Windows XP 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on Network Connections 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window, click Properties. 4.
Properties. 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration. Billion BIPAC-711C2/710C2 ADSL Modem / Router...
Quick Start Guide Configuring PC in Windows 98/Me 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2. Select TCP/IP -> NE2000 Compatible, or the name of your Network Interface Card (NIC) in your PC.
Page 13
1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties. 3. Select the Obtain an IP address from a DHCP server radio button and click OK. Billion BIPAC-711C2/710C2 ADSL Modem / Router...
Page 14
Quick Start Guide Configuring Your ADSL Modem/Router To configure this device, you must have IE 5.0 / Netscape 4.5 or above installed Verifying Your Local Network Connection with the Device To see if this ADSL Router is visible on the local network, go to Start / Run.
Need help?
Do you have a question about the BiPAC 710C2 and is the answer not in the manual?
Questions and answers