Subscribe to Our Youtube Channel
Related Manuals for adstec IPC9000 Series
Summary of Contents for adstec IPC9000 Series
- Page 1 Translation of the original instruction manual Version 1.1 Instruction manual Industrial PCs IPC9000 Serie Updated 2021-04-29...
- Page 2 IPC9000 Serie − Instruction manual v1.1 Read these instructions carefully before using and store for future reference. These instructions contain important information about the product, in particular about its intended use, safety, installation, utilisation, maintenance and disposal. Hand over the instructions to the user following installation of the product, and pass the manual on to the new user if the product is resold.
-
Page 3: Table Of Contents
IPC9000 Serie − Instruction manual v1.1 Contents General information about documentation ................5 General information Explanation of safety instructions 1.2.1 Structure of safety instructions 1.2.2 Explanation of signal words Relevant device documentation Symbols Data, figures and modifications Trademarks Copyright General device information ...................... 9 Manufacturer and contact details Intended use Improper use... - Page 4 IPC9000 Serie − Instruction manual v1.1 Features (optional) ......................... 24 Big-LinX ® DisplayPort™ HDBaseT™ CAN card RAID system WLAN Bluetooth™ netJACK plug-in modules Wake on LAN (WoL) 7.9.1 Settings in BIOS 7.9.2 Settings in the operating system (Windows 10) Software / driver installation ....................32 Initial installation of the operating system Write protection Cleaning ..........................
-
Page 5: General Information About Documentation
IPC9000 Serie − Instruction manual v1.1 1 General information about documentation 1.1 General information This instruction manual is intended to ensure safe and efficient handling of the IPC9000, referred to in the following as "device". All of the safety instructions and handling instructions given in the manual must be obeyed in order to ensure that work is carried out safely. -
Page 6: Explanation Of Signal Words
IPC9000 Serie − Instruction manual v1.1 1.2.2 Explanation of signal words DANGER Indicates an imminent danger. If not avoided, death or severe injury will result. WARNING Indicates a possible danger. If not avoided, death or severe injury could result. CAUTION Indicates a possible danger. -
Page 7: Relevant Device Documentation
IPC9000 Serie − Instruction manual v1.1 1.3 Relevant device documentation The following documents are decisive to device setup and operation: • This instruction manual: contains information for installation, commissioning and operation of the device along with technical data. • Website: You can download the instruction manual as well as drivers, software, user manuals, leaflets and flyers from the Download area of our website www.ads-tec.de. -
Page 8: Trademarks
IPC9000 Serie − Instruction manual v1.1 1.6 Trademarks It is noted that any software and/or hardware trademarks and any company brand names mentioned in this documentation are all subject to the general trademark protection rights. Big-LinX and X-Remote are registered trademarks of ADS-TEC. ®... -
Page 9: General Device Information
IPC9000 Serie − Instruction manual v1.1 2 General device information 2.1 Manufacturer and contact details The manufacturer of the device is ads-tec Industrial IT GmbH. The company is referred to in the following as ADS-TEC. ads-tec Industrial IT GmbH Heinrich-Hertz-Str.1 72622 Nürtingen Germany Phone: +49 7022 2522-0... -
Page 10: Improper Use
IPC9000 Serie − Instruction manual v1.1 2.3 Improper use Operation other than or beyond that described for the device shall be deemed improper use. The device is not allowed to be used to control vehicles or for applications for which further approvals beyond the manufacturer's declaration are necessary, e.g. -
Page 11: Environmental Conditions
IPC9000 Serie − Instruction manual v1.1 2.4 Environmental conditions ATTENTION Damage caused by heat! If the device is exposed to sunlight or any other light or heat source, it can overheat and suffer damage. Do not expose the device to direct radiation by sunlight or any other light or heat source! ATTENTION Damage caused by heat! If the device is installed in a panel, casing or similar, heat accumulation can occur. -
Page 12: Conformity
IPC9000 Serie − Instruction manual v1.1 2.5 Conformity The manufacturer hereby declares that the product described in this instruction manual complies with all relevant stipulations of the following European directives: • 2011/65/EU, RoHs Directive • 2014/30/EU, EMC Directive • 2014/53/EU, RED Directive •... -
Page 13: Warranty / Repairs
IPC9000 Serie − Instruction manual v1.1 2.6 Warranty / repairs During the device warranty period, any repairs must only be performed by the manufacturer or by service personnel that has been authorised by the manufacturer. 2.7 Limitation of liability ADS-TEC shall not be liable for personal injury, property damage or damage caused to the device as well as consequential damage that is/was the result of non-compliance with this instruction manual, improper use of the device, repairs and other actions on the device by unqualified electricians and electricians not certified by ADS-TEC, or that is/was the result of using unapproved replacement parts. -
Page 14: Treatment And Disposal Of Lithium Batteries
IPC9000 Serie − Instruction manual v1.1 2.8 Treatment and disposal of lithium batteries WARNING Hazard due to explosion Danger of explosion if using incorrect battery types. Use the battery type recommended by the manufacturer. ATTENTION Hazard due to thermal loads The more the battery is exposed to higher temperatures, the faster it ages. -
Page 15: Scope Of Delivery
IPC9000 Serie − Instruction manual v1.1 3 Scope of delivery Check that the contents of the package are intact: If there are signs of damage, please contact the manufacturer immediately. The device must not be put into operation. Check that the contents of the package are complete and match your order: 1 x device −... -
Page 16: Mechanical Installation
IPC9000 Serie − Instruction manual v1.1 4 Mechanical installation The device is intended to be fastened to a screw-on wall bracket (included in the scope of delivery). The device is not intended for installation on top-hat rails. 4.1 Requirements Make sure that the attachment surface can safely bear the weight of the device under all operating conditions. -
Page 17: Attaching The Device To The Wall Bracket
IPC9000 Serie − Instruction manual v1.1 4.3 Attaching the device to the wall bracket 1. Hang the rear side of the device on the top of the wall bracket. 2. Push the bottom of the device backwards until it locks into place. ©... -
Page 18: Removing The Device From The Wall Bracket
IPC9000 Serie − Instruction manual v1.1 4.4 Removing the device from the wall bracket 1. Pull downwards on the pull tab on the bottom rear of the device (use fingers or screwdriver). 2. Pull the device upwards off the wall bracket. ©... -
Page 19: Electrical Connections
IPC9000 Serie − Instruction manual v1.1 5 Electrical connections 5.1 Requirements ATTENTION Damage due to electrostatic discharge! Damage to the device can be caused by electrostatic discharge. Always adhere to the safety measures applicable when handling components at risk of being •... -
Page 20: Interface Overview
IPC9000 Serie − Instruction manual v1.1 5.2 Interface overview Example illustration. Position assignments may differ depending on the version: Description Slot for Big-LinX smart card, see section 7.1 ® Protective earth (PE) connection, see section 5.2.2 Options at this position: HDBaseT (RJ45), see section 7.3 −... -
Page 21: Power Supply
IPC9000 Serie − Instruction manual v1.1 5.2.1 Power supply +24 VDC ± 20 % Functional earth Reference potential (The figure shows the socket inside the device) Digital input 24 VDC Digital output 24 VDC Conductor cross sections: V+ / FE / 0V: AWG 18 (≙ 0.75 mm Digital output: type 3 according to IEC61131 (no self-diagnostic function) 0 signal = 0 V, 1 signal = 24 VDC, max. -
Page 22: Can Interface
IPC9000 Serie − Instruction manual v1.1 5.2.3 CAN interface The optional CAN bus card features two separate CAN buses connected together via a 9-pin Sub-D connector. The connector on the power supply line assembled by the customer must have the following pin assignment: Signal n.c. -
Page 23: Commissioning
IPC9000 Serie − Instruction manual v1.1 6 Commissioning 6.1 Requirements ATTENTION Hazard due to condensation Damage to electronic components caused by condensation resulting from temperature fluctuations. Switch on the device only after it has acclimated to the ambient temperature. • 6.2 Switching on and configuring device After connecting the power supply and monitor, the device can be started using the ON/OFF button on top of the device. -
Page 24: Features (Optional)
IPC9000 Serie − Instruction manual v1.1 7 Features (optional) 7.1 Big-LinX ® Big-LinX is a versatile and scalable IoT service platform which provides high-performance modular solutions for different IoT applications. The secure connection of decentralised systems, the management of distributed gateways as well as comprehensive services for data collection, forwarding and monitoring make a major contribution to the implementation of complex Industry 4.0 projects. -
Page 25: Hdbaset
IPC9000 Serie − Instruction manual v1.1 7.3 HDBaseT™ HDBaseT™ makes it possible to transmit data to a monitor up to 100 m away. The connection between the transmitter and receiver is made using a LAN cable with RJ45 connector. Recommendation for use: The following cables are recommended for connecting the transmitter module to the receiver module: CAT6a cable 100 m with min. -
Page 26: Can Card
IPC9000 Serie − Instruction manual v1.1 7.4 CAN card The optional CAN bus card from PEAK features two separate CAN buses connected together via a 9- pin Sub-D connector. The two buses are galvanically isolated from each other and from the device’s electrical system. -
Page 27: Raid System
IPC9000 Serie − Instruction manual v1.1 7.5 RAID system The device supports two separate SSD mass storage devices that can be used together with the help of RAID technology (RAID = redundant array of independent disks). To use this function, two type M.2 2242 Key M SSD cards with a SATA interface are required. NVMe cards with a PCIe interface cannot be used. -
Page 28: Netjack Plug-In Modules
IPC9000 Serie − Instruction manual v1.1 7.8 netJACK plug-in modules The netJACK plug-in modules from Hilscher make it possible to connect the device with all common fieldbus and real-time Ethernet systems, such as PROFIBUS DP, PROFINET IO, CANopen ® ® ®... -
Page 29: Wake On Lan (Wol)
IPC9000 Serie − Instruction manual v1.1 7.9 Wake on LAN (WoL) This function can be used for event-driven startup of "sleeping" computers on the local network, such as for running updates at night. The interfaces LAN1 … LAN 3 are available for this purpose: The computer must be in one of the following ACPI states in order to wake up via WoL: State S5: computer is shut down, voltage is present... -
Page 30: Settings In The Operating System (Windows 10)
IPC9000 Serie − Instruction manual v1.1 7.9.2 Settings in the operating system (Windows 10) In Device Manager under "Network adapters", open the properties dialogue box of the Ethernet controller for the LAN connector being used (the example here is for LAN1): Make the following settings on the "Advanced"... - Page 31 IPC9000 Serie − Instruction manual v1.1 3. Disable "Wake on Link Settings": 4. On the Power Management tab: "Allow this device to wake the computer": © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany...
-
Page 32: Software / Driver Installation
IPC9000 Serie − Instruction manual v1.1 8 Software / driver installation 8.1 Initial installation of the operating system The device will be delivered with a pre-installed operating system depending on what the customer wants. If the mass storage has been reformatted, the operating system can be reinstalled by using one of the existing interfaces. -
Page 33: Maintenance
IPC9000 Serie − Instruction manual v1.1 10 Maintenance 10.1 Opening and closing the service slot ATTENTION Damage due to electrostatic discharge! Damage to the device can be caused by electrostatic discharge. • Always adhere to the safety measures applicable when handling components at risk of being damaged by electrostatic discharge. -
Page 34: Replacing The Bios Battery
IPC9000 Serie − Instruction manual v1.1 10.2 Replacing the BIOS battery The BIOS battery has a life cycle of 3-5 years depending on the load applied. Recommendation for use: To prevent unexpected plant downtime, as a precaution, the BIOS battery should be replaced within the scope of the maintenance plan (e.g. -
Page 35: Installing Or Removing Ssd Cards
IPC9000 Serie − Instruction manual v1.1 10.3 Installing or removing SSD cards Format: SSD cards with the format M.2 2242 Key M can be used. Interface: depending on the slot, SATA or NVMe cards can be used (see figure below). Compatible mass storage cards can be obtained from ADS-TEC if required. -
Page 36: Dimensional Drawings
IPC9000 Serie − Instruction manual v1.1 11 Dimensional drawings 11.1 Device © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 37: Wall Bracket
IPC9000 Serie − Instruction manual v1.1 11.2 Wall bracket © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 38: Technical Data
IPC9000 Serie − Instruction manual v1.1 12 Technical data Housing Fanless die-casting aluminium housing, powder-coated Processors Intel Celeron 4305UE 2.0 GHz Dual Core ® ® Intel Core i5 8365UE 1.6 GHz Quad Core ® Up to 32 GB DDR4 RAM Mass storage 1 x 128 GB M.2 SSD 1 x 256 GB M.2 SSD... -
Page 39: Service & Support
IPC9000 Serie − Instruction manual v1.1 13 Service & support ADS-TEC and its partner companies offer you comprehensive maintenance and support services, ensuring quick and competent support should you have any questions or concerns with regard to ADS- TEC products and equipment. Because ADS-TEC products are also used by partner companies, these devices may have customised configurations.
Need help?
Do you have a question about the IPC9000 Series and is the answer not in the manual?
Questions and answers