Assa Abloy Code Handle Fitting And Operating Instructions page 9

• Batteries should be kept out of the reach
of children.
• Batteries should be fitted individually.
Security
If an incorrect code is entered five times consecutively,
the code handle will be disabled for 3 minutes and
cannot be opened. The disable can be overridden by
entering a correct code twice consecutively.
User codes
ASSA ABLOY Code Handle can have 9 different user
codes that can be programmed from the selected
administrator's code.
Enter new or change existing user code
1 Enter programming mode by holding the lock
button pressed until the LED lights red constantly.
2 Enter the administrator's code within 5 seconds.
The LED lights green.
3 To register a code, select one of the 9 memory
positions by pressing pushbutton 1 the same number
of times as the memory position; i.e. one depression
for memory 1, two for memory 2, etc.
4 Wait until the LED lights green constantly.
5 Enter the new user code, which can comprise 4, 5
or 6 digits.
6 Wait until the green LED goes out. Your new code is
acknowledged by three short beeps.
7 Other codes can be stored in the remaining
memory positions. Follow the steps 1 - 6 above.
8 To exit programming mode, and confirm your new
codes, press lock button.
NOTE! You can write down your user codes on
page 26.
Remove existing user code:
1 Enter programming mode by holding the lock
button pressed until the LED lights red constantly.
2 Enter the administrator's code within 5 seconds, the
LED lights green.
3 Select which one of the 9 codes to be erased by
pressing pushbutton 1 the same number of times as
the memory position. I.e. one depression for memory 1,
two for memory 2, etc.
4 Wait until the LED lights green constantly.
5 Press the lock button to erase the selected position and
to exit the programming mode. The LED flashes red and
the selected memory position is erased.
6 To erase additional memory positions, repeat the steps
above, and indicate the position to be erased by a
corresponding number of depressions (step 3).
Audio signals
The code handle is delivered with the audio signal
enabled, and it can be turned off as follows:
IMPORTANT: If the product does not work, remove the batteries according to the instructions on page 3 and then
re-insert them. If the product still does not work, try fitting new batteries of an approved make. If neither of these
solutions work, take the product and associated codes to your dealer.
ONLY F OR IN DOOR USE IN AC C ORDANCE WITH IP 40
1 Enter programming mode by holding the lock
button pressed until the LED lights red constantly.
2 Enter the administrator's code within 5 seconds, the
LED lights green.
3 Press pushbutton 2 once to turn the audio signal
off/on. A low tone indicates that the signal has been
turned off and a high double-tone indicates that the
audio signal has been turned on.
4 Confirm the change and exit programming mode by
pressing the lock button, or wait until the green LED
turns off.
Automatic locking
Auto locking requires that the handle returns to the
horizontal position within 9 seconds of opening. The
code handle is delivered in manual mode.
WARNING! In automatic locking mode, the code
!
handle will repeatedly attempt to re-lock within 9
seconds from opening. If the handle is not returned to its
horizontal position within this time frame, the handle
will remain unlocked. The effect is similar to the temporary
disabling of auto-locking as described below.
Auto locking can be selected as long as the handle
returns to the horizontal position within 9 seconds of a
correct code being entered. To change the mode, follow
the instructions below:
1 Enter programming mode by holding the lock
button pressed until the LED lights red constantly.
2 Enter the administrator's code within 5 seconds, the
LED lights green.
3 Press pushbutton 3 once to change the mode to/from
automatic locking. The change is confirmed by three
short beeps (On) or a low pitch tone (Off).
4 Confirm the change and exit programming mode by
pressing the lock button, or wait until the green LED
turns off.
Temporary disabling of automatic locking
Enter a correct user code and wait until the LED stops
flashing. Immediately press pushbuttons 1 and 4 at the
same time. The door is now unlocked until the next time
the lock button is pressed or a user code is entered, after
which the handle returns to automatic locking mode.
Resetting the code memory
The code handle can be reset to factory settings
by changing the administrator's code, see steps 1-6
"Register an administrator's code" under
"Fitting instructions Code Handle".
The settings will then be:
• Empty user codes
• Audio signal on
• Auto locking off
7