Advertisement
Available languages
Available languages
Operating Instructions
®
MaxLite LED PLL DirectFit Series
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
DANGER – RISK OF SHOCK – DISCONNECT POWER BEFORE INSTALLATION
CAUTION – RISK OF FIRE. DO NOT INSTALL THIS LAMP IN A PRE-HEAT LUMINAIRE.
CAUTION – RISK OF FIRE. USE ONLY IN LUMINAIRES THAT HAVE CONSTRUCTION
FEATURES
CAUTION – RISK OF FIRE OR SHOCK. DO NOT OPEN OR MODIFY.
CAUTION - RISK OF FIRE. IF THE LAMP OR LUMINAIRE EXHIBITS UNDESIRABLE OPERATION (BUZZING,
FLICKERING, ETC.), IMMEDIATELY TURN OFF POWER, REMOVE LAMP FROM LUMINAIRE AND CONTACT
MANUFACTURER.
NOT INTENDED FOR USE WITH EMERGENCY EXIT FIXTURES/LIGHTS.
THIS LAMP ONLY OPERATES ON ELECTRONIC BALLASTS. IF LAMP DOES NOT LIGHT WHEN THE LUMINAIRE
IS ENERGIZED, REMOVE LAMP FROM LUMINAIRE AND CONTACT LAMP MANUFACTURER OR QUALIFIED
ELECTRICIAN.
THIS RETROFIT KIT CAN REPLACE 36W 40W CFL LAMPS WITH 2G11 BASES.
THIS LAMP IS NOT COMPATIBLE WITH ALL BALLASTS. BEFORE INSTALLATION, CHECK COMPATABILITY OF LED
LAMPS AND LUMINAIRE BALLAST.
SUITABLE FOR DAMP LOCATIONS. DO NOT USE WITH DIMMERS.
THIS DEVICE IS NOT INTENDED FOR USE WITH EMERGENCY EXITS.
SEE MAXLITE.COM FOR BALLAST COMPATIBILITY.
Installation Instructions
1.
Turn off the power to the luminaire. (Fig. 1)
2.
Remove diffuser (if provided).
3.
Remove the existing CFL lamps from the luminaire.
Verify the ballast is listed on the datasheet of MaxLite
PLL Directfit Series 14W. Confirm the lampholder has
a 2G11 socket.
4.
Install MaxLite LED PLL lamp into the open socket.
Ensure that the pins are firmly seated in the lampholders.
5.
Replace diffuser (if removed in step 2).
6.
Switch on power to the luminaire. (Fig. 2)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)this device may not cause harmful interference, and (2)this device must accept any interference
received, including interference that may cause undesired operation
© Copyright 2019. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 Fax: 973-244-7333 Email: info@maxlite.com
LED PLL DirectFit Series
Picture is for illustration
purposes only. Your model
may vary.
Page: 1
REV: 6/12/19
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for MaxLite LED PLL DirectFit Series
Summary of Contents for MaxLite LED PLL DirectFit Series
- Page 1 (1)this device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation © Copyright 2019. MaxLite, Inc. All Rights Reserved. Page: 1 12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 Fax: 973-244-7333 Email: info@maxlite.com REV: 6/12/19...
- Page 2 MaxLite or its authorized distributor/dealer (the “Warranty Period”), as follows: If a Product fails to operate during the Warranty Period as a result of defects in materials or workmanship, MaxLite will, at its option, repair it, replace it with the same or like Product.
- Page 3 © Copyright 2019. MaxLite, Inc. Tous droits réservés. Page: 1 12 York Ave, West Caldwell, NJ 07006 Tél: 800-555-5629 Fax: 973-244-7333 Courriel: info@maxlite.com REV: 6/12/19...
- Page 4 Informations sur la garantie MaxLite Inc. garantit ses produits pour une période minimale de CINQ (5) ans à compter de la date d’achat originale effectuée auprès de MaxLite ou d’un de ses distributeurs/revendeurs agréés (« Période de garantie »), suivant les clauses suivantes: Si un produit ne fonctionne pas pendant la période de garantie en raison de défauts de matériel...
Need help?
Do you have a question about the LED PLL DirectFit Series and is the answer not in the manual?
Questions and answers