ADTRAN NetVanta T1/FT1 + DSX-1 Quick Start Manual

®
NetVanta T1/FT1 + DSX-1 Network Interface Module (NIM) P/N 1202863L1
Quick Start Guide
WAN-T1
S
PECIFICATIONS
Operating Frame Relay, Multilink Frame Relay,
Modes PPP, Multilink PPP, HDLC
T1/FT1 Supported Standards: AT&T TR 62411, AT&T TR 54016,
Interface Bellcore TR.194, ANSI T1.403
Line Rate: 1.544 Mbps ±75 bps
Line Code: AMI or B8ZS
Framing: D4 (SF) or ESF
FT1 Line Rate: DS0 channelized (multiples of 56/64 kbps)
Input Signal: 0 to -36 dB (DS1)
Line Build-Out: 0, -7.5, -15, -22.5 dB (long), 0 to 655 ft
(short)
Connector: RJ-48C
DS0 Assignment: Programmable
DSX-1 Supported Standards: ANSI T1.102
Interface Line Rate: 1.544 Mbps
DSX Receiver Input Range: -10 dBdsx to +6 dBdsx
Capacity: 1 to 24 DS0s
Line Codes: AMI, B8ZS
DSX-1 interface to PBX
Framing: D4 (SF) or ESF
Line Length: 0 to 655 ft and -7.5 dB
Connector: RJ-48C
Clock Source Network, internal, and through
Diagnostics Test Pattern Generation and Detection: QRSS, 511, all
ones, all zeros
Network loopbacks (local and remote); responds to both
inband and FDL loop codes (T1 interface only)
Alarm generation and detection
Network and user sets of performance data (15 minutes
and 24 hours)
Compliance FCC Part 15 Class A, EN 55022 Class A
ACTA/FCC Part 68, IC CS-03
UL/CUL 60950
Physical Dimensions: 2.75-inch W x 4.25-inch D
Operating Temperature: 0°C to 50°C
Storage Temperature: -20°C to 70°C
Relative Humidity: Up to 95 percent, noncondensing
Quick Start Guide, 61200863L1-13D, July 2005
DSX-1 DBU
Technical Support 1-888-4ADTRAN (1-888-423-8726)
For more detailed documentation, visit us online at www.adtran.com.
I I
NSTALLATION NSTRUCTIONS
1. Remove the power from the unit.
2. Slide the option module into the option slot until the module is
firmly seated against the chassis.
3. Secure the pins at both edges of the module.
4. Connect the cables to the associated device(s).
5. Complete installation of the base unit.
6. Restore power to the unit.
NetVanta modules should be installed only in
NetVanta Series products.
WAN-T1 N (RJ-48C) C
ETWORK
Pin Name Description
1 R1 Receive data from the network - Ring 1
2 T1 Receive data from the network - Tip 1
3 — Unused
4 R Transmit data toward the network - Ring
5 T Transmit data toward the network - Tip
6-8 — Unused
DSX-1 (RJ-48C) C
ONNECTION
Pin Name Description
1 R Transmit data toward the DTE- Ring
2 T Transmit data toward the DTE - Tip
3 — Unused
4 R1 Receive data from the DTE - Ring 1
5 T1 Receive data from the DTE - Tip 1
6-8 — Unused
An optional Dial Backup Interface Module (DIM) is
required for dial backup applications.
For a description of the DBU pinouts, refer to the
Quick Start Guide included with your DIM shipment.
Important: For additional details on product features,
specifications, installation, and safety, refer to the
appropriate Hardware Installation Guide on the
ADTRAN OS System Documentation CD shipped
with the base unit and available online at
www.adtran.com.
P
ONNECTION INOUTS
P
INOUTS
Copyright © 2005 ADTRAN, All Rights Reserved