Cadet Com-Pak Plus Replacement Instructions

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to
persons, including the following: Read all instructions before using this heater and receptacle.
Turn the electrical power off at the electrical panel board (circuit breaker or fuse box) and lock or tag
the panel board door to prevent someone from turning on power while you are working on the heater.
Failure to do so could result in serious electrical shock, burns, or possible death.
IF YOU ARE UNCOMFORTABLE WORKING WITH ELECTRICAL APPLIANCES, UNABLE TO FOLLOW
THESE GUIDELINES, OR DO NOT HAVE THE NECESSARY EQUIPMENT, CONSULT A LICENSED ELECTRICIAN
1. It is important that you verify power has been turned off and no
power is going to the heater before proceeding. Circuit breakers
are often not marked correctly and turning the wrong breaker off
could mean electricity is flowing to the heater, even if the heater
does not appear to be working.
1. Remove knob (if applicable) and screws to remove grill.
2. Remove grill.
3. Remove heatbox from wall can by loosening screw at top.
4. Unwiring
A. Remove insulated wire connectors that connect heatbox
to wall can.
B. Cut as many nylon wire ties on back of heater as necessary
for easier accessibility.
C. Cut motor wires (back of heater) as close to motor as possible.
Strip 1/2" of insulation from remaining wires (See Figure 1.)
5. Turn heater upward, remove screw at the bottom of face cover,
just above thermostat location.
6. Lift face from bottom and slide over tab on top of box, set aside.
7. Remove blower from front by inserting screwdriver through
center portion of motor in back of heatbox and giving a quick
"pop" to the blower (Figure 1). Be careful not to bend heating
element or damage fan blower.
cadetheat.com Tel: 855.CADET.US P.O. Box 1675 Vancouver, WA 98668-1675
IMPORTANT INSTRUCTIONS
WARNING
INSTALLATION INSTRUCTIONS
SAVE THESE INSTRUCTIONS
The Com-Pak / Com-Pak Plus Motor
Replacement Instructions
http://cadetheat.com/products/wall-heaters/com-pak
MODELS
The Com-Pak Plus/Com-Pak
C202, C152, C122, C102,
C072, C151, C101, C051, C208
CS021, CS051, CS052, CS058,
CS072, CS078, CS101, CS102,
CS118, CS122, CS151, CS152,
CS158, CS202, CS208
Note: Now is the perfect opportunity to clean your
heater. See original product Owner's Guide or go to
cadetheat.com/support/install-help#install
find a detailed cleaning instruction video.
TOOLS REQUIRED
• Phillips Screwdriver
• Wire Cutter
• Wire Strippers
• Nylon Wire Ties
2. Once you verify the power has been turned off correctly,
proceed to the next step.
3. Please see your product Owner's Guide for additional
installation, operation, and maintenance instructions for both
motor and heater. Owner's Guides may be downloaded at
cadetheat.com
8. Use nut driver to remove the two nuts that secure motor to heater
shell. Motor can now be removed easily. (See Figure 3)
9. Attach new motor and tighten nuts. Do not overtighten. (See
Figure 3)
10. Properly align blower and press back into place. Spin with
finger to make sure blower is spinning freely. (See Figure 2)
11. Replace face cover over tab on top. Snap into place. Make sure
all wires are tightly pulled through pass through holes and not
caught in cover.
12. Tighten securing screw on bottom of face.
13.Wiring (Specific wiring diagrams on pages 2 and 3.)
A. Connect each new motor wire to a previously stripped heater
wire, using wire connectors.
B. Fasten the wiring with wire ties so all wires fit neatly to the
side of the motor and are out of the way. Cut off wire tie ends.
C. Reconnect supply lead wires to heater, using wire connectors.
Double check connections for tightness.
14. Reinstall heater into wall can tabs first, then attach screw.
15. Attach grill.
16.Turn power on and test heater.
The Com-Pak Twin Plus/
Com-Pak Twin
CT402, CT302, CT408,
CST102, CST152,
CST302, CST308,
CST402, CST408
and
• Crimping Tool and Connectors
• Needle Nose Pliers
• 5/16" Nut Driver
• Wire Connectors
©2016 Cadet Printed in U.S.A. 11/16 #720203