Operation And Programming - Hitachi SJ700 Series Manual

OPERATION and PROGRAMMING

SJ700 Series can be easily operated with the digital operator provided as standard. The digital operator can also be detached and
can be used for remote-control. Multilingual (English, French, German, Italian , Spanish and Portuguese) operator with copy
function (SRW-0EX) and digital operator with potentiometer are also available as options.
Parameter Display
Displays frequency, motor current,
rotational speed of the motor, and
an alarm code.
Monitor LEDs
Shows drive status.
RUN key enable LED
Lights up when the inverter
is ready to respond to the
RUN key.
RUN Key
Press to run the motor.
STOP/RESET Key
Press to stop the drive or
reset an alarm.
Function Key
Press to set or monitor a
parameter value.
Setting the output frequency
Power on
（ ）
1 or the value previously
monitored is displayed.
POWER
ALARM
Hz
RUN
V
kW
A
PRG
%
機能 記憶
FUNC STR
Press key.
FUNC FUNC
（ 2 ） Function code appears.
POWER
ALARM
Hz
RUN
V
kW
A
PRG
%
機能 記憶
FUNC STR
Press
until appears.
（ ）
3 appears.
POWER
ALARM
Hz
RUN
V
kW
A
PRG
%
機能 記憶
FUNC STR
Press key.
FUNC
（ ）
4 Preset value is displayed.
POWER
ALARM
Hz
RUN
V
kW
A
PRG
%
機能 記憶
FUNC STR
Press
to set desired value.
（ 5 ） Newly set value is displayed.
POWER
ALARM
Hz
RUN
V
kW
A
PRG
%
機能 記憶
FUNC STR
STR
Press key
to store the value.
（ ）
6 Returns to and
the setting is complete.
POWER
ALARM
Hz
RUN
V
kW
A
PRG
%
機能 記憶
FUNC STR
* To run the motor, go back to mon-
itor mode or basic setting mode.
Power LED
Lights when the power input
to the drive is ON.
ALARM LED
Lights to indicate that the
inverter has tripped.
Display Unit LEDs
Indicates the unit associated
with the parameter display.
Store Key
Press to write the new value
to the EEPROM.
Up/Down Keys
Press up or down to sequence
through parameters and func-
tions shown on the display, and
increment/decrement values.
The contents of a basic mode display.(default)
If a desired parameter is not displayed, check the
setting of function "b037"
restriction). To display all parameters, specify "00" for
"b037".
No. Display code
1 d001 to d104 Monitor display
2 F001 Output frequency setting
3 F002 Acceleration (1) time setting
4 F003 Deceleration (1) time setting
5 F004 Operation direction setting
6 A001 Frequency source setting
7 A002 Run command source setting
8 A003 Base frequency setting
9 A004 Maximum frequency setting
10 A005 [AT] selection
11 A020 Multi-speed frequency setting
12 A021 Multi-speed 1 setting
13 A022 Multi-speed 2 setting
14 A023 Multi-speed 3 setting
15 A044 1st control method
16 A045 V/f gain setting
17 A085 Operation mode selection
18 b001 Selection of restart mode
19 b002 Allowable under-voltage power failure time
20 b008 Retry-after-trip selection
21 b011 Retry wait time after trip
22 b037 Function code display restriction
23 b083 Carrier frequency setting
24 b084 Initialization mode selection
25 b130 Selection of overvoltage suppression function
26 b131 Setting of overvoltage suppression level
27 C021 Setting of intelligent output terminal 11
28 C022 Setting of intelligent output terminal 12
29 C036 Alarm relay active state
(function code display
Item
8