Hitachi SJ700 Series Manual page 13

Code Code Function Name Function Name
A105 OI-L input start frequency enable
A111 O2-L input active range start frequency
A112 O2-L input active range end frequency
A113 O2-L input active range start voltage
A114 O2-L input active range end voltage
A131 Acceleration curve constants setting
A132 Deceleration curve constants setting
A141 Operation-target frequency selection 1
A142 Operation-target frequency selection 2
A143 Operator selection
A145 Frequency to be added
A146 Sign of the frequency to be added
A150 EL-S-curve acceleration ratio 1
A151 EL-S-curve acceleration ratio 2
A152 EL-S-curve deceleration ratio 1
A153 EL-S-curve deceleration ratio 2
●
B GROUP: FINE TUNING FUNCTIONS
Code Function Name
b001 Selection of restart mode
b002 Allowable under-voltage power failure time
b003 Retry wait time before motor restart
b004 Instantaneous power failure/under-voltage trip alarm enable
b005 Number of restarts on power failure/under-voltage trip events
b006 Phase loss detection enable
b007 Restart frequency threshold
b008 Selection of retry after tripping
b009 Selection of retry after undervoltage
b010 Selection of retry count after overvoltage or overcurrent
b011 Retry wait time after tripping
b012 Electronic thermal setting (calculated within the inverter from current output)
b212 Electronic thermal setting (calculated within the inverter from current output), 2nd motor
b312 Electronic thermal setting (calculated within the inverter from current output), 3rd motor
b013 Electronic thermal characteristic
b213 Electronic thermal characteristic, 2nd motor
b313 Electronic thermal characteristic, 3rd motor
b015 Free-setting electronic thermal frequency (1)
b016 Free-setting electronic thermal current (1)
b017 Free-setting electronic thermal frequency (2)
b018 Free-setting electronic thermal current (2)
b019 Free-setting electronic thermal frequency (3)
b020 Free-setting electronic thermal current (3)
b021 Overload restriction operation mode
b022 Overload restriction setting
b023 Deceleration rate at overload restriction
b024 Overload restriction operation mode (2)
b025 Overload restriction setting (2)
b026 Deceleration rate at overload restriction (2)
b027 Overcurrent suppression enable
b028 Active frequency matching, scan start frequency
b029 Active frequency matching, scan-time constant
b030 Active frequency matching, restart frequency select
b031 Software lock mode selection
b034 RUN/ power-on warning time
b035 Rotational direction restriction
b036 Reduced voltage start selection
b037 Function code display restriction
b038 Initial-screen selection
b039 Automatic user-parameter setting function enable
Torque limit selection
b040
b041 Torque limit(1) (Forward-driving in 4-quadrant mode)
b042 Torque limit(2) (Reverse-regenerating in 4-quadrant mode)
b043 Torque limit(3) (Reverse-driving in 4-quadrant mode)
b044 Torque limit(4) (Forward-regenerating in 4-quadrant mode)
b045 Torque limit LADSTOP enable
b046 Reverse RUN protection enable
b050 Controlled deceleration and stop on power loss
b051 DC bus voltage trigger level during power loss
b052 Over-voltage threshold during power loss
b053 Deceleration time setting during power loss
b054 Initial output frequency decrease during power loss
b055 Proportional gain setting for nonstop operation at power loss
Monitored data or setting Monitored data or setting
00 (external start frequency), 1 (0 Hz)
-400. to -100., -99.9 to 0.00 to 99.99, 100.0 to 400.0 (Hz)
-400. to -100., -99.9 to 0.00 to 99.99, 100.0 to 400.0 (Hz)
-100. to 02 end-frequency rate (%)
"02 start-frequency rate" to 100. (%)
01 (smallest swelling) to 10 (largest swelling)
01 (smallest swelling) to 10 (largest swelling)
00 (digital operator), 01 (keypad potentiometer), 02 (input via O), 03 (input via OI),
04 (external communication), 05 (option 1), 06 (option 2), 07 (pulse-string frequency input)
00 (digital operator), 01 (keypad potentiometer), 02 (input via O), 03 (input via OI),
04 (external communication), 05 (option 1), 06 (option 2), 07 (pulse-string frequency input)
00 (addition: A141 + A142), 01 (subtraction: A141 - A142), 02 (multiplication: A141 x A142)
0.00 to 99.99, 100.0 to 400.0 (Hz)
00 (frequency command + A145), 01 (frequency command - A145)
0. to 50. (%)
0. to 50. (%)
0. to 50. (%)
0. to 50. (%)
Monitored data or setting
00 (tripping), 01 (starting with 0 Hz), 02 (starting with matching frequency), 03 (tripping after
deceleration and stopping with matching frequency), 04 (restarting with active matching frequency)
0.3 to 25.0 (s)
0.3 to 100.0 (s)
00 (disabling), 01 (enabling), 02 (disabling during stopping and decelerating to stop)
00 (16 times), 01 (unlimited)
00 (disabling), 01 (enabling)
0.00 to 99.99, 100.0 to 400.0 (Hz)
00 (tripping), 01 (starting with 0 Hz), 02 (starting with matching frequency), 03 (tripping after
deceleration and stopping with matching frequency), 04 (restarting with active matching frequency)
00 (16 times), 01 (unlimited)
1 to 3 (times)
0.3 to 100.0 (s)
0.20 x "rated current" to 1.00 x "rated current" (A)
0.20 x "rated current" to 1.00 x "rated current" (A)
0.20 x "rated current" to 1.00 x "rated current" (A)
00 (reduced-torque characteristic), 01 (constant-torque characteristic), 02 (free setting)
00 (reduced-torque characteristic), 01 (constant-torque characteristic), 02 (free setting)
00 (reduced-torque characteristic), 01 (constant-torque characteristic), 02 (free setting)
0. to 400. (Hz)
0.00 to rated current (A)
0. to 400. (Hz)
0.00 to rated current (A)
0. to 400. (Hz)
0.00 to rated current (A)
00 (disabling), 01 (enabling during acceleration and deceleration), 02 (enabling during constant
speed), 03 (enabling during acceleration and deceleration (increasing the speed during regeneration))
0.20 x "rated current" to 1.00 x "rated current" (A)
0.10 to 30.00 (s)
00 (disabling), 01 (enabling during acceleration and deceleration), 02 (enabling during constant speed),
03 (enabling during acceleration and deceleration (increasing the speed during regeneration))
0.20 x "rated current" to 2.00 x "rated current" (A)
0.10 to 30.00 (s)
00 (disabling), 01 (enabling)
0.20 x "rated current" to 2.00 x "rated current" (A)
0.10 to 30.00 (s)
00 (frequency at the last shutoff), 01 (maximum frequency), 02 (set frequency)
00 (disabling change of data other than "b031" when SFT is on), 01 (disabling change
of data other than "b031" and frequency settings when SFT is on), 02 (disabling change
of data other than "b031"), 03 (disabling change of data other than "b031" and
frequency settings), 10 (enabling data changes during operation)
0. to 9999. (0 to 99990), 1000 to 6553 (10000 to 655300) (hr)
00 (enabling both forward and reverse rotations), 01 (enabling only forward rotation), 02 (enabling only reverse rotation)
0 (minimum reduced voltage start time) to 255 (maximum reduced voltage start time)
00 (full display), 01 (function-specific display), 02 (user setting), 03 (data comparison display), 04 (basic display)
00 (screen displayed when the STR key was pressed last), 01 (d001), 02 (d002), 03 (d003), 04 (d007), 05 (F001)
00 (disabling), 01 (enabling)
00 (quadrant-specific setting), 01 (switching by terminal), 02 (analog input), 03 (option 1), 04 (option 2)
0. to 200. (%), no (disabling torque limitation)
0. to 200. (%), no (disabling torque limitation)
0. to 200. (%), no (disabling torque limitation)
0. to 200. (%), no (disabling torque limitation)
00 (disabling), 01 (enabling)
00 (disabling), 01 (enabling)
00 (disabling), 01 (enabling)
0.0 to 999.9, 1000. (V)
0.0 to 999.9, 1000. (V)
0.01 to 99.99, 100.0 to 999.9, 1000. to 3600. (s)
0.00 to 10.00 (Hz)
0.00 to 2.55
×
［◯
= Allowed = Not permitted
Setting Setting Change Change
Default Setting Default Setting
during operation during operation during operation during operation
-FE(CE) -FE(CE) -FU(UL) -FU(UL)
(allowed or not) (allowed or not) (allowed or not) (allowed or not)
00 00 × ○
0.00 0.00 × ○
0.00 0.00
× ○
-100. -100.
× ○
100. 100.
× ○
02 02
× ○
02 02 × ○
02 02 × ○
03 03 × ○
00 00
× ○
0.00 0.00
× ○
00 00
× ○
25. 25.
× ×
25. 25. × ×
25. 25. × ×
25. 25. × ×
×
［◯
= Allowed = Not permitted
Setting Change
Default Setting
during operation during operation
-FE(CE) -FU(UL)
(allowed or not) (allowed or not)
00 00 × ○
1.0 1.0
× ○
1.0 1.0
× ○
00 00
× ○
00 00 × ○
00 00 × ○
0.00 0.00 × ○
00 00 × ○
00 00 × ○
3 3
× ○
1.0 1.0
× ○
× ○
Rated current of
× ○
inverterx 1..0
× ○
01 01 × ○
01 01 × ○
01 01 × ○
0. 0. × ○
0.0 0.0
× ○
0. 0.
× ○
0.0 0.0
× ○
0. 0. × ○
0.0 0.0 × ○
01 01 × ○
× ○
Rated current x 1.50
1.00 1.00 × ○
01 01
× ○
× ○
Rated current x 1.50
1.00 1.00 × ○
01 01 × ○
× ○
Rated current of inverterx 1..0
0.50 0.50 × ○
00 00 × ○
01 01
× ○
0. 0.
× ○
00 00 × ×
06 06 × ○
04 04 × ○
01 01 × ○
00 00 × ○
00 00 ○
×
150. 150.
× ○
150. 150.
× ○
150. 150.
× ○
150. 150. × ○
00 00 × ○
00 00 × ○
00 00 × ×
0.0 0.0 × ×
0.0 0.0
× ×
1.00 1.00
× ×
0.00 0.00
× ×
0.20 0.20
○ ○
］
］
12