General - Carrier 40VMU012 Installation And Maintenance Instructions Manual

CAUTION
DO NOT re-use compressor oil or any oil that has been
exposed to the atmosphere. Dispose of oil per local codes
and regulations. DO NOT leave refrigerant system open to
air any longer than the actual time required to service the
equipment. Seal circuits being serviced and charge with
dry nitrogen to prevent oil contamination when timely
repairs cannot be completed. Failure to follow these proce-
dures may result in damage to equipment. For information
about replacement oil type and viscosity, see the Installa-
tion, Start-Up, and Service Instructions for the 38VMAH
and 38VMAR outdoor units.
UNIT 40VMU
POWER SUPPLY (V-Ph-Hz)
COOLING CAPACITY (Btuh)
HEATING CAPACITY (Btuh)
INDOOR FAN MOTOR
Type
Input (W)
INDOOR COIL
Number of Rows
Fin Spacing (fins/in.)
Fin Type
Tube Diameter, OD (in.)
Tube Type
Number of Circuits
INDOOR AIRFLOW (cfm)
Low
Medium
High
INDOOR NOISE LEVEL (dBA)
Low
Medium
High
UNIT
Unit Dimensions, W x H x D (in.)
Packing Dimensions, W x H x D (in.)
Net/Gross Weight (lb)
REFRIGERANT TYPE
EXPANSION DEVICE
DESIGN PRESSURE, High/Low (psig)
REFRIGERANT PIPING (in.)
Liquid Side, OD
Suction Side, OD
CONNECTING WIRING (AWG)
Power Wiring
Signal Wiring
DRAINAGE WATER PIPE DIAMETER, OD (in.)
LEGEND
AWG — American Wire Gage
EEV — Electronic Expansion Valve
NEC — National Electrical Code
The 40VMU under ceiling/floor unit can be installed ex-
posed at the ceiling or mounted on the wall close to the floor. It
is ideal for corner or low-ceiling areas where soffit space is not
available for furred-in units.
The equipment is initially protected under the manufactur-
er's standard warranty; however, the warranty is provided un-
der the condition that the steps outlined in this manual for ini-
tial inspection, proper installation, regular periodic mainte-
nance, and everyday operation of the unit be followed in detail.
This manual should be fully reviewed in advance before initial
installation, start-up and any maintenance. Contact your local
sales representative or the factory with any questions BEFORE
proceeding.
Table 1 lists physical data for each unit size. See Fig. 1 for
the model number nomenclature. Figures 2 and 3 show the unit
dimensions. Table 2 shows components that may or may not be
used for a particular installation.
Table 1 — 40VMU Physical Data
012 015
12,000 15,000 18,000
13,500 17,000 21,000
24
47
2
15
Aluminum with Hydrophilic Coating
3
259 359
294 412
335 441
35.8 41.7
37.7 45.4
40.5 47.2
39 x 26 x 8
1
43 x 29 / x 12
2
57/71
1 /
4
1 /
2
Sized per NEC and Local Codes Based on Nameplate Electrical Data
2-Core Stranded Shielded Twisted Pair Cable 20 AWG-16 AWG
2

GENERAL

018 024 030
208/230-1-60
24,000 30,000
27,000 34,000
DC Motor
53 80 107
3
14
3
/
8
Copper Tube with Inner Groove
5
394 494 624
424 529 676
471 571 729
44.1 50.2 50.4
46.5 52.0 52.1
48.5 53.8 53.9
1
50 / x 26
2
x 8
55 x 29
x 12
62/75 77/90
R-410A
EEV (Built-In)
580/320
3 /
8
5
/
8
5 /
8
036 048
36,000 48,000
40,000 54,000
67*2 115*2
7
906 929
976 1000
1094 1353
48.4 50.6
50.3 52.3
53.0 59.8
66 x 27 x 10
1
/
2
75 1 / x 30 x 13
2
106/128