Advertisement
Quick Links
Advertisement
Related Manuals for Garlando Toorx BRX100 ERGO
Summary of Contents for Garlando Toorx BRX100 ERGO
- Page 1 INSTRUCTION iConsole App Manual www.toorx.it/iconsole...
- Page 2 EXPLODED DRAWING...
- Page 3 PART LIST Part # Description Quantity Upper computer cable Screw Computer plastic cover (Left) Computer plastic cover (Right) Screw Self-tapping screw Saddle Tube spacer Round-shaped Knob Seat post plastic cover (Left) Seat post plastic cover (Right) Screw Seat post Tube bundle Round head grooved pin Lower computer cable Sensor set...
- Page 4 Part # Description Quantity Crank (Right) Anti-loose hex head bolt Crank end cap Pedal (Left) Pedal (Right) Screw Joint lever Hex screw Spring washer Washer Rear end cap Rear Stabilizer Flat washer Allen bolt DC line Spring washer Washer Belt wheel Pedal Axle Allen head screw Upper protective cover...
- Page 5 Part # Description Quantity Idler Waved washer Spring Allen key wrench Combination wrench Computer SE1010 EMS flywheel Belt 400J6 Flat washer 1T×Φ6.5×Φ13mm Flat washer 1T×Φ8.5×Φ20mm Screw M6×12mm Screw M5×20mm Control board Main frame Idler wheel pole Computer cable Adaptor...
- Page 6 ASSEMBLY INSTRUCTION STEP 1 Attach the Front Stabilizer (59) onto the Main Frame (19) with Flat washer (48), Spring washer (51) and M8 Allen bolt (49).Tighten fully. Attach the Rear Stabilizer (47) onto the Main Frame (19) with Flat washer (48), Spring washer (51) and M8 Allen bolt (49).Tighten fully.
- Page 7 STEP 2 Pull out the Upper protective cover (57) from the Main frame (19) and attach it to the Handlebar post (63) shown as right image Connect the Upper Computer Cable (2) with Lower Computer Cable (16) shown as the left top image. Attach the Handlebar Post (63) onto the Main Frame (19) with M8 Allen Bolts (61), Spring Washers (51), Flat washer (48) or Curved Washers (62).
- Page 8 STEP 3 Assemble the saddle (7) to the adjustable Seat post (12) by the nut shown as the left image. Place the Seat Post (12) into the Main Frame (19), set it at the desired position and lock it by inserting Round head grooved pin (14) in place and tighten fully.
- Page 9 STEP 4 Assemble the pedals Left and Right (33L) & (33R) to the crank Left and Right (30L) & (30R). Attach the Handlebar (69) onto the Handlebar Post (63) with Tube Spacer (8) and Round-shaped Knob (9).Tighten fully. Remember to pull the Hand pulse cable (67) through the hole above Handlebar holder plate (63) and extent to the upright position, see the right image.
- Page 10 STEP 5 Remove the screws (3) from the back of the computer (89). Connect the Upper Computer Cable (2) with the Computer (89). Connect the Hand pulse cables (67) with the Computer (89). Attach the Computer (89) onto the computer bracket with 4 M5 screws (3).
- Page 11 STEP 6 Attach the left and right Computer Plastic Cover (4L+4R) onto the Handlebar with and M4 Screws (6) and M5 Screws (5). Now your machine is ready for use.
- Page 12 COMPUTER INSTRUCTION MANUAL DISPLAY FUNCTIONS ITEM DESCRIPTION+ TIME Count up - No preset target, Time will count up from 00:00 to maximum 99:59 with each increment is 1 minute. Count down - If training with preset Time, Time will count down from preset to 00:00. Each preset increment or decrement is 1 minute between 00:00 to 99:00.
- Page 13 OPERATION: POWER ON Plug in power supply, computer will power on and display all segments on LCD for 2 seconds (Drawing 1). Drawing 1 WORKOUT SELECTION Use UP or DOWN (Encoder) to select workout Manual (Drawing 2)à Beginner(Drawing 3) à Advance (Drawing 4) à Sporty(Drawing 5) à...
- Page 14 Drawing 10 Drawing 11 Drawing 12 Beginner Mode 1. Use UP or DOWN (Encoder) to select workout program, choose Beginner mode and press MODE / ENTER to get into. 2. Use UP or DOWN (Encoder) to select Beginner program 1~4 (Drawing 13) and press MODE / ENTER to get...
- Page 15 Drawing 15 Cardio Mode Use UP or DOWN (Encoder) to select workout program, choose H.R.C. and press MODE / ENTER to get into. Use UP or DOWN (Encoder) to set Age (Drawing 16). Use UP or DOWN (Encoder) to select 55% (Drawing 17).75%.90% or TAG (TARGET H.R.) (default: 100). Use UP or DOWN (Encoder) to set workout TIME.
- Page 16 During measuring, users have to hold both hands on the hand grips. And the LCD will display “= ” “= = ” (Drawing 22)for 8 seconds until computer finish measuring. LCD will display BODY FAT advice symbol, BODY FAT percentage (Drawing 23), BMI (Drawing 24)
- Page 17 2. Once console is connect to smart device via Bluetooth , the console will don’t display. Noted: 1. After 4 minutes without pedaling or pulse input, console will enter into power saving mode. Press any key may wake the console up. 2.
- Page 18 GARLANDO SPA Via Regione Piemonte, 32 - Zona Industriale D1 15068 - Pozzolo Formigaro (AL) - Italy www.toorx.it - info@toorx.it...