Download
Share
Print this page
Garlando Everfit MSK 500 Instructions Manual
  1. Manuals
  2. Brands
  3. Garlando Manuals
  4. Fitness Equipment
  5. Everfit MSK 500
  6. Instructions manual

Garlando Everfit MSK 500 Instructions Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
INSTRUCTION
Ed :
08/18
Rev:
00
Cod :
GRLDEVEFTK500

Advertisement

loading

Related Manuals for Garlando Everfit MSK 500

Summary of Contents for Garlando Everfit MSK 500

  • Page 1 INSTRUCTION Ed : 08/18 Rev: Cod : GRLDEVEFTK500...

  • Page 2: Safety Information

    Safety Information Free area shall be not less than 0.6m greater than the training area in the directions from which • the equipment is accessed. The free area must also include the area for emergency dismount. Where equipment is positioned adjacent to each other the value of the free area may be shared. Keep unsupervised children away from the equipment.

  • Page 3: Components - Parts

    MUST read all instructions before using any fitness equipment. Argos assumes no responsibility for Components - Parts personal injury or property damage sustained by or through the use of this product. Please check you have all parts listed below Note: Some of the smaller components may be pre-fitted to larger components.
  • Page 4 Components - Parts Please check you have all parts listed below Note: Some of the smaller components may be pre-fitted to larger components. Please check carefully before contacting us regarding any missing components. Foam roll tube × 2 Rear U-shaped 120mm Bracket ×...
  • Page 5 Components - Parts Please check you have all parts listed below Note: Some of the smaller components may be pre-fitted to larger components. Please check carefully before contacting us regarding any missing components. 54. 25 × 50mm 45mm End cap × 5 38mm End cap ×...
  • Page 6 Components - Parts Please check you have all parts listed below Note: Some of the smaller components may be pre-fitted to larger components. Please check carefully before contacting us regarding any missing components. 71. Ø 78mm Pulley 8LBS Select 10LBS Weight ×...

  • Page 7: Components - Fixings

    Components - Fixings Please check you have all fixings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more hardware may be supplied than is actually required. Some of the smaller components may be pre-fitted to the larger components.
  • Page 8 Assembly instructions Step 1 a. Insert the Guide rods (18) into the holes on the Rear stabilizer (4). Fix using 2 x M10 x 25mm Allen bolts (34) and 2 x Ø10mm Washers (41). b. Slide 2 x Ø61mm Rubber bumpers (58) down onto Guide rods (18).
  • Page 9 Assembly instructions Step 2 Attach the Base frame (1) to the Rear stabilizer (4). Fix using 2 x M10x 65mm Carriage bolts (27), the Rear U-shaped bracket (19), 2 x Ø10mm Washers (41) and 2 x M10 Aircraft nuts (42).
  • Page 10 Assembly instructions Step 3 a. Attach the Front stabilizer (16) to the Leg developer holder (5), fix using 2 x M10 x 16mm Allen bolts (75), 2 x Ø10mm Washers (41). b. Attach the Leg developer holder (5) to the Base frame (1) fix using 120mm Bracket (20), 2 x M10 x 65mm Carriage bolts (27), 2 x...
  • Page 11 Assembly instructions Step 4 a. Carefully slide 9x 10LBS Weight plates (73) down Guide rods (18), insert the Select rod (13) into the Weight plates (73), and then slide 1 x 8LBS Select plate (72) down Guide rods (18) b. Select the desired training weight by inserting the Stack select pin (44) into the deep grooves under the Weight plates and into the Select rod.
  • Page 12 Assembly instructions Step 5 Attach the Vertical frame (3) to the Base frame (1). Fix using 2 x M10 x 65mm Carriage bolts (27), 120mm Bracket (20), 2 x Ø10mm Washers (41) and 2 x M10 Aircraft nuts (42). Note: (37/57) was fixed in the factory.
  • Page 13 Assembly instructions Step 6 a. Attach Upper frame (2) to Guide rods (18) fix using 2 x M10 x 25mm Allen bolts (34) and 2 x Ø10mm Washers (41). b. Attach Upper frame (2) to the Vertical frame (3) fix using 2 x M10 x 65mm Carriage bolts (27), 120mm Bracket (20), 2 x Ø10mm Washers (41) and 2 x M10 Aircraft nuts (42), Note: (52/48) was fixed in the factory.
  • Page 14 Assembly instructions Step 7 Attach the Front press base (6) to the Upper frame (2) using the M10 x 103mm Axle (21). Secure using 2 x Ø25 x Ø11x1.5 Washers (39) and 2 x M10 Aircraft nuts (42). Note: (38/43/52) were fixed in the factory.
  • Page 15 Assembly instructions Pivot Pre-fitted Step 8 a. Attach the ‘pivots’ on the Right and Left Butterfly’s (7 & 8) to the Front press base (6) using 2 x Ø25 x Ø11 x 1.5 Washers (39) and 2 x M10 Aircraft nuts (42). b.
  • Page 16 Assembly instructions Step 9 Step 8 a. Attach the Backrest pad (24) to the Vertical frame (3) using 2 x M8 x 60mm Allen bolts (35) and 2 x Ø8mm Washers (40). b. Attach the Seat pad (25) to the Base frame (1) using 2 x M8 x 40mm Allen bolts (61) and 2 x Ø8mm Washers (40).
  • Page 17 Assembly instructions Pre-fitted Pre-fitted Step 10 a. Slide the Foam roll tube (17) into the hole on the Base frame (1). Push 2 x Ø17mm Foam rolls (69) onto each side of the Foam roll tube (17). b. Attach the Leg developer (15) to the Base frame (1) using M10 x 60mm Allen bolts (29) and 2 x Ø10mm Washers (41), M10 Aircraft nut (42) and M10 Nut cap (64).
  • Page 18 Assembly instructions Step 11 a. Attach the Preacher pad (26) to the Preacher pad stand (9). Secure using 2 x M8 x 18mm Allen bolts (36) and 2 x Ø8mm Washers (40). b. Insert the Preacher pad assembly into the Base frame (1). Select the desired height and secure using the Lock knob (68).
  • Page 19 Assembly instructions Step 12 Important: Study and follow the diagram carefully. a. Feed the bolt end of the 2700mm Upper cable (49) up through opening in Upper frame (2). Insert Ø22 x 15mm Pulley bushings (63) into holes and attach 1st Pulley (71) using M10 x 60mm Allen bolt (29) and M10 Aircraft nut (42).
  • Page 20 Assembly instructions Step 13 a. Hook one end of the 2750mm Butterfly cable (50) to Right butterfly (7). Place a Ø77mm Pulley (71) under the cable, position the pulley into the Swivel pulley brackets (12). Fix using M10 x 40mm Allen bolts (32), 2 x Ø10mm Washers (41) and M10 Aircraft nut (42). b.
  • Page 21 Assembly instructions...
  • Page 22 Assembly instructions Step 14 Important: Study and follow the diagram carefully. a. Feed the loop end of 2750mm Lower cable (51) through opening in the Leg developer (15). Insert 2 x Ø22 x 11mm Pulley bushings (62) into holes and attach 1st Pulley using M10 x 53mm Allen bolt (30) and M10 Aircraft nut (42).
  • Page 23 Assembly instructions Step 15 Important: Now fully tighten the fixings ensuring that all of the pulleys and brackets can move freely. Attach the Lat bar (14) onto the Upper frame (2) hooks. Connect the Pull bar (23) to the end of Lower cable (51) using 2 x Clip hooks (45) and 15 Joint chain (47).

  • Page 24: Exploded Parts List

    Exploded Parts List Part Description Qty. Part Description Qty. Base frame L-Shaped separation blade Upper frame Pull bar Vertical frame Backrest pad Rear stabilizer Seat pad Leg developer holder Preacher pad Front press base M10 x 65mm Carriage bolt Right butterfly M10 x 65mm Allen bolt Left butterfly M10 x 60mm Allen bolt...
  • Page 25 Exploded Parts List Seated press lock pin Ø22mm x 11mm Pulley bushing Stack select pin Ø22mm x 15mm Pulley bushing 6# Clip hook M10 Nut cap Pulley cover Ø26mm x 38mm Hollow sleeve 15 Joint chain Front press handle grip Ø25×130 Ø25mm ×31mm Bushing Lat pull handle grip 2700mm Upper cable...
  • Page 26 GARLANDO SPA Via Regione Piemonte, 32 - Zona Industriale D1 15068 - Pozzolo Formigaro (AL) - Italy www.everfit.it - info@everfit.it...