Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Silca TARGA 2000
Summary of Contents for Silca TARGA 2000
- Page 1 Operating manual D412790XA vers. ®...
- Page 2 This manual has been drawn up by SILCA S.p.A. All rights reserved. No part of this publication may be reproduced or used in any form or by any means (photocopying, microfilm or other) without the written permission of SILCA S.p.A. Edition: December 1999 Printed in Vittorio Veneto by SILCA S.p.A.
-
Page 3: Table Of Contents
INDEX GUIDE TO THE MANUAL ................5 GENERAL ......................6 TRANSPORT ....................7 Packing ....................7 Transport ....................7 Unpacking .....................7 Machine handling ..................7 WORKING PARTS ..................8 MACHINE DESCRIPTION ................10 Technical data ..................11 Electrical circuit ...................12 ACCESSORIES PROVIDED .................13 MACHINE INSTALLATION AND PREPARATION ........14 Separate parts ..................14 Connection to the mains ..............14 Checking for damage ................14... -
Page 5: Guide To The Manual
Operating manual - English GUIDE TO THE MANUAL This manual has been produced to serve as a guide for users of the TARGA 2000 key-cutting machine. It is essential to read it carefully and consult it regularly if you wish to operate your machine safely and efficiently. -
Page 6: General
The TARGA 2000 must be installed and used in the way laid down by the manufacturer. If the machine is used differently or for purposes different from those described in this manual, the customer will forego any rights he may have over SILCA S.p.A. -
Page 7: Transport
The packed machine can be carried by one person. Packing The TARGA 2000 key-cutting machine is consigned in a strong cardboard box, the dimensions of which are shown in fig. 3, designed to protect the machine even when it is stored for long periods. -
Page 8: Working Parts
Operating manual - English TARGA 2000 WORKING PARTS Fig. 4 Copyright Silca 1999... - Page 9 TARGA 2000 Operating manual - English TARGA 2000 key-cutting machine: A - carriage lever B - carriage handle C - chippings tray C1- tool tray D - clamp carriage D1- carriage release knobs D2- carriage horizontal locking knob E - double bit keys clamps...
-
Page 10: Machine Description
Operating manual - English TARGA 2000 MACHINE DESCRIPTION TARGA 2000 is a professional machine for the cutting of male and female bit and double bit keys. The main parts of the machine are described below: • SAFETY DEVICE Device connected to a power point with a differential switch; power the key-cutting machine by pressing the switch (X1). -
Page 11: Technical Data
TARGA 2000 Operating manual - English Technical data POWER: • 230V - 50Hz 220W 1,6A • 110V - 60Hz 250W 3,5A CUTTING TOOL: High speed steel (HSS) MOTOR:one speed single phase 230V-50Hz-1,5A / 110V-60Hz-3,5A • 230V: 1350 rpm - 0,18 Kw •... -
Page 12: Electrical Circuit
Operating manual - English TARGA 2000 Electrical circuit The TARGA 2000 key-cutting machine is provided with a motor which performs at: • 1350 rpm with consumption of approx. 0,18 kw and absorption of 1,5A for the 230V version; • 1620 rpm with consumption of approx. 0,18 kw and absorption of 3,5A for the 110V version. -
Page 13: Accessories Provided
It is advisable to ensure that the tool box always has a set of tools, a spare cutting tool, tracer point and belt and components normally subject to wear and tear. TARGA 2000 comes with a full set of all the accessories needed for its operation and maintenance. Fig. 7... -
Page 14: Machine Installation And Preparation
TARGA 2000 key-cutting machine can be installed by the purchaser and does not require any special skills. However, some checks and preparation for use are advisable. Separate parts The detachable parts of the machine are packed separately and must be fitted to the TARGA 2000 by the operator, as follows: Clamp carriage Place the clamp carriage into its seating and tighten the carriage release knobs (D1) (fig. -
Page 15: Environmental Conditions
TARGA 2000 Operating manual - English Environmental conditions To ensure that the best use is made of the TARGA 2000 key-cutting machine, certain parameters must be borne in mind: damp, badly ventilated sites should be avoided. the ideal conditions for the machine are: - temperature: between 0 and 40°C... -
Page 16: Regulation And Use Of The Machine
TARGA 2000 REGULATION AND USE OF THE MACHINE The cutting tool on the TARGA 2000 is used to cut the key blanks and must be periodically checked and replaced. Periodically check the key-cutting machine settings, to ensure perfect machine efficiency. -
Page 17: Cutting Operations
TARGA 2000 Operating manual - English Cutting operations ATTENTION: to work in complete safety, pay special attention to the following recommendations: Always work with dry hands. Check that the machine is properly earthed. Use the protective goggles, even if the cutting tool is fitted with a protective shield. -
Page 18: Cutting Female Bit And Double Bit Keys
Operating manual - English TARGA 2000 Fig. 16 Cutting female bit and double bit keys 1) Align the mobile clamp (cutting tool side) by means of the carriage locking knob (fig. 18). 2) Fit the special centring devices (G1) into their seat, pushing all the way in. - Page 19 TARGA 2000 Operating manual - English Fig. 18 Copyright Silca 1999...
-
Page 20: Maintenance
ATTENTION: for repairs or replacement of parts for maintenance, the ‘CE’ mark is guaranteed only if original spare parts provided by the manufacturer are used. Although the TARGA 2000 key-cutting machine does not require special maintenance, it is advisable to check and, if necessary, replace the parts subject to wear (cutting tool, tracer point, belt). -
Page 21: Tracer Point Replacement
TARGA 2000 Operating manual - English Replacing the belt: ATTENTION: Unplug the machine from the mains. 1) Remove the protective cover on the motor (M1) by removing the four screws. 2) Loosen the four screws which fix the motor to the base. -
Page 22: Fuse Replacement
Operating manual - English TARGA 2000 Fuse replacement ATTENTION: Unplug the machine from the mains. 1) Detach the wiring from the machine plug. 2) Turn the key-cutting machine to the right so that the fuse box is easily reached. 3) Remove the fuse box placed below the power inlet (Q) (fig. 22). -
Page 23: Waste Disposal
Re-cycling is a recommended ecological practice. Packing The TARGA 2000 is consigned in a cardboard packing box which can be re-used if undamaged. When it is to be thrown away it is classified as solid urban waste and should be placed in the special paper collecting bins. -
Page 24: Assistance
TARGA 2000 ASSISTANCE Silca provides full assistance to purchasers of the TARGA 2000 key-cutting machine. To ensure complete safety for the operator, any job not specified in this manual should be carried out by the manufacturer or in the special Service Centres recommended by Silca. - Page 25 Vittorio Veneto VITTORIO VENETO 11/11/2005 CE DECLARATION OF MACHINE COMPLIANCE SILCA S.p.A. - VIA PODGORA 20 ( Z.I.) 31029 VITTORIO VENETO (TV) - (ITALY) TEL. 0438 9136 - FAX. 0438 913800 Declares under its own responsibility that the Key-cutting machine model...
Need help?
Do you have a question about the TARGA 2000 and is the answer not in the manual?
Questions and answers