Operation; Adjusting The Volume Level - Makita DMR300 Instruction Manual

OPERATION

Switching on/off the radio
Press the Power button
Press the Power button
radio.

Adjusting the volume level

Turn the Tuning control knob
the volume. Turn the Tuning control knob
clockwise to decrease the volume.
NOTE: The volume adjustment is not available during
tuning and some settings.
Scan tuning AM/FM or DAB
1. Press the Power button
radio.
2. Press the Source button
DAB radio mode.
3. Press and hold the Tuning control knob
out an auto-tune.
Your radio will scan up the AM/FM or DAB band from
the currently displayed frequency and will stop scan-
ning automatically when it finds a station of sufficient
strength.
NOTE: The stations to be found by scan tuning vary
depending on the receiving sensitivity at the location
where the scan tuning is performed. If you don't have
desired station, change the location and perform the
procedure above.
NOTE: When the end of the waveband is reached
your radio will recommence tuning from the opposite
end of the waveband.
Manual tuning – FM/AM or DAB
1. Press the Power button
2.
Press the Source button
DAB radio mode.
3.
Press the Tuning control knob
4. Rotate the Tuning control knob
5. Press the Tuning control knob
tuning.
NOTE: Manual tuning is available while "MANUAL
TUNING" is displayed on the display. If "MANUAL
TUNING" is not displayed, start the manual tuning
from the beginning.
NOTE: The stations to be found by manual tuning
vary depending on the receiving sensitivity at the
location where the manual tuning is performed. If you
don't have desired station, change the location and
perform the procedure above.
NOTE: When the end of the waveband is reached
your radio will recommence tuning from the opposite
end of the waveband.
to switch on the radio.
again to switch off the
clockwise to increase
counter-
to switch on your
to select AM/FM or
to carry
to switch on your radio.
to select FM/AM or
.
to tune to a station.
to set the
Presetting stations in FM/AM or DAB
There are 5 preset stations each for FM/AM or DAB radio.
They are used in the same way for each waveband.
1. Press the Power button
2. Press the Source button
waveband. Tune to the required radio station.
3.
Press and hold the required Preset button (1 to
5) until the display shows "PRESET X STORED"
(X indicates the number of the Preset button that you pressed).
The station will be stored using the preset number (P1-P5).
Repeat this procedure for the remaining presets as you wish.
NOTE: Preset stations which have already been stored
may be overwritten by following the above procedure.
Recalling a preset station in AM/FM or DAB
1.
Press the Power button
2.
Press the Source button
DAB radio mode.
3. Press the desired Preset button
you stored in the preset memory.
Display modes – FM
Your radio has a range of display options for FM radio mode.
Station name
Program type
Radio text
Time/Date
Display modes – DAB
Your radio has a range of display options for DAB radio
mode.
Station name
Program type
Multiplex name
Time/Date
Frequency and channel
Bit rate/ Audio type
Signal strength
12 ENGLISH
to switch on your radio.
to select the desired
to switch on your radio.
to select AM, FM or
that
Displays the name of the sta-
tion being listened to, together
with the band and frequency.
Displays the type of station
being listened to such as Pop,
Classic, News, etc, together
with the band and frequency.
Displays radio text message
such as new items etc, together
with the band and frequency.
Displays the time and date accord-
ing to the date setting of your radio.
Displays the name of the
station being listened to.
Displays the type of station
being listened to such as Pop,
Classic, News, etc.
Displays the name of the DAB
multiplex to which the current
station belongs.
Displays the time and date.
Displays the frequency and
channel number for the cur-
rently tuned DAB station.
Displays the digital audio bit
rate and audio type for the
currently tuned DAB station.
Displays the signal strength
for the currently tuned DAB
station.