Larson Electronics IDCMR-SL-IP-POE-4MP Instruction Manual page 3

r
l
C.
�F\
\ I
�
�
\_\
Slidethe sealing plugdownpasttheRJ-45connenor.Seec.
d. Removetheinsertion tool fromtheLANcable.Seed.
e. Reinstall the sealingplug with theLAN cable intothejunction box
4. Similar tothe procedure inthe previousstep,use the insertiontool toinstall the otherpower,
audio and alarm cables through the sealing plugsin thejunctionbox.See below
Side inlet cover
Reattac!1thejunclionboxtothead apterplate.lfyouareusingcondui t wi 1 hthecondui t adapter
to routethe interface cables,remove theside inlet coverfrom thejunctionbox,andtheslidethe
conduit adapterintothesideinletbefore reattachingthejunctionbox.
Install the camera
Hook1hesafety cableon thejunction boxontothetanginthe cameramoduleandallow1he
camera to hang freely.
-
�-
=----=-
::;.�
�
Junction box �
�
Safety cable
Interface cable
Safety cable tang on
connectors
camera module
2. Attach 1heinterfilce cables tothe connectorsonthe cameramodule.See photobelowfor
connector identification.
3. Amchthe interfacecables tothe connectorson the camera module.Seeabove
Rea1tach the camera module to thejunction box usingt hefour screwsremoved earlier.\
S. Apply power to the camera through the 12 Vdc power cable or PoE injector, as configured
Step 3. Install the Alibi Config Tool software
NOTE: If the camera LAN extension cable is attached to a Network Video Recorder (NVR), skip this step
TheAlibi ConfigTool is a PC-based network utilityfor discovery of Alibi compatible devices.lt
aneasywayto activate devices,configure cameraand recorder networkconfigurationsettings,andse�
device passwords. It car1 be installed on a Microsoft ,. Windows• operating system that has direct access
to the network where your Alibi devices are installed. You can download the Alibi Configuration Tool
from Supercircuits.com or AlibiSecurity.com/Resources.
Download the Alibi Config Tool from the Supercircuits.com or AlibiSecurity.com/Resources
website. At the time when this document was published, the file is named: alibi- c onfig-tool.
zi p and isabout 80MB.
Un-zip the file on a computer with Microsoft Windows (Wiridows 7 orne_y,ier) that is connected
totheLAN where yourAlibi camera is connected.
Run the file contained ln the zip file: Alibi Con fig Tool.exe. Follow the on-screen
to install the file.
4. Open theAlibi(onfigTool application.When the application opens,it automatically"discovers"
and lists allAlibi compatible devices ontheLAN.See below.
.,,,:,_,o lfJ'"' t.,;; ><
[ii&¥¥ i#Wii4#1W8¥Fit 44
Notice:ln thescreen above,thetool discovered devices withlP addressesofl0.1.10.xxxand
192.1 6 8.3.xxx. It will also list other Alibi compatible devices on the LAN, and devices with the
address 192.168.l.64(an inactiveAlibi device)
Step 4. Activate Inactive Alibi device
NOTE: If the camera LAN extension cable is attached to a Network Video Recorder (NVR), skip this step.
Refer to the documentation available for your NVR firmware for the procedure to activate the camera, if
necessary.
When an Alibi device is first installed, or reset to its factory configuration, it must be �Activated
it can be used.ln theAlibiConfigurationTool, #lnactive"devices have aSecuritystatus oflnactive,
and an 1Pv4 address of 192.168.1.64. A device is "Activated" when a password is assigned
admin username of the device.
In the example below, an All-NS4116R camera is activated and configured for its network. The
procedureis similar forall otherAlibi networkcamerascurrentlyavailable.
Scanthrough1helistof devices theAlibiConfigTool discoveredfor thelnactive deviceyou want
toactivate(seebelow).Clickon thedevice inthelistto highlightit,andthenclicktheselectbox
to checkit.Seebelow
2. Click the Activate button. In the Ac.tiva\e window , you
provides (administrator)username.
a. In the Activa!e window, enter an a password for ad min in the New Password field.
lncludea combination of uppercase,lowercasealphabetic characters
create a " Strong" password.The ratingis shown beneaththefield.Seeabove.
instructions
Enter the admin password again in the Confirm field, and then click Activate. In the
screen below, notice that the device Security status shows "Active". Record your admin
password for reference later.
CAUTION
Noticethatalthough thedeviceisnow activated,it retained the default lPaddress.
Step 5. Modify Network Parameters
NOTE: If the camera LAN extension cable is attached to a Network Video Recorder (NVR), skip this
step. The camera will receive network configuration settings from the NVR. Refer to the documentation
available for your NVR firmware for more information
Youcan changethe networkparamerersof devices thatareactive
lnthelis1of devices discovered,clickonthe deviceyouwantto changethe networksettingsfor,
andthenclicktheselectboxto checkit.Seebelow
a
before
to the
In the popup window edit 1he current network parameters, and then enter theadmin user
,"
password inthe fielda11hebo11om.
Enable DHCP: You
� ............
from a DHCP server installed on the LAN. However, these seuings GIil be changed by the
··MEMS
DHCPserver.Since itis recommendedtousean urichanging lPaddress,you can useDHCP
to acquire compatible network settings, and then uncheck Enable OHCP and save that
configuration toretainthenew networkparameters.
lnthe example below,the1Pv4addresswas changedto 192.168.3.100,andthe1Pv4
Gateway was changed to 192. 168.3.1. These settings were determined to be compatible
withthe networkrouter andotherdevicesthatsharethe samerouter.
will create a password for the ad min
Click OK to save yourse1tings. The parameter change(s) will be shown device's network
parameters(seebelow)
and numbers to
Step 6. Login to the camera
NOTE: If the camera LAN extension cable is attached to a Network Video Recorder (NVR), skip this step
Microsoft" IE is used to access your camera remotely. IE must run as an Administrator to use all feawres
availablethrough a remoteloginto the camera.
Settiilg MS Internet Explorer
Window 7: To run IE as an Administrator:
Findorcreate an!Eicononyour computerdesktop.
Holddownthe shift key,and thenright-clickon the lEicori.
Modify Network Parameters
Cilek Run as administrator in the pop-up menu.
Window 10: To run IE as an Administrator:
Find MS IE in the start menu. Usually this is found in 1he Windows Accessories group
2. Pinthe entrytoStart
Right click on the Internet Explorer tile, and then select More I Run as administrator.
3.
can select Enable DHCP to acquire compatible network settings
run as an Administrator
to