Advertisement
Quick Links
Check to ensure that all parts are included:
Index
No. Description
1
Ice Chute
2
Wire Harness
3
Top Panel Hook
4
Thumbscrew
5
Gasket
(125×1080 mm (5"×42 1/2"))
• Only qualified service technicians should install this kit to reduce the risk of death, electric shock, serious injury,
or fire.
• Icemaker is heavy. Use care when lifting or positioning. Work in pairs when needed to prevent injury or damage.
• No installation or service should be undertaken until the technician has thoroughly read these instructions. Failure
to follow these instructions will adversely affect safety, performance, component life, and warranty coverage.
• Before Servicing: Move the control switch to the "OFF" position and turn off the power supply. Place the
disconnect in the "OFF" position. Lockout/Tagout to prevent the power supply from being turned back on
inadvertently. Control switch in "OFF" position does not de-energize all loads.
• CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after the
icemaker is serviced. Make sure that none have fallen into the dispenser unit/ice storage bin.
• Make sure all food zones in the icemaker and dispenser unit/ice storage bin are clean after service.
• Protect the floor when moving the icemaker to prevent damage to the floor.
• Wear proper PPE (personal protection equipment) when executing these procedures.
• To reduce the risk of electric shock, do not touch the control switch with damp hands.
• The manufacturer cannot be held responsible for injury or damage resulting from improper, incorrect, and
unreasonable use or installation.
• Do not use the frame to lift the icemaker. Lift the icemaker at the base or use a duct jack to lift the upper icemaker
on top of the lower icemaker
• Up to three icemakers total (including the bottom icemaker) can be stacked.
Double Stacked: IM-500SAB × 2, Stacking Kit HS-5530 × 1
Triple Stacked: IM-500SAB × 3, Stacking Kit HS-5530 × 2
• The bin control switch on the lowest icemaker controls all icemakers. The bin control switch and switch mount
must be removed from the upper icemakers. Misconnection or no connection may cause damage to the
icemakers, resulting in icemaker failure or damage.
• Allow 6" (15 cm) clearance at rear, left side, and top (upper icemaker), and 12" (30 cm) clearance at right side for
proper air circulation and ease of maintenance and/or service should they be required.
New Lower Icemaker Installation Instructions
1) Follow the Instruction Manual's installation instructions through "II.D. Setup."
When complete, continue to step 2.
Note: If installing an upper icemaker on an existing lower icemaker,
skip to step 2.
Hoshizaki IM-500SAB Stacking Kit Instructions
For Use with Hoshizaki Model IM-500SAB
Part
Number
1A5929-01
3B0590-01
3B0586-01
415949G01
4A0808L02
HS-5530
Index
Qty
No. Description
1
6
Water Guide
1
7
Wire Saddle
1
8
Wiring Label
2
9
Hex Bolt w/Washer (8×16)
1
10
Hex Nut (M8)
WARNING
NOTICE
1
Part Number Qty
4A6891-01
1
4A2338-01
2
2A9601-01
1
7B0230816
2
7N12-0800
2
Lower Icemaker
Ice Storage Bin
2A9584-010
Advertisement
Related Manuals for Hoshizaki HS-5530
Summary of Contents for Hoshizaki HS-5530
- Page 1 • Up to three icemakers total (including the bottom icemaker) can be stacked. Double Stacked: IM-500SAB × 2, Stacking Kit HS-5530 × 1 Triple Stacked: IM-500SAB × 3, Stacking Kit HS-5530 × 2 • The bin control switch on the lowest icemaker controls all icemakers. The bin control switch and switch mount must be removed from the upper icemakers.
- Page 2 Preparing Existing Lower Icemaker 2) Remove the front panel and move the control switch to the "OFF" position and turn off the power supply. Place the icemaker disconnect (if applicable) in the off position. Lockout/Tagout to prevent the power supply from being turned back on inadvertently.
- Page 3 Upper Icemaker Installation Instructions 8) Remove the top, left, and right panels. See "II.C. How to Remove Panels" in the instruction manual. Also remove the lower rear panel. See Fig. 4. 9) Remove the protective plastic film from the panels. If the icemaker is exposed to the sun or to heat, remove the film after the icemaker cools.
- Page 4 15) Place the new ice chute provided in this kit in position as shown in Fig. 8. Secure the rear of the ice chute to the upper icemaker rear rail frame (bin control mounting bracket holes) with the new thumbscrews provided in this kit. Secure front of the ice chute to the upper icemaker front rail frame (cube guide mounting hole) with the cube guide thumbscrew removed in step 13.
- Page 5 20) At the front of the icemakers, locate the lower and upper icemakers front mounting holes. See Fig. 11. To prevent plastic shavings from entering the ice storage bin area during drilling, place a large pan or cloth under the icemakers front mounting holes.
- Page 6 23) Route the wire harness from the lower wire channel through the lower wire channel access hole with the lower icemaker actuator motor wires. Then, up into the upper icemaker between the frame and the new ice chute through the wire saddles and into the upper wire channel through the upper wire channel access hole with the upper icemaker actuator motor wires.
Need help?
Do you have a question about the HS-5530 and is the answer not in the manual?
Questions and answers