Brita PURITYHEADPLV Installation Instructions
Brita PURITYHEADPLV Installation Instructions

Brita PURITYHEADPLV Installation Instructions

Advertisement

BRITA PURITY HEAD PLV
INSTALLATION INSTRUCTIONS
Please read carefully and retain for future reference.
CONTENTS
1.

Important Information

2.

Included parts

3.
4.
1. Important Information
-
For correct operation of this appliance, it is essential to strictly observe these installation and operating instructions.
-
Do not use this product with water that is microbiologically unsafe, or with water of unknown quality without adequate disinfection before or after
this system. Installation must comply with any existing state or local plumbing codes. Some plumbing codes require the installation of water filter
systems to be carried out by a licensed plumber.
-
For COLD water use only. Maximum temperature 38°C. Minimum temperature 2°C.
-
For internal use only.
-
The inlet water pressure to this water filter housing must not exceed 900kPa (130psi).
-
A certified pressure limiting/dual check backflow prevention valve not exceeding 650kPa (95psi) must be installed on the inlet line immediately pre-
ceding this water filter housing. This valve is included with this system (see part (e) in the Included Parts section).
-
We also recommend the installation of a water hammer protection device to protect the water filter housing and its installation. Where water ham-
mer problems exist, a water hammer protection device must be installed. Symptoms of water hammer can be noisy, shuttering, and banging pipes
when water-consuming appliances are operating or taps are turned off. Should the system not be used for two days or more, flush 1-2 litres of water
through the system before consuming the water.
-
To ensure the high level of performance and protection provided from this water filter system, only use Bombora replacement cartridges which have
a maximum cartridge life of 12 months.
-
After installation, check the output water with a test strip and then test every 6-8 weeks afterwards to establish your filter life based on your average
use. The TH reading should be below low range (less than 80PPM). If you get a higher reading than this on installation, call us to discuss either adjust-
ing your bypass setting or restricting water flow further. Suggested filter cartridge change is 12 months or when the softening capacity is diminished
(over 80 PPM TH); whichever comes sooner.
2. Included Parts
a) Filter Head Inlet – 3/8" Female Thread to 3/8" BSP Quick-Connect
b) Filter Head Assembly – Brita Filter Head
c) Polypropylene Tube – 3/8" Poly Tube (White)
d) Hose Quick-Connect Fitting – 1/4" Male Thread to 3/8"
Quick-Connect Tubing
e) Pressure Limiting Valve – Stainless PLV 1/2" Female to 1/4" Female
f) Thread Seal Tape – (White)
Please Note: Brita filter cartridge is NOT provided with this kit.
bomborasupplies.com.au
b.
1300 724 249
PART # PURITYHEADPLV
c.
d.
a.
sales@bomborasupplies.com.au
e.
f.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PURITYHEADPLV and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Brita PURITYHEADPLV

  • Page 1 Hose Quick-Connect Fitting – 1/4” Male Thread to 3/8” Quick-Connect Tubing e) Pressure Limiting Valve – Stainless PLV 1/2” Female to 1/4” Female f) Thread Seal Tape – (White) Please Note: Brita filter cartridge is NOT provided with this kit. bomborasupplies.com.au 1300 724 249 sales@bomborasupplies.com.au...
  • Page 2 4. Warranty Information The PURITYHEADPLV Water Filter System is designed to operate at a maximum pressure of 900kPa (130psi) and at a maximum temperature of 38°C. Bombora Supplies warrants this system to be free from defects in material and workmanship for a period of Two (2) Years from the date of purchase.

Table of Contents