Bosch GCO 14-24 J Professional Original Instructions Manual page 17

(9) Quick release
(10) Spindle handle
(11) Assembly holes
(12) Hex key (8 mm)
(13) Base plate
(14) Clamping jaw
(15) Workpiece support for workpieces with cross sec-
tion of max. 40 x 40 mm
(16) Locking screw for angle guide
(17) Transport safety lock
(18) Tool arm
(19) Transport handle
(20) Protective guard
(21) Spark guard plate
(22) Tool spindle
(23) Clamping flange
(24) Washer
(25) Hexagon screw
Technical Data
Cut-off grinder
Article number
Rated power input
No-load speed
Soft start
Weight according to EPTA-
Procedure 01:2014
Protection class
Permitted workpiece dimensions (maximum/minimum): Permissible
workpiece dimensions
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Dimensions of suitable cutting discs
Max. cutting disc diameter
Max. cutting disc thickness
Hole diameter
Noise Information
Noise emission values determined according to
EN 62841-3-10.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 101 dB(A); sound power level
112 dB(A). Uncertainty K=3 dB.
Wear hearing protection!
The noise emission value given in these instructions has
been measured in accordance with a standardised measur-
ing procedure and may be used to compare power tools. It
may also be used for a preliminary estimation of noise emis-
sions.
Bosch Power Tools
The noise emission value given represents the main applica-
tions of the power tool. However, if the power tool is used
for other applications, with different application tools or is
poorly maintained, the noise emission value may differ. This
may significantly increase noise emissions over the total
working period.
To estimate noise emissions accurately, the times when the
tool is switched off, or when it is running but not actually be-
ing used, should also be taken into account. This may signi-
ficantly reduce noise emissions over the total working
period.
Assembly
Avoid starting the power tool unintentionally. The
u
mains plug must not be connected to the power supply
during assembly or when carrying out any kind of
work on the power tool.
Items included
Carefully remove all parts included in the delivery from their
packaging.
Remove all packing material from the power tool and the ac-
cessories provided.
Check to ensure that all the parts listed below have been
GCO 14-24 J
supplied before using the power tool for the first time:
3 601 M37 2..
– Cut-off grinder with cutting disc fitted
W 2400
– Hex key (12)
-1
min 3800
Note: Check the power tool for possible damage.
●
Before continuing to use the power tool, carefully check that
all protective devices or slightly damaged parts are working
kg 18.0
perfectly and according to specifications. Check that the
moving parts are working perfectly and without jamming;
/ II
check whether any parts are damaged. All parts must be fit-
ted correctly and all the conditions necessary to ensure
smooth operation must be met.
If the protective devices or any parts become damaged, you
must have them properly repaired or replaced by an author-
ised service centre.
Stationary or flexible mounting
mm 355
To ensure safe handling, the power tool must be
mm 3 u
mounted on a flat, stable work surface (e.g. work
mm 25.4
bench) before use.
Mounting on a work surface (see figure A)
– Use suitable screw fasteners to secure the power tool to
the work surface. Use the holes (11) to do this.
Flexible installation (not recommended)
In exceptional circumstances, if it is not possible to securely
mount the power tool on a work surface, you can improvise
by placing the feet of the base plate (13) on an appropriate
base (e.g. workbench, flat ground, etc.), without screwing
down the power tool.
English | 17
1 609 92A 5UH | (05.10.2020)