Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zetor PROXIMA PLUS 90
Summary of Contents for Zetor PROXIMA PLUS 90
- Page 2 ZETOR You are presented with a user manual amendment which covers the operation and maintenance of a new model of the PROXIMA PLUS series 2011. You are kindly asked to become familiar with the contents of this manual, even though you may be experienced in operating other tractors.
- Page 3 Technical specifications and information on construction, equipment, material, or outer appearance is valid at the moment of printing. The manufacturer reserves the right for any change.
-
Page 4: Table Of Contents
CONTENTS Page Page Proxima plus tractors ............4 Amount of oil taken from outer hydraulic drives....22 Tractors with front drive axle (4wd): ........4 *Quick couplers with dripping oil reservoir......23 Introduction ................5 Connecting and disconnecting quick couplers....23 *Tilt steering wheel............... -
Page 5: Proxima Plus Tractors
PROXIMA PLUS TRACTORS TRACTORS WITH FRONT DRIVE AXLE (4WD): Tractor Type Engine Power (kW) Z100 Z110... -
Page 6: Introduction
INTRODUCTION F205 *TILT STEERING WHEEL *TILT AND TELESCOPE STEERING lever (2) in the opposite direction than WHEEL shown by the arrow. Adjusting the angle of the wheel Tilt column of the steering wheel enables The angle can be adjusted by tilting the After adjusting, tilt the lever (2) to adjust the angle and height of the wheel after it is unlocked by moving the... -
Page 7: Control Panel On The Cab Right Piller
INTRODUCTION P+11NH127a CONTROL PANEL ON THE CAB RIGHT PILLER 1- rear PTO shaft switch 2- front shaft switch 3- two-position switch of the windscreen wiper and washer 4- rear window wiper switch 5- switch of front working lights on cab roof 6- switch of rear working lights on cab roof 7- *rear mirrors heating switch 8- *rear window defroster switch... -
Page 8: Driving Operation
DRIVING OPERATION P+11NG202 P+11G203 STARTING THE ENGINE If the glow plug indicator does not illuminate but flashes, there is an 1. Put the key in ignition - ”0” position. error of the ignition system (Igni- 2. Depress the clutch pedal. tion system error signals chap- 3. -
Page 9: Agriculture Machinery Drive
AGRICULTURE MACHINERY DRIVE E358 MAXIMUM TRANSFERED POWER Shaft Transferred Power front 1000 min 60 kW rear 1000 min full engine output 540 min full engine output 540E min full engine output... -
Page 10: Hydraulic System
HYDRAULIC SYSTEM P11N001 HYDRAULIC SYSTEM It consists of the inner and outer circuits. Gear pump is the source of pressure oil. Oil is taken from reservoir shared by gearbox and transmission. Hydraulic pump cannot be switched off. If the engine is working, the pump is on. The amount supplied is 50 liters per minute. -
Page 11: Hydraulics Control Panel
HYDRAULIC SYSTEM P+11N001 P+11N002 HYDRAULICS CONTROL PANEL WAYS TO REGULATE INNER HYDRAULIC CIRCUIT Hydraulics control panel is located in the Hydraulic system allows of three ways to regulate the lifting of the rear three-point area of the right wing. hitch: Controlling the rear three-point hitch is Position regulation (img. -
Page 12: Controlling The Inner Hydraulic Circuit
HYDRAULIC SYSTEM P+11N003 P+11N004 P+11N009 CONTROLLING THE INNER FREE (FLOATING) POSITION ADJUSTABLE STOP HYDRAULIC CIRCUIT Free (floating) position makes it possible Under default settings, it is recom- position or power regulation lever to work with tools with a support wheel. mended to set the adjustable stop (1) to lever for selecting floating position, In this position, the arms of the rear... -
Page 13: Three-Point Hitch Lowering Speed Control
HYDRAULIC SYSTEM P+11N006 E408 THREE-POINT HITCH LOWERING HYDRAULIC SYSTEM SENSITIVITY SPEED CONTROL CONTROL Three-point hitch lowering speed control Hydraulic system sensitivity control (4) (3) selects the speed of lowering the adjusts the sensitivity of the hydraulics in arms of the rear three-point hitch. Turn- power or mixed regulation. -
Page 14: Position Regulation Of The Lifting Of The Rear Three-Point Hitch
HYDRAULIC SYSTEM P+11N008 POSITION REGULATION OF THE LIFTING OF THE REAR THREE-POINT HITCH Position regulation of the lifting of the rear three-point hitch means that the tool connected to the rear three-point hitch is auto- matically kept in the same height (position) with regard to the tractor. Move lever (1) to the front position (d). -
Page 15: Power Regulation Of The Lifting Of The Rear Three-Point Hitch
HYDRAULIC SYSTEM P+11N010 POWER REGULATION OF THE LIFTING OF THE REAR THREE-POINT HITCH Power regulation of the lifting of the rear three-point hitch means that the tool connected to the rear three-point hitch is automati- cally being adjusted depending on changing soil resistance. Set the adjustable stop (5) to a position on the edge between floating position and the beginning of the range of lifting of the rear three-point hitch. -
Page 16: Mixed Regulation Of Lifting The Rear Three-Point Hitch
HYDRAULIC SYSTEM P+11N011 MIXED REGULATION OF LIFTING THE REAR THREE-POINT HITCH Mixed regulation of lifting the rear three-point hitch means that the tool connected to the rear three-point hitch is automatically be- ing adjusted depending on changing soil resistance and at the same time it prevents any increase in depth of tilling in case of smaller soil resistance. -
Page 17: Exterior Rear Hydraulic Arms Controls
HYDRAULIC SYSTEM P+11N016 P+11N012 EXTERIOR REAR HYDRAULIC ARMS CONTROLS OUTER HYDRAULIC CIRCUIT Exterior rear hydraulic arms controls are located on the rear right wing. They make it It supplies pressure oil for hydraulic de- easier for the operator to conncet tools by controlling the movements of the lower vices on outer drives of hydraulics ended drawbars of the three-point hitch from the outside. -
Page 18: Outer Hydraulic Circuit Controls
HYDRAULIC SYSTEM P+11N015 OUTER HYDRAULIC CIRCUIT CONTROLS Outer hydraulic circuit controls are located on the right wing. lever (a) controls the lower section of distributor – quick couplers (1) and (2) lever (b) controls the central section of distributor – quick couplers (3) and (4) lever (c) controls the upper section of distributor –... -
Page 19: Locking Control Levers
HYDRAULIC SYSTEM P+11N014 LOCKING CONTROL LEVERS Outer hydraulic circuit control levers are locked in neutral (N) position. To unlock them, raise the lock control (1) and turn it to a stop point in the direction shown by the arrow. To lock them again, move the levers to neutral (N) position and turn the lock control in the opposite direction than shown by the arrow to a stop point and... -
Page 20: Different Functions Of Outer Hydraulic Circuit Control Levers
HYDRAULIC SYSTEM P+11N017 DIFFERENT FUNCTIONS OF OUTER HYDRAULIC CIRCUIT CONTROL LEVERS There are four positions of the lever (a): N - Neutral position. Quick coupler drives (1) and (2) are closed and oil in the hydraulic appliance connected is blocked. Lever (a) is locked in this position. -
Page 21: Different Functions Of Outer Hydraulic Circuit Control Levers
HYDRAULIC SYSTEM P+11N018 DIFFERENT FUNCTIONS OF OUTER HYDRAULIC CIRCUIT CONTROL LEVERS There are four positions of the lever (b): N - Neutral position. Quick coupler drives (3) and (4) are closed and oil in the hydraulic appliance connected is blocked. Lever (b) is locked in this position. -
Page 22: Different Functions Of Outer Hydraulic Circuit Control Levers
HYDRAULICKÉ ZAŘÍZENÍ P+11N019 DIFFERENT FUNCTIONS OF OUTER HYDRAULIC CIRCUIT CONTROL LEVERS There are four positions of the lever (b) which controls quick couplers (5) and (6): N - Neutral position. Quick coupler drives (5) and (6) are closed and oil in the hydraulic appliance connected is blocked. Lever (c) is locked in this position. -
Page 23: Amount Of Oil Taken From Outer Hydraulic Drives
HYDRAULIC SYSTEM Working area: in flat terrain Max. amount of oil taken: 20 liters Gearbox filling: standard filling within the range shown by lines (A) Working area: in a slope Max. amount of oil taken : 13 liters Gearbox filling : standard filling within the range shown by lines (A) Working area : in flat terrain E413... -
Page 24: Quick Couplers With Dripping Oil Reservoir
HYDRAULIC SYSTEM P+11N020 *QUICK COUPLERS WITH DRIPPING CONNECTING AND DISCONNECTING OIL RESERVOIR QUICK COUPLERS On request, dripping system for holding When connecting or disconnecting leakage oil can be installed. Check the quick couplers, be careful about reservoir regularly; if it is full, empty it leakage oil which rests on the cou- ecologically. -
Page 25: Connecting Machinery And Tools To Outer Hydraulic Circuit
HYDRAULIC SYSTEM CONNECTING MACHINERY AND TOOLS TO OUTER HYDRAULIC CIRCUIT Connecting a double acting cylinder A double acting cylinder must always be connected to quick couplers of one section. Connecting machinery and tools assembled from more parts When working with agriculture machinery which is assembled from more parts (combinators, scrubbers, or harrows) where the edge frame is hinged to the central frame because it is diagonally folded during transport by independent hydraulic cylinders which are controlled by outer hydraulic circuit of the tractor, it is recommended to connect the lifting arms of the cylinders to quick couplers (3) and (5) which are equipped with a one-way valve. -
Page 26: Hitches
HITCHES P+11N021 COTROLLING FRONT THREE-POINT HITCH The hitch is equipped with two single acting hydraulic cylinders which are supplied with oil from an additional hydraulic distributor. To lift or lower, use lever (b) of the additional dis- tributor. 3 position lifting 4 position lowering... -
Page 27: Electric Installation
ELECTRIC INSTALLATION Location of fuses in fuse box Posi- Fuse System to which it applies tion value warning lights chopper, breaking lamps horn, warning beacon front drive axle control, differential lock control, dashboard power supply high beam headlamps and indicator side lamps, dashboard lamps, license plate lamps right side lamps, rear working lamp... -
Page 28: Maintenance
MAINTENANCE CHANING FILLINGS AND FILTERS with a new tractor or with a tractor after a general repair and then always after reach- Motohours ing..motohours Changing engine oil Changing insertion of oil cleaner Changing insertion of fuel cleaner Changing insertion of air cleaner 1000 Changing safety insertion piece of air cleaner 2000... -
Page 29: Maintenance
MAINTENANCE P11004 P11N005 CHANGING SUCTION FILTER CHANING INSERTION OF OIL CLEANER Suction filter is located on the left side of gearbox. To change the filter, empty the oil from gearbox. Oil cleaner is located on the left side of gearbox. Oil flows out of the hoses while changing the filter. -
Page 30: Adjusting
ADJUSTING P+11NE751 STRETCHING THE V-BELT If the V-belt is stretched correctly, the belt flexure must be 5.5 mm when apply- ing 25 N pressure on one belt. Stretch the V-belt as recommended after loosening alternator fastening bolts (1,... -
Page 31: Technical Specifications
TECHNICAL SPECIFICATIONS LIFT CAPACITY OF THE THREE-POINT HITCH Lift capacity at the end of the lower drawbars of the rear thee- point hitch during the entire lift while using up the maximum pressure with 2 outer cylinders - *cylinder 75mm in diameter (kN) Lift capacity at the end of the lower drawbars of the front three- point hitch during the entire lift while using up the maximum pressure (kN) -
Page 32: Index
INDEX Adjustable stop Lift capacity of the three-point hitch Adjusting Locking control levers Agriculture machinery drive Amount of oil taken from outer hydraulic drives Maintenance Maintenance Connecting and disconnecting quick couplers Mixed regulation of lifting the rear three-point hitch Connecting machinery and tools assembled from more parts Connecting machinery and tools to outer hydraulic circuit Outer hydraulic circuit Control panel on the cab right piller... - Page 33 Supllement Operator's manual Proxima Plus 90 Proxima Plus 100 Proxima Plus 110 Edition: 1-100-2011 Publication No.: 222.212.580 Zetor Tractors a.s. Department of Technical Documentation Trnkova 111 632 00...