Advertisement
Quick Links
Dear customer
st
LAPIS Semiconductor Co., Ltd. ("LAPIS Semiconductor"), on the 1
day of October,
2020, implemented the incorporation-type company split (shinsetsu-bunkatsu) in which
LAPIS established a new company, LAPIS Technology Co., Ltd. ("LAPIS
Technology") and LAPIS Technology succeeded LAPIS Semiconductor's LSI business.
Therefore, all references to "LAPIS Semiconductor Co., Ltd.", "LAPIS Semiconductor"
and/or "LAPIS" in this document shall be replaced with "LAPIS Technology Co., Ltd."
Furthermore, there are no changes to the documents relating to our products other than
the company name, the company trademark, logo, etc.
Thank you for your understanding.
LAPIS Technology Co., Ltd.
October 1, 2020
Advertisement
Related Manuals for LAPIS Semiconductor ML7344
Summary of Contents for LAPIS Semiconductor ML7344
- Page 1 LAPIS established a new company, LAPIS Technology Co., Ltd. (“LAPIS Technology”) and LAPIS Technology succeeded LAPIS Semiconductor’s LSI business. Therefore, all references to "LAPIS Semiconductor Co., Ltd.", "LAPIS Semiconductor" and/or "LAPIS" in this document shall be replaced with "LAPIS Technology Co., Ltd."...
- Page 2 FEXL_SubGHz_EVA_startguide-02 Sub-GHz LSI Evaluation Kit Start Guide Issue Date: Nov 20 , 2018...
- Page 3 Products. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of LAPIS Semiconductor or any third party with respect to the information contained in this document; therefore LAPIS Semiconductor shall have no responsibility whatsoever for any dispute, concerning such rights owned by third parties, arising out of the use of such technical information.
- Page 4 The manual shown in the following other than this document is prepared. Please check if needed. Datasheet Design Guide Simple MAC User’s Manual Wireless Control Tool3 (WCT3) User’s Manual This supports the following evaluation board. ・ML7344 ・ML7406 ・ML7345 ・ML7345C ・ML7345D ・ML7404 ・ML7414 ・ML7411 FEXL_SubGHz_EVA_startguide-02...
-
Page 5: Setup Flow
Sub-GHz LSI Evaluation Kit Start Guide 1. Attention on the handling of this product This product is evaluation kit. It is available for evaluation only. Any responsibility cannot be taken about building this product into other products. Please use the application software of this product with the PC with which Japanese version Windows 7 is installed. - Page 6 Sub-GHz LSI Evaluation Kit Start Guide 2.1. Control Board Setting This section describes the control board setting. 7 SEG LED Figure 1: Control Board Overview Table 1: Detailed Description of Control Board Initial Symbol Name Function configuration Main power supply setup USB electric supply (1-2) and external electric supply (2-3) External electric supply setup to JP1...
- Page 7 Sub-GHz LSI Evaluation Kit Start Guide There are four modes of operation in this evaluation kit, and setup of a jumper differs for each mode. Please set up a jumper correctly after referring to the following table. Table 2: Mode of operation and a jumper setup Function Mode Function...
- Page 8 RESETN_TEST open For micro controller JP102 REGPDIN_TEST open For micro controller JP104 RESETN_PU open Micro controller and evaluation board power supply simultaneously JP105 MCU_VDD short (3.3V) If these are individual power supplied, open short(ML7344) JP118 VTUNE open(except for ML7344) FEXL_SubGHz_EVA_startguide-02...
- Page 9 Sub-GHz LSI Evaluation Kit Start Guide The ML7406 evaluation board is connected with the control board as shown below. JP101 JP105 JP10 Connect by 26pin connecter USB port(Micro B) JP117 SW1 Reset Switch Supply 3.3V power ANT1 ANT2 JP102 * When you do not use diversity function for Sub-GHz, please use ANT1. Figure 3: ML7406 Evaluation Board Connection Overview Table 4: Evaluation board jumper setting table (ML7406) Recommended Jumper...
- Page 10 Sub-GHz LSI Evaluation Kit Start Guide The ML7411 evaluation board is connected with the control board as shown below. JP16 JP18 JP10 JP11 Connect by 26pin connecter USB port(Micro B) 2.4GHz TX (ANT4) 2.4GHz RX SW1 Reset Switch (ANT3) Supply 3.3V power Sub-GHz(ANT1) JP17 JP13...
- Page 11 Sub-GHz LSI Evaluation Kit Start Guide 2.3. How to check connection You can control the evaluation board using “WCT3” or “Tera Term”. The connection procedure when using each tool is shown below. “WCT3” is a GUI tool to control Sub-GHz LSI evaluation boards which are made in LAPIS Semiconductor Co., Ltd.
- Page 12 Sub-GHz LSI Evaluation Kit Start Guide For details of WCT3, please refer to “Wireless Control Tool3 User’s manual”. (2) Tera Term (terminal software) Supply 3.3V power supply. Reset the control board. Start the terminal software (Tera Term). Set the terminal software. * No prompt will be displayed by power-on, terminal software setting or reset.
- Page 13 Sub-GHz LSI Evaluation Kit Start Guide Figure 9: Tera Term Terminal Setting Screen FEXL_SubGHz_EVA_startguide-02...
-
Page 14: Revision History
, 2018 – – Initial version startguide-01 Add ML7411 in support product list Add jumper setting table for – ML7344/ML7345/ML7345C/ML7345D/ML7404/ML7414 6FEXL_SubGHz_EVA Nov 20 , 2018 – Add jumper setting table for ML7406 _startguide-02 – Add jumper setting table for ML7411 Evaluation board –...
Need help?
Do you have a question about the ML7344 and is the answer not in the manual?
Questions and answers