Advertisement
Quick Links
Dear customer
st
LAPIS Semiconductor Co., Ltd. ("LAPIS Semiconductor"), on the 1
day of October,
2020, implemented the incorporation-type company split (shinsetsu-bunkatsu) in which
LAPIS established a new company, LAPIS Technology Co., Ltd. ("LAPIS
Technology") and LAPIS Technology succeeded LAPIS Semiconductor's LSI business.
Therefore, all references to "LAPIS Semiconductor Co., Ltd.", "LAPIS Semiconductor"
and/or "LAPIS" in this document shall be replaced with "LAPIS Technology Co., Ltd."
Furthermore, there are no changes to the documents relating to our products other than
the company name, the company trademark, logo, etc.
Thank you for your understanding.
LAPIS Technology Co., Ltd.
October 1, 2020
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for LAPIS Semiconductor ML7344
Summary of Contents for LAPIS Semiconductor ML7344
- Page 1 LAPIS established a new company, LAPIS Technology Co., Ltd. (“LAPIS Technology”) and LAPIS Technology succeeded LAPIS Semiconductor’s LSI business. Therefore, all references to "LAPIS Semiconductor Co., Ltd.", "LAPIS Semiconductor" and/or "LAPIS" in this document shall be replaced with "LAPIS Technology Co., Ltd."...
-
Page 2: Start Guide
FEXL7344_7406EVA_startguide-03 ML7344, ML7406EVA Start Guide Issue Date: Dec 19, 2014... - Page 4 ML7344, 7406EVA Start Guide NOTES No copying or reproduction of this document, in part or in whole, is permitted without the consent of LAPIS Semiconductor Co., Ltd. The content specified herein is subject to change for improvement without notice. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products.
- Page 5 ML7344, 7406EVA Start Guide Introduction Thank you very much for purchasing products of our company. Before using this product, please use correctly after reading this “start guide”. Moreover, please keep it carefully even after reading this. This start guide indicates enclosure attachment ant the connection method.
-
Page 6: Setup Flow
Please prepare a stabilized power supply and serial communication software (TeraTerm). A USB UART IC (FT232R), which is made by FTDI, is placed on the control board. Please download a USB device driver from http://www.ftdichip.com. - ML7344, ML7406 Control Board… 1 - ML7344/ML7406 Evaluation Board… 1 - USB(A-MicroB) Cable… 1 - Antenna…... - Page 7 ML7344, 7406EVA Start Guide 2.1. ML7344, ML7406 Control Board Setting This section describes the control board setting. 7 SEG LED Figure 1: Control Board Overview Table 1: Detailed Description of Control Board Initial Symbol Name Function configuration Main power supply setup...
- Page 8 ML7344, 7406EVA Start Guide There are four modes of operation in this evaluation kit, and setup of a jumper differs for each mode. Please set up a jumper correctly after referring to the following table. Table 2: Mode of operation and a jumper setup...
- Page 9 ML7344, 7406EVA Start Guide 2.2. ML7344, ML7406 Evaluation Board Setting Procedure The ML7344 evaluation board is connected with the control board as shown below. Connect by 26pin connecter SW1 Reset Switch Supply 3.3V power Figure 2: ML7344 Evaluation Board Connection Overview The ML7406 evaluation board is connected with the control board as shown below.
- Page 10 ML7344, 7406EVA Start Guide [Connection verification procedure] Supply 3.3V power supply. Reset the control board. Start the terminal software (Tera Term). Set the terminal software. (For terminal settings, refer to "2.4 Terminal Setting".) * No prompt will be displayed by power-on, terminal software setting, or reset.
- Page 11 ML7344, 7406EVA Start Guide 2.3. ML7344, ML7406 Evaluation Board Jumper Setting ML7344 and ML7406 evaluation board jumper function and recommended setting are as following. Table 3: Evaluation board jumper setting table Recommended Jumper JP No. Silk Remarks Setting RESETN_MCU short...
- Page 12 ML7344, 7406EVA Start Guide 2.4. Terminal Setting 2.4.1. Tera Term Setting The Tera Term serial port settings are shown below. The red frame indicates required settings. Use Tera Term version 4.63 or higher. Figure 5: Tera Term Serial Port Setting Screen...
- Page 13 ML7344, 7406EVA Start Guide 2.4.2. Wireless Control Tool Setting Wireless Control Tool (WCT) is able to control ML7344 Simple MAC (Note: WCT is not used for ML7406.). WCT serial port setting is below. You must set category in red box.
-
Page 14: Revision History
ML7344, 7406EVA Start Guide Revision History Page Document No. Issue Date Description Previous Edition New Edition FEXL7344_7406EVA_startguide-01 2013.7.25 – – First edition issued Added Control board FEXL7344_7406EVA_startguide-02 2014.5.8 setting Added Table of jumper setting Added WCT setting Modified assembled FEXL7344_7406EVA_startguide-03 2014.12.19...
Need help?
Do you have a question about the ML7344 and is the answer not in the manual?
Questions and answers