Subscribe to Our Youtube Channel
Related Manuals for LAPIS Semiconductor ML7344
Summary of Contents for LAPIS Semiconductor ML7344
- Page 1 FEXL7344_7406EVA_startguide-02 ML7344, ML7406EVA Start Guide Issue Date: May 8, 2014...
- Page 3 ML7344, 7406EVA Start Guide NOTES No copying or reproduction of this document, in part or in whole, is permitted without the consent of LAPIS Semiconductor Co., Ltd. The content specified herein is subject to change for improvement without notice. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products.
- Page 4 ML7344, 7406EVA Start Guide Introduction Thank you very much for purchasing products of our company. Before using this product, please use correctly after reading this “start guide”. Moreover, please keep it carefully even after reading this. This start guide indicates enclosure attachment ant the connection method.
-
Page 5: Attention On The Handling Of This Product
By shipment time, mounting parts etc may differ from a photograph in part. Please prepare a stabilized power supply, a RS-232C cable (straight), and serial communication software (TeraTerm). - ML7344, ML7406 Control Board… 1 - ML7344/ML7406 Evaluation Board… 1 - Power Supply Cable… 1 - CD-ROM…... - Page 6 ML7344, 7406EVA Start Guide 2.1. Control Board Setting This section describes the control board setting. Figure 1: Control Board Overview Table 1: Detailed Description of Control Board Number Symbol Function In case of CN14 short, SW1 switch is set to CN13 side (lower side in Fig.16) : set CPU reset SW1 switch is set to “SW1”...
- Page 7 ML7344, 7406EVA Start Guide 2.2. ML7344, ML7406 Evaluation Board Setting Procedure The ML7344 evaluation board is connected with the control board as shown below. Connect by 26pin connecter SW1 Reset Switch Supply 3.3V power Figure 2: ML7344 Evaluation Board Connection Overview The ML7406 evaluation board is connected with the control board as shown below.
- Page 8 ML7344, 7406EVA Start Guide ML7344 and ML7406 evaluation board jumper function and recommended setting are as following. Table 2: Evaluation board jumper setting table JP No. Silk Jumper Setting Remarks RESETN_MCU short For micro controller REGPDIN_MCU short For micro controller...
-
Page 9: Terminal Setting
ML7344, 7406EVA Start Guide 2.3. Terminal Setting 2.3.1. Tera Term Setting The Tera Term serial port settings are shown below. The red frame indicates required settings. Use Tera Term version 4.63 or higher. Figure 4: Tera Term Serial Port Setting Screen... - Page 10 ML7344, 7406EVA Start Guide 2.3.2. Wireless Control Tool Setting Wireless Control Tool (WCT) is able to control ML7344, ML7406 Simple MAC. WCT serial port setting is below. You must set category in red box. Figure 6: WCT serial port setting If you push OK button on WCT serial port setting window, WCT main window is popd up.
- Page 11 ML7344, 7406EVA Start Guide Connection verification procedure Supply 3.3V power supply. Reset the control board. Start the terminal software (Tera Term). Set the terminal software. (For terminal settings, refer to "2.3 Terminal Setting".) * No prompt will be displayed by power-on, terminal software setting, or reset.
-
Page 12: Revision History
ML7344, 7406EVA Start Guide Revision History Page Document No. Issue Date Description Previous Edition New Edition FEXL7344_7406EVA_startguide-01 2013.7.25 – – First edition issued Added Control board FEXL7344_7406EVA_startguide-02 2014.5.8 setting Added Table of jumper setting Added WCT setting FEXL7344_7406EVA_startguide-02...
Need help?
Do you have a question about the ML7344 and is the answer not in the manual?
Questions and answers