Subscribe to Our Youtube Channel
Related Manuals for GreenWorks Pro 2502402
Summary of Contents for GreenWorks Pro 2502402
- Page 1 2502402 LAWN MOWER OPERATOR MANUAL TONDEUSE À GAZON MANUEL D'UTILISATION www.greenworkstools.com/80v-pro LMB408...
-
Page 2: Table Of Contents
English Purpose......... 2 Install the battery pack....... 7 Remove the battery pack......7 Overview........2 Operation........8 Read all instructions...... 2 Start the machine........8 Children and Bystanders......2 Stop the machine........8 General Operation........2 Operate the self-propel system....8 Slope Operation......... 3 Empty the grass catcher......8 Service/Maintenance........4 Operate on slopes........ -
Page 3: Purpose
English PURPOSE NOTE When using electric lawn mowers, basic safety This machine is used for domestic lawn mowing. The precautions should always be followed to reduce the cutting blade must be approximately parallel to the risk of fire, electric shock, and personal injury. These ground. -
Page 4: Slope Operation
English • Before and while moving backwards with the • If the equipment should start to vibrate abnormally, mower, look behind and down for small children and immediately stop the motor, remove the battery and other people. check for the cause. Vibration is generally a warning that the machine is not functioning properly. -
Page 5: Service/Maintenance
English • Do not mow near drop-offs, ditches or Symbol Name Explanation embankments; you could lose your footing or Alternating balance. Type of current Current • Do not mow slopes greater than 15 degrees, as shown on the slope gauge. Direct Cur- Type or a characteristic •... -
Page 6: Risk Levels
English RISK LEVELS WARNING If the battery pack cracks or breaks, with or without The following signal words and meanings are intended leaks, do not recharge it and do not use. Discard it to explain the levels of risk associated with this product. and replace with a new battery pack. -
Page 7: Unfold The Lower Handle
English UNFOLD THE LOWER HANDLE 4. Do the same operation on the other side. INSTALL THE GRASS CATCHER 1. Pull and turn the handle knobs (13) 90°. 2. Unfold the lower handle (3). 1. Remove the mulch plug. 3. Line up the handle knobs in one of the three positions (14) on the brackets. -
Page 8: Install The Side Discharge Chute
English INSTALL THE SIDE DISCHARGE INSTALL THE BATTERY PACK CHUTE WARNING • If the battery pack or charger is damaged, replace the battery pack or the charger. • Stop the machine and wait until the motor stops CAUTION before you install or remove the battery pack. •... -
Page 9: Operation
English OPERATE THE SELF-PROPEL 3. Push and hold the battery release button (24). SYSTEM 4. Remove the battery pack (25) from the machine. NOTE OPERATION The machine is built with a thermal protector to stop WARNING the self-propelled motor when overload occurs. It’s a device calibrated to open the self-propelled motor Wear eye protection during operation. -
Page 10: Operate On Slopes
English OPERATE ON SLOPES CAUTION Do not use strong solvents or detergents on the plastic WARNING housing or components. Do not mow on the slopes with incline more than 15°. If you are not comfortable, do not mow on a slope. GENERAL MAINTENANCE •... -
Page 11: Stand The Machine On End
English TROUBLESHOOTING • Make sure that the machine does not have loose or damaged parts. If it is necessary, do these steps/ instructions: Problem Possible cause Solution • Replace the damaged parts. The handle is The bolts are not Adjust the height •... -
Page 12: Technical Data
English used for personal use that have not been hired or Problem Possible cause Solution rented for industrial/commercial use, and that have The machine The blade height Increase the been maintained in accordance with the instructions in stops during is too low. blade height. -
Page 13: Exploded View
English EXPLODED VIEW 77 78 73 74 70 71 54 55 56 57 49 50 46 47 32202390 Bolt 341281179 8” Wheel assembly 332211179 Washer 311021179 Front wheel axle 341031531A 10” Wheel assembly 341041531 Big gear 32204113 Screw 341021531B Dust cover 3220505D Screw 341221531... - Page 14 English 321011531 Bearing 33206153B Rear wheel axle 32905302A Retaining ring 332071531 Small gear 332131531 Press plate 311033451 Reducer 33401222 Torsinal spring 3290135 Cotter pin 333111555 Height adjustment bar assembly 341211179 Height adjustment handle housing (left) 322041546 Screw 341221179 Height adjustment handle housing (right) 3220343 332011179 Height adjustment tension spring...
- Page 15 English 332041531D Deck 333031577 Right raised plate welding 312011560 Mechanical vertical switch assembly 342031179 Washer 3290506 Clip washer 332021179 Rear cover axle 341061577 Rubber plug 332111179 Torsinal spring (rear cover) 341251179A Rear cover 32243563 341261179 Bolt 333041179D Blade 341191179B 361011511W Motor C1100617-00 Power head assembly...
Need help?
Do you have a question about the 2502402 and is the answer not in the manual?
Questions and answers