Installation Instruction - Siemens ISRW6-12 Manual

Wireless outdoor siren

Hide thumbs

Table Of Contents

Table of Contents

Available languages

English

Before starting to install and work with this

device, please read the Safety Instructions.

Scope of delivery

ISRW6-12 wireless outdoor siren

Non-rechargeable 3.6 V battery

Description

The wireless outdoor siren is an external warning

device for outdoor use, which is controlled by a

Si2Way wireless module (e.g. IRFW6-12), gateway

(e.g. IEGW6-12) or panel.

It indicates alarms using PIEZO siren and/or power

LED. It can also be configured to signal arming and

disarming by flashing and/or beeping.

Installation

Opening the unit

Remove the 2 pivot screws (Fig. 2).

Remove the cover (Fig. 3).

Setting the jumpers

Set the jumpers A-D to the desired position (see

table Jumper settings for explanations).

Mounting the base

Choose a suitable location for the installation.

Make sure that this location is within the radio

coverage of the respective Si2Way radio

device.

It is recommended that the siren unit is

installed on a flat surface in a prominent

location.

Place the unit on the installation surface and

mark 4 holes (Fig. 4).

Mount the unit onto the installation surface.

Use only the screws and plugs supplied.

Connecting

Risk of explosion if battery is replaced by an

incorrect type.

It is necessary to insert the battery in any case,

even if the siren is powered thanks to the

external power source.

Upon battery connection, the battery will beep

and flash for about 30 sec. This behaviour is

normal, and the siren will go into normal mode

after this warm-up phase is over.

Ensure that the siren is connected to the Piezo

connector (Fig. 6 item 5).

Insert the battery in the battery holder (Fig. 5)

making sure the polarity is correct (+) (-).

Connect the battery cable into the battery

connector (Fig. 6 item 3).

Optional: Connect the +12 V external power

cable (Fig. 6 item 4).

Replace the white plastic cover on the base and

secure it with the 2 pivot screws. This will push

down the tamper switch (Fig.6, item 6). Be

careful NOT to lift up the plastic cover once it

has been put in place, otherwise a tamper will

be triggered and the siren will go on.

Connections (Fig. 6)

No.

Description

Learn Learn button

J A-D

Jumpers

BAT

Battery connector

+12V- 12 V DC power supply terminal input

Piezo Piezo connector

Tamper

Power LED

Jumper settings (Fig. 6 item 2)

Jumper Set

Output 2

Flashes upon

Arm/Disarm

Beeps with

Arm/Disarm

Time out: 15 min.

Make sure that Jumper A setting corresponds

to the siren output configuration on the panel.

Jumper A is used for IC 60 panels only

For Sintony 100-400: make sure that "external

bell at RF confirmation" is set to "yes"

Enrollment

Put the Si2Way wireless module/gateway/panel

into ENROL mode (refer to the device

documentation).

Press the learn button (Fig. 6 item 1) on the

siren.

Wait for indication of a successful learning on the

Si2Way radio module/gateway/panel.

A siren can be enrolled with one Si2Way radio

wireless module/gateway/panel only.

Battery exchange

To change the battery, make sure to cut off the

power supply on the external power cable first (if

applicable).

AS YOU OPEN THE SIREN HOUSING, a

tamper alarm will be triggered and THE SIREN

WILL BE ACTIVATED (use ear plugs if needed).

To stop the siren, remove the battery cable from

its connector. Then change the battery and

reconnect the battery cable.

Close the housing and do not forget to reset the

external power supply (if applicable).

Unenrollment

If you would like to unenrol a siren from the system,

please refer to the Si2Way wireless module/

gateway/panel documentation. You should then

erase the siren's memory:

Disconnect the battery from the BAT connector.

Press the "Learn" button and reconnect the

Not set

battery while keeping the "Learn" button pressed.

Output 1

Keep the "learn" button pressed until the LED

Does not flash upon

flashes.

Arm/Disarm

Only then will it be possible to re-enrol the siren with

Does not beep upon

another Si2Way wireless module/gateway/panel.

Arm/Disarm

Technical Data

Time out: 2 min.

Radio protocol

Radio frequency

Wireless range

Siren output level

Battery lifetime

Battery

Housing protection

Air humidity

Operating temperature -20 to +70°C

Storage temperature

Siemens Security Products hereby declares that this

product is in compliance with the essential

requirements and other relevant provisions of

Directive 1999/5/EC on Radio and

Telecommunications Terminal Equipment (R&TTE)

and 2004/108/EC on Electromagnetic Compatibility

(EMC).

The EC Declaration of Conformity is available from

your Siemens sales office or:

Siemens AB, Security Products, Englundavägen 7,

SE-171 24 Solna, Sweden

For more detailed instructions please refer to the

manual of the respective Si2Way wireless module/

gateway/panel.