Each Setting And Adjustment; Tel 13942296513; How To Save And Load The Settings Using Backup Function With Usb Memory - Pioneer SC-37 Service Manual

1

8. EACH SETTING AND ADJUSTMENT

QQ
3 7 63 1515 0

8.1 HOW TO SAVE AND LOAD THE SETTINGS USING BACKUP FUNCTION WITH USB MEMORY

[Introduction]
A
This model is capable of saving the set values stored in the MAIN Ucom of DIGITAL MAIN
ASSY in the USB and loading them in a new DIGITAL MAIN ASSY.
(Note that MAIN Ucom should normally operate to enable this function.)
When replacing DIGITAL MAIN ASSY, execute the above mentioned processes.
[Data that can be saved/cannot be saved]
The following data can not be saved. Data other than these can be saved.
Last memory for turning ON/OFF the Main power and power supply for ZONE2 and ZONE3
Last memory for inputting the Main power, ZONE2 and ZONE3
Setting for controlling HDMI
B
Remote control ID
Setting for RF remote control (EXPANSION Setup)
Setting for Network Standby
Data to be save upon the operation of protection circuit
Settings for HMG (Only for SC-37, SC-LX83 system: Because BridgeCo is used.)
Preset Memory, Favorite, Recently played, etc.
(As the data saved by EVENT Ucom is on the DISPLAY ASSY,
the data cannot be deleted unless Assy is replaced at the same time.)
[Requirements for USB memory]
USB memory to be used should meet the following requirements.
Compatible with USB Mass storage Class
C
With a file system of FAT(FAT32)
[File saving format]
Files are to be saved in the following format: Model number_backup version.extension(avr)
Example: SC-37_BK01.avr
TE
L 13942296513
[How to save in the USB memory from AV amplifier]
1. Insert the usable USB memory into the USB terminal when the main device is off.
2. Enter the SERVICE MODE and select [USB BAK
(See [6.1 TEST MODE] for how to enter the SERVICE MODE.)

3. Select [USB BAK
4. Saving in the USB starts and the main device automatically goes off after the normal completion ([COMPLETE]
is displayed.).
D
5. Remove the USB and saving is finished.
*1. If the following errors occur after "SAVE" is executed, error message will be displayed and "SAVE" will be stopped
and the power will be turned off.
Ejecting of USB device
Short capacity of USB device
Error during writing in the USB device (Read Only or defective Sector, etc.)
*2. If the same file name exists in the USB, overwriting will be automatically executed.
[How to write into AV amplifier from the USB memory]
1. Insert the USB with the saved file into the USB terminal when the main device is off.
2. Enter the TEST MODE and select [USB BAK
(See [6.1 TEST MODE] for how to enter the TEST MODE.)
E

3. Select [USB BAK
4. Saving in the main device starts and it automatically goes off after the normal completion
([COMPLETE] is displayed.).
5. Remove the USB and loading is finished.
* If the following errors occur after "LOAD" is executed, error message will be displayed and "LOAD" will be stopped and
the power will be turned off.
No setting file
www
Mismatching between the setting file and the specification of the A/V RECEIVER type to be loaded back
Error due to Checksum, Signature Check, and Size Check
Ejecting of USB device (during reading of the setting file)
F
90
1
http://www.xiaoyu163.com
2
Contents to save

 
SAVE? ] with keys and press [ENTER].

HOLD
 
LOAD? ] with keys and press [ENTER].
x ao
y
. i
2
http://www.xiaoyu163.com
3
8
Q Q
3 6 7 1 3
 
HOLD ] with keys.
 
] with keys.
u163
.
SC-37
3
4
2 9 9 4 2 8
Destination to save
EVENT Ucom
BridgeCo IC
1 5 0 5 8 2 9 9 4
m
co
4
9 9
2 8 9 9