Pioneer SC-37 Service Manual page 14

1
QQ
3 7 63 1515 0
10 Receiver Control buttons
Set the remote control operation selector switch to
A
RECEIVER first to access:
STATUS – Press to check selected receiver settings.
PHASE CTRL – Press to switch on/off Phase Control
or Full Band Phase Control.
CH LEVEL – Press repeatedly to select a channel,
then use  to adjust the level.
THX – Press to select a Home THX listening mode.
PQLS – Press to select the PQLS setting.
AUTO/ALC/DIRECT – Switches between Auto
Surround, Auto Level Control, Optimum
Surround mode and Stream Direct mode.
B
STEREO – Switches between stereo playback and
Front Stage Surround Advance modes.
STANDARD – Press for Standard decoding and to
switch various modes (
ADV SURR – Use to switch between the various
surround modes.
SIGNAL SEL – Use to select an input signal.
SLEEP – Use to put the receiver in sleep mode and
select the amount of time before sleep.
DIMMER – Dims or brightens the display.
A.ATT – Attenuates (lowers) the level of an analog
input signal to prevent distortion.
C
SBch – With this receiver, SBch cannot be used.
MCACC – Press to switch between MCACC presets
HDMI OUT – Switch the HDMI output terminal.
TE
L 13942296513
11 LIGHT
Press to turn on/off the illumination for the buttons.
12 Remote control operation selector switch
Set to RECEIVER to operate the receiver, TV or SOURCE
to operate the TV or the source device.
When this switch is set to RECEIVER , the receiver can be
D
controlled (used to select the white commands). Also use
this switch to set up surround sound.
Note
1 Press and hold in the LIGHT button for 5 seconds to change the illumination mode 1 or 2. When set to LIGHT MODE 2 (default), the
illumination only lights when the remote control LIGHT button is pressed. When switched to LIGHT MODE 1 , the illumination lights whenever
buttons are operated. Setting LIGHT MODE 1 will shorten the service life of the batteries.
2 The display lights when a remote control operation is performed, then turns off after 20 seconds if no other operation is performed. When in
E
the Remote Setup mode, the setup is canceled and the display turns off if no operation is performed for 1 minute.
3 • This is displayed when an RF adapter is connected to the receiver and paired with the remote control.
• Depending on the communications environment, two-way communications may not work well and the remote control display may not reflect
the receiver's status.
www
F
14
1
http://www.xiaoyu163.com
2
Pro Logic, Neo:6, etc.).
1
x ao
y
. i
2
http://www.xiaoyu163.com
3
8
13 VOL +/–
Use to set the listening volume.
14 MUTE
Mutes the sound or restores the sound if it has been
muted (adjusting the volume also restores the sound).
Remote control display
Remote control display for infrared signal
transmission (default)
1 2 3
MAIN
iPod/USB
Remote control display for RF two-way
3
communications
1 2 3
MAIN
AV RECEIVER
VIDEO
Q Q
3 6 7 1 3
1. Adv MCACC
8 9 10
1 Remote control operating zone indicator
This indicates which zone the remote control is currently
set to operate. The display indicates the setting of the
MULTI-ZONE operation selector switch.
Only when RF two-way communications:
The box display here indicates the communication status
between this remote control unit and the receiver.
(White box with black letters): Two-way
MAIN
communications are established and the receiver's
power is on.
u163
.
SC-37
3
4
2 9 9 4 2 8
2
4 5 6
IR SOURCE
7
4
5 6
RF RCV CTRL
+12.
0dB
1 5 0 5 8 2 9 9 4
11 12
m
co
4
9 9
2 8 9 9