Stanley TP08 User Manual

Stanley TP08 User Manual

Hydraulic trash pump
Hide thumbs Also See for TP08:

Advertisement

TP08
HYDRAULIC
TRASH PUMP
(TP0813, TP08013H, TP08013W)
USER MANUAL
Safety, Operation and Maintenance
© 2014 STANLEY Black & Decker, Inc.
New Britain, CT 06053
U.S.A.
66364 1/2021 Ver. 24

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TP08 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Stanley TP08

  • Page 1 TP08 HYDRAULIC TRASH PUMP (TP0813, TP08013H, TP08013W) USER MANUAL Safety, Operation and Maintenance © 2014 STANLEY Black & Decker, Inc. New Britain, CT 06053 U.S.A. 66364 1/2021 Ver. 24...
  • Page 2 Provisiones especiales: Disposizioni speciali: Representative in the Union: Patrick Vervier, Stanley Dubuis 17-19, rue Jules Berthonneau-BP 3406 41034 Blois Cedex, France. Vertreter in der Union/Représentant dans l’union/Representante en la Union/Rappresentante presso l’Unione Done at/Ort/Fait à/Dado en/Fatto a STANLEY Infrastructure, Portland, Oregon USA...
  • Page 3: Table Of Contents

    REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. For the nearest certified dealer, call STANLEY Infrastructure at (503) 659-5660 and ask for a Customer Service Representative. TP08 User Manual ◄ 3...
  • Page 4: Safety Symbols

    Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and maintenance personnel. 4 ► TP08 User Manual...
  • Page 5: Safety Precautions

    Place the added precautions in the can cause operator discomfort and may cause space provided damage to the tool. The models TP08 Hydraulic Trash Pump will provide • Do not operate a damaged, improperly adjusted or safe and dependable service if operated in accordance incompletely assembled tool.
  • Page 6: Tool Stickers & Tags

    OPERATION MANUAL. OPERATION MANUAL. TAG TO BE REMOVED ONLY BY TAG TO BE REMOVED ONLY BY TOOL OPERATOR. TOOL OPERATOR. SEE OTHER SIDE SEE OTHER SIDE SAFETY TAG P/N 15875 (Shown smaller then actual size) 6 ► TP08 User Manual...
  • Page 7: Hose Types

    This hose is not certifi ed non-conductive and must never be used near electrical conductors. HOSE SAFETY TAGS To help ensure your safety, the following DANGER tags are attached to all hose purchased from STANLEY. DO NOT REMOVE THESE TAGS.
  • Page 8: Hose Recommendations

    HOSE RECOMMENDATIONS 8 ► TP08 User Manual...
  • Page 9: Htma/Ehtma Requirements

    2000 psi 2000 psi (At the power supply outlet) (172 bar) (138 bar) (138 bar) (138 bar) (138 bar) Note: These are general hydraulic system requirements. See tool specifi cation page for tool specifi c requirements. TP08 User Manual ◄ 9...
  • Page 10: Operation

    Observe the following for trash pump hose. For high-pressure water pumping, use a protection and care. STANLEY SM20 or SM50 and nozzle. The TP08 is designed for high GPM water flow at low water The trash pump must maintain a mini mum impeller pressure (head).
  • Page 11 When using recommended fluids, fluid should be at or above 50 °F/10 °C (400 ssu/82 centistokes) before use. Damage to the hydraulic system or pump motor seals can result if the fluid is too viscous or thick. TP08 User Manual ◄ 11...
  • Page 12: Tool Protection & Care

    Do not reverse circuit flow. This can cause damage to internal seals. • Always replace hoses, couplings and other parts with replacement parts recommended by STANLEY. Supply hoses must have a minimum working pressure rating of 2500 psi/172 bar. •...
  • Page 13: Troubleshooting

    Wear plates worn or damaged. Check wear plates for damage and excessive wear. Replace if necessary. Hydraulic fluid in discharge Motor shaft seal failure. Replace the motor shaft seal. Ensure power flow. unit is delivering 7-10 GPM/26-38 LPM TP08 User Manual ◄ 13...
  • Page 14: Specifications

    3. Thoroughly clean the volute and impeller. Do not remove the impeller unless necessary for repair or replace- ment or to remove trapped debris. 4. Re-assemble and clean the capscrews and lubricate the threads with underwater grease before installation. 5. Remove all debris from the hose. Otherwise, solids will backfill the pump. 14 ► TP08 User Manual...
  • Page 15: Tp08 Body Illustration

    Hose (Model TP08013W) 82533 Fitting (Model TP08013W) 82532 Fitting (Model TP08013W) 03976 Male Coupler 03975 Female Coupler 06264 Adapter 07882 Adapter 81261 Cap Screw 81212 Handle 21967 Camlock Coupler 81210 Volute Foot 59074 Cap Screw TP08 User Manual ◄ 15...
  • Page 16: Tp08 Impeller Illustration

    21978 Cap Screw 81133 Spacers 81260 Wear Plate 21989 Cap Screw 21979 Impeller 21989 Cap Screw 81260 Wear Plate 82522 Volute (Yellow) 82523 Volute (Black -Model TP08013B) 59074 Cap Screw 03827 Washer 21988 Acorn Nut 16 ► TP08 User Manual...
  • Page 17: Tp08 Motor Illustration

    Bearing Carrier 21971 Motor Shaft 19793 Bushing 01872 O-ring 20680 Bearing Washer 08020 Thrust Bearing 26812 Retaining Ring 73064 Quad Ring 73059 Seal Carrier 21981 Seal Anvil 01220 Grease Fitting 21976 Housing 10793 Cap Screw TP08 User Manual ◄ 17...
  • Page 18: Underwater Tools Depth Guideline

    ROV operation 3/4” 1” is still limited to the tool, for example a 1” 1” percussive tool has the same depth limitation 1000 1” 1-1/4” whether ROV or diver operated. ► TP08 User Manual...
  • Page 20 STANLEY Infrastructure 6430 SE Lake Road Portland, Oregon 97222 USA (503) 659-5660 / Fax (503) 652-1780 www.stanleyinfrastructure.com...

This manual is also suitable for:

Tp0813Tp08013hTp08013w

Table of Contents