Advertisement
Quick Links
Haas Technical Documentation
Rotary - TR/TRT/T5C - Installation
Rotary - TR/TRT/T5C - Installation - Introduction
This procedure tells you how to install a TR, TRT, or T5C rotary on a Haas VMC. For these instructions, the trunnion axis is the
A Axis (TILT). The platter axis is the B Axis ( ROTARY).
Caution: Make sure the power supplied to the rotary has the correct voltage. Refer to the Machine Compatibility
section before installing a rotary table.
Copyright 2020 by Haas Automation, Inc. No unauthorized reproduction | Last Published On December 13, 2016
AD0005 Rev K
Applies to machines built from:
January, 2007
Scan code to get
the latest version
of this document
Translation
Available
1/12
Advertisement
Related Manuals for Haas TR Series
Summary of Contents for Haas TR Series
- Page 1 Rotary - TR/TRT/T5C - Installation - Introduction This procedure tells you how to install a TR, TRT, or T5C rotary on a Haas VMC. For these instructions, the trunnion axis is the A Axis (TILT). The platter axis is the B Axis ( ROTARY).
- Page 2 Some service procedures can be dangerous or life-threatening. DO NOT attempt a procedure that you do not fully understand. If you have any doubts about doing a procedure contact your Haas Factory Outlet (HFO) and schedule a service visit. Prerequisites Caution: The initial installation of this rotary must be done by a certified Haas Service Technician.
- Page 3 Install cable CABLE, [+12V] ROTARY SCALE FEEDBACK CONTROL END (NGC) (P/N 32-10053). Tools Required Lifting Chain [1] Spreader Beam [2] Lifting Device [3] Dial Indicator [4] Copyright 2020 by Haas Automation, Inc. No unauthorized reproduction | Last Published On December 13, 2016 3/12...
- Page 4 Make sure the TILT Axis is flat to prevent damage to the rotary. If the TILT Axis is not flat, speak to your Haas Factory Outlet (HFO). Copyright 2020 by Haas Automation, Inc. No unauthorized reproduction | Last Published On December 13, 2016 4/12...
- Page 5 In the same location, install the screws that you removed from the shipping bracket. This prevents contamination from coolant in the rotary unit. Do not install the screws you removed from the platter. Copyright 2020 by Haas Automation, Inc. No unauthorized reproduction | Last Published On December 13, 2016 5/12...
- Page 6 For CALM [1] machines, connect the air hose to the machine in the CALM cabinet. For Pre-CALM [2] machines, connect the air hose to the machine below the control cabinet. Copyright 2020 by Haas Automation, Inc. No unauthorized reproduction | Last Published On December 13, 2016 6/12...
- Page 7 If your machine has the Next Generation Control (NGC): 1. Do the Next Generation Control - Rotary - Enable and Disable procedure. 2. Go to step 13. Copyright 2020 by Haas Automation, Inc. No unauthorized reproduction | Last Published On December 13, 2016 7/12...
- Page 8 Manually enter all the B axis parameters using a parameter list. If you do not have a parameter list, speak to your Haas Factory Outlet (HFO). Push [POWER OFF]. Push [POWER ON]. Release [EMERGENCY STOP]. Copyright 2020 by Haas Automation, Inc. No unauthorized reproduction | Last Published On December 13, 2016 8/12...
- Page 9 (+) or negative (-) direction to adjust the flatness. Push ZERO RETURN. Push A. Do this step again until the error is less than 0.0003" (0.008mm). Copyright 2020 by Haas Automation, Inc. No unauthorized reproduction | Last Published On December 13, 2016 9/12...
- Page 10 Lift the rotary table with the lift rings as shown to prevent damage to the gear set. Attach an air supply to the rotary before you lift it. All rotary tables (HRT's, TR's TRT's and T5C's) use the 1/2-13 eyebolts. Haas Automation, Inc. does not supply lifting chains or straps for rotary products.
- Page 11 If spreader bars are not available, eyebolts may be used as shown: Copyright 2020 by Haas Automation, Inc. No unauthorized reproduction | Last Published On December 13, 2016 11/12...
- Page 12 Copyright 2020 by Haas Automation, Inc. No unauthorized reproduction | Last Published On December 13, 2016 12/12...
Need help?
Do you have a question about the TR Series and is the answer not in the manual?
Questions and answers