Advertisement
Available languages
Available languages
Quick Links
INSTRUCTION SHEET
PRODUCT: 64671 XTC2 Tilt • Page 1 of 3
Assembly Instructions
1. Attach the 1-1/4 " receiver bar to the main assembly
using the 12mm x 60mm bolt, washer and nut. Put the
spring clip security lanyard and 3/8" Lynch pin on the
bolt before inserting.
2. Using the 8mm Allen wrench insert and tighten the
folding guide bolt (diagram 1). NOTE: Make sure to
insert the bolt from the proper side. The guide bolt head
fi ts into the slot. Refer to diagram 1.
3. Insert the lynch pin into the hole provide and attached
the spring clip. NOTE: This lynch pin is removed if
folding the bike rack away from the vehicle (diagram 1).
4. Slide the hooks onto the upright portion alternating the
direction (diagram 2).
5. Unfold the two side arms as shown (diagram 2) and
insert 2 lynch pins. Ensure that the pins are all the way
in. Slide the hooks onto the upright portion alternating
the direction
6. Slide the 4 wheel holder trays on to the bottom arms
alternating the direction of the trays (diagram 3). Do
not tighten them at this time, as they will have to be
adjusted to fi t each bike that you are carrying.
7. After the wheel holders are installed you will need to
screw in the 2 metal screws at the end of each arm. This
will prevent wheel holders from coming off (diagram 4).
8. Take the bike rack and install into the vehicle hitch.
Install the threaded pin and clip and tighten to
50 ft. lbs. (tight).
9. If the rack is to be used on 1-1/4" receiver you will need
to remove the Allen Bolt that hold on the spacers. Use
the 6mm Allen Wrench (diagram 5).
Installing the Rack Into Your Vehicle:
1. Insert the bike rack into the 2" or 1-1/4 " receiver. Install
the ½" threaded locking hitch pin and tighten to 50 ft
lbs. (very tight). Put on the lock head until it is securely
attached.
2. The rack is designed to carry up to two 35 lbs. bikes. You
cannot combine weight to carry one bike over 35 lbs.
300 - 1880 Government St. • Penticton, B.C. Canada V2A 7J1 • Phone (250) 490-8883 • Fax (250) 490-8885 • www.swagman.net
Parts List
1/2" Threaded
12mm x 60mm
Hitch Pin
Hitch
Pin Clip
Self Taping
Screws
3/8" Lynch Pin
with Spring
Clip
8mm
Allen Keys
Guide Bolt
1
LYNCH PIN WITH
SPRING CLIP
REV 23/10/19
Advertisement
Related Manuals for Swagman 64671 XTC2 Tilt
Summary of Contents for Swagman 64671 XTC2 Tilt
- Page 1 2. The rack is designed to carry up to two 35 lbs. bikes. You cannot combine weight to carry one bike over 35 lbs. REV 23/10/19 300 - 1880 Government St. • Penticton, B.C. Canada V2A 7J1 • Phone (250) 490-8883 • Fax (250) 490-8885 • www.swagman.net...
-
Page 2: Bike Installation
Due to the increase in thinner/lighter “carbon frame bikes” this rack may be inappropriate because the hook clamps the frame. Please check with your bike manufacturer for specific details. REV 23/10/19 300 - 1880 Government St. • Penticton, B.C. Canada V2A 7J1 • Phone (250) 490-8883 • Fax (250) 490-8885 • www.swagman.net... -
Page 3: Important Notes
The rack is not under warranty if mounted in this location. ATTN: STATE OF CALIFORNIA CONSUMERS WARNING: Cancer and Reproductive Harm • www.P65Warnings.ca.gov REV 23/10/19 300 - 1880 Government St. • Penticton, B.C. Canada V2A 7J1 • Phone (250) 490-8883 • Fax (250) 490-8885 • www.swagman.net... - Page 4 1,25 po. Insérez la tige fi letée de 1/2 po puis serrez très fermement jusqu’à 50 pi/lb. Insérez la goupille de blocage jusqu’à ce qu’elle bien fi xée. REV 15/05/19 300 - 1880 Government St. • Penticton, B.C. Canada V2A 7J1 • Phone (250) 490-8883 • Fax (250) 490-8885 • www.swagman.net...
- Page 5 Veuillez vérifier auprès du fabricant de vélo pour plus de détails. REV 15/05/19 300 - 1880 Government St. • Penticton, B.C. Canada V2A 7J1 • Phone (250) 490-8883 • Fax (250) 490-8885 • www.swagman.net...
-
Page 6: Remarques Importantes
Le porte-vélos n’est pas couvert par la garantie s’il est monté à cet endroit. REV 15/05/19 300 - 1880 Government St. • Penticton, B.C. Canada V2A 7J1 • Phone (250) 490-8883 • Fax (250) 490-8885 • www.swagman.net...