Olympia AD220 User Manual

Olympia AD220
Cree® XP-G LED
Flashlight
User Guide
Congratulations on your purchase of the
Olympia AD220 Cree® XP-G LED high-
performance flashlight. This product is designed
to provide you with the best possible functionality.
The AD220 utilizes Cree
is geared for optimum brightness and efficiency.
It's constructed in aircraft-grade aluminum with
premium Type II hard anodized, anti-abrasive
finish. The lightweight, compact design makes
it a functional light for multiple uses including
hunting, hiking, camping, caving, general
household use, recreational activities, rugged Head
sports or emergency situations. Please take a
few moments to read this user guide to ensure
that you get the best performance and years of
trouble-free service.
Product Description
Head
Head
Battery Installation
1. Unscrew the tail switch cap and insert
2xCR123 (non-rechargeable / 1x16340
(rechargeable) *batteries. The (+) terminal on
the batteries should face toward the flashlight's
head.
2. Replace the tail switch cap and be sure to
tighten snugly, but do not over tighten as this
could strip the threads in the cap. Turn on the
flashlight as indicated in any of the options
listed in the table that follows. Note: If the tail
Head
Head
cap is not tightened snugly; the flashlight
Body
Head
will not turn on.
3. When the battery life is nearly depleted, your
flashlight will blink to indicate new batteries are
needed.
Head
Body
Head
*Non-rechargeable batteries included
Flashlight Operation
Your Olympia AD220 Cree® XP-G LED high-
performance flashlight has a push-button tail
switch for on/off operation and is equipped with
1) Momentary and 2) Continuous light options.
It also has 5 light modes to suit your varied
needs. See table instructions to access these
functionalities:
LED technology that
®
Tail
Clip
Cap
Body
Clip
Tail
Clip
Cap
Body
Body
Clip
Tail
Clip
Cap
Tail
Clip
Switch
Cap
Switch
Body
Body
Lanyard
Hole
Lanyard
Hole
Clip
Clip
Body
Momentary-on
Continuous
Lighting Modes
Switch
Lanyard
Hole
Memory function
Tail
Cap Your Olympia AD220 Cree® XP-G LED flashlight
Switch
automatically memorizes the last light setting/
mode used when the flashlight next is turned
on. i.e., after being in any one of the five light
Switch
settings (HighMiddleLowStrobeSOS) for
3 seconds, the last one used will be memorized.
Lanyard
Hole
Maintenance and Precautions
Lanyard
Hole
1. Do not disassemble the sealed head. Doing
so can cause damage to the flashlight and will
void the warranty.
2. Use high-quality batteries or you run the risk
of the flashlight being damaged by electrolyte
Tail
leakage or battery breakage.
Cap
3. If the flashlight will not be used for a long time,
Switch
remove the batteries to avoid damage caused
from battery leakage.
4. Lubricate the O-rings regularly using a
Q-tip
or petroleum jelly to the contacts to prevent
Lanyard
Hole
corrosion. Doing so will keep the flashlight
properly sealed against water. If the O-rings are
damaged after prolonged use, replace them.
5. Clean the flashlight contacts periodically
especially if the light flickers or does not light
Tail
up. There are different reasons for a flickering or
Cap
Tail
non-working light:
Switch
Cap
A: The batteries may need to be replaced.
Switch
Lanyard B: The threads, PCB board contact or other
Hole
Lanyard
Hole
If the above methods do not work, please refer to
the warranty policy listed in this user guide.
!
The AD220 is a high-intensity lighting device and
capable of causing eye damage. Please avoid
shining the light directly into the eyes.
Lighting Operation Modes
Press the push-button tail switch
half-way to activate the light
Lighting
Press the tail switch push-button to
completely turn on the flashlight.
Lighting
The light will stay on until the push-
There are five types of light output:
Press the tail push-button to switch
Accessing the 5 Lighting Modes
Press the push-button tail
High Beam
Press the push-button tail
Mid Beam
Press the push-button tail
Low Beam
Press the push-button tail
Strobe
Press the push-button tail
SOS
. Apply a small dab of silicone grease
®
Solution: Replace old/defective batteries with
new ones (be sure to double check correct
installation of + and - terminals).
contacts are dirty.
Solution: Use a Q-tip
of alcohol to clean the contact points.
Warning
momentarily.
button is turned off.
HighMiddle
LowStrobeSOS
to each mode
switch once
switch twice
switch 3 times
switch 4 times
switch 5 times
to apply a tiny amount
®