Olympia AD220 Cree XPG LED User Manual

Olympia AD220
Cree XPG LED
Flashlight
User Guide
Congratulations
Olympia AD220 Cree XPG LED high-performance
flashlight. This product is designed to provide you
with the best possible functionality. The AD220
utilizes Cree LED technology that is geared for
®
optimum brightness and efficiency. It's constructed
in aircraft-grade aluminum with premium Type II
hard anodized, anti-abrasive finish. The lightweight,
compact design makes it a functional light for
multiple uses including hunting, hiking, camping,
caving, general
activities, rugged sports or emergency situations. Head
Please take a few moments to read this user guide
to ensure that you get the best performance and
years of trouble-free service.
Product Description
Head
Head
Battery Installation
1. Unscrew the tail switch cap and insert
2xCR123 (NiMH) rechargeable *batteries. The
(+) terminal on the batteries should face toward
the flashlight's head.
2. Replace the tail switch cap and be sure to
tighten snugly, but do not over tighten as this
could strip the threads in the cap. Turn on the
flashlight as indicated in any of the options
listed in the table that follows. Note: If the tail
Head
cap is not tightened snugly; the flashlight
Body
Head
Head
will not turn on.
3. When the battery life is nearly depleted, your
flashlight will blink to indicate new batteries are
needed.
Head
Body
Head
*batteries included
Flashlight Operation
Your Olympia AD220 Cree XPG LED high-
performance flashlight has a push-button tail
switch for on/off operation and is equipped with
1) Momentary and 2) Continuous light options.
It also has 5 light modes to suit your varied
needs. See table instructions to access these
functionalities:
on your purchase
Tail
Clip
Cap
household use, recreational
Body
Clip
Tail
Clip
Cap
Body
Body
Tail
Clip
Cap
Clip
Tail
Clip
Switch
Cap
Switch
Body
Lanyard
Hole
Body
Lanyard
Hole
Clip
Clip
Body
Momentary-on
Continuous
Lighting Modes
of the
Switch
Lanyard
Hole
Memory function
Tail
Cap Your Olympia AD220 Cree XPG LED flashlight
Switch
automatically memorizes the last light setting/
mode used when the flashlight next is turned
Switch
on. i.e., after being in any one of the five light
settings (HighMiddleLowStrobeSOS) for
3 seconds, the last one used will be memorized.
Lanyard
Hole
Maintenance and Precautions
Lanyard
Hole
1. Do not disassemble the sealed head. Doing
so can cause damage to the flashlight and will
void the warranty.
2. Use high-quality batteries or you run the risk
Tail
of the flashlight being damaged by electrolyte
Cap
leakage or battery breakage.
Switch
3. If the flashlight will not be used for a long time,
remove the batteries to avoid damage caused
from battery leakage.
4. Lubricate the O-rings regularly using a
Q-tip
Lanyard
Hole
or petroleum jelly to the contacts to prevent
corrosion. Doing so will keep the flashlight
properly sealed against water. If the O-rings are
damaged after prolonged use, replace them.
Tail
5. Clean the flashlight contacts periodically
Cap
Tail
especially if the light flickers or does not light
Switch
Cap
Switch up. There are different reasons for a flickering or
non-working light:
A: The batteries may need to be replaced.
Lanyard
Hole
Lanyard
Hole
B: The threads, PCB board contact or other
If the above methods do not work, please refer to
the warranty policy listed in this user guide.
!
The AD220 is a high-intensity lighting device and
capable of causing eye damage. Please avoid
shining the light directly into the eyes.
Lighting Operation Modes
Press the push-button tail switch
half-way to activate the light
Lighting
Press the tail switch push-button to
completely turn on the flashlight.
Lighting
The light will stay on until the push-
There are five types of light output:
Press the tail push-button to switch
Accessing the 5 Lighting Modes
Press the push-button tail
High Beam
Press the push-button tail
Mid Beam
Press the push-button tail
Low Beam
Press the push-button tail
Strobe
Press the push-button tail
SOS
. Apply a small dab of silicone grease
®
Solution: Replace old/defective batteries with
new ones (be sure to double check correct
installation of + and - terminals).
contacts are dirty.
Solution: Use a Q-tip
of alcohol to clean the contact points.
Warning
momentarily.
button is turned off.
HighMiddle
LowStrobeSOS
to each mode
switch once
switch twice
switch 3 times
switch 4 times
switch 5 times
to apply a tiny amount
®