Table of Contents
Advertisement
Quick Links
ANSI Z359.18
2104560
x1
2104568
x1
2100041
x0
2100066
x0
B
A
C
OSHA 1926.502
Type A
OSHA 1910.140
AnSI
x1
x1
x1
x10
D
ConCrete Bolt
Anchorage Connector
USER INSTRUCTIONS
1
oSHA
A
4.44 in.
(11.28 cm)
(2.77 cm)
4.44 in.
(11.28 cm)
(2.77 cm)
4.44 in.
(11.28 cm)
4.44 in.
(11.28 cm)
5902288 R
. E
Ev
B
C
1.09 in.
3.02 in.
(7.67 cm)
1.09 in.
3.02 in.
(7.67 cm)
---
---
---
---
D
5.83 in.
(14.81 cm)
5.83 in.
(14.81 cm)
---
---
© 3M 2020
Advertisement
Table of Contents
Related Manuals for 3M DBI-SALA 2104560
Summary of Contents for 3M DBI-SALA 2104560
- Page 1 2104560 (11.28 cm) (2.77 cm) (7.67 cm) (14.81 cm) 4.44 in. 1.09 in. 3.02 in. 5.83 in. 2104568 (11.28 cm) (2.77 cm) (7.67 cm) (14.81 cm) 4.44 in. 2100041 (11.28 cm) 4.44 in. 2100066 (11.28 cm) © 3M 2020...
- Page 3 18 mm, 11/16 in., 3/4 in. 4 1/8 in. (10.5 cm) ≥15.0 in. (38.1 cm) ≥6.25 in. (15.9 cm) ≥10.0 in. (25.4 cm) ≥4.13 in. (10.5 cm) =18mm, 11/16 in., 3/4 in. ≥3000 psi (20.7 MPa)
- Page 4 2104560 2104568 INSTALLATION: Hole Depth: 4 1/8 in. Step 1: Mark location for anchor. Observe minimum edge Hole Diameter (d): 11/16 in., 18mm, or 3/4 distance and spacing requirements. See reverse side of label for additional requirements. Min.
-
Page 5: Safety Information
Ensure there is adequate fall clearance when working at height. Never modify or alter your fall protection equipment. Only 3M or parties authorized in writing by 3M may make repairs to the equipment. Prior to use of fall protection equipment, ensure a rescue plan is in place which allows for prompt rescue if a fall incident occurs. -
Page 6: Product Description
Prior to installation and use of this equipment, record the product identification information from the ID label in the Inspection and Maintenance Log (Table 2) at the back of this manual. Always ensure you are using the latest revision of your 3M instruction manual. Visit the 3M website or contact 3M Technical Services for updated instruction manuals. -
Page 7: Product Application
PRODUCT APPLICATION PURPOSE: Anchorage Connectors are designed to provide anchorage connection points for Fall Arrest , Fall Restraint Work Positioning , or Rescue systems. Fall Protection Only: This Anchorage Connector is for connection of Fall Protection equipment. Do not connect Lifting Equipment to the Anchorage Connector. - Page 8 3M connectors (snap hooks and carabiners) are designed to be used only as specified in each product’s user’s instructions. See Figure 6 for examples of inappropriate connections. Do not connect snap hooks and carabiners: To a D-ring to which another connector is attached.
-
Page 9: Installation
INSTALLATION The owner of this equipment may contact 3M Technical Services with any questions regarding equipment installation, use, or inspection. Installation of the DBI-SALA Concrete Bolt Anchor must be performed or supervised by a Competent Person for Non- Certified Anchorages. A Qualified Person shall supervise the design, selection, installation, use, and inspection of Certified Anchorages. -
Page 10: Maintenance, Service, And Storage
DEFECTS: If the Concrete Bolt Anchor cannot be returned to service because of an existing defect or unsafe condition, or because it has been subjected to a fall arrest, either destroy the product or contact 3M regarding possible replacement or repair. - Page 11 Table 2 – Inspection and Maintenance Log Inspection Date: Inspected By: Competent Components: Inspection: User Person (See Section 1 for Inspection Frequency) Concrete Bolt Anchor Inspect the Concrete Bolt Anchor for damage: Inspect the torque seal. If (Figure 2) the green seal on the bolt head is damaged or missing, the Concrete Bolt Anchor may not be properly installed or may have been tampered with.
- Page 12 LIMITED REMEDY: Upon written notice to 3M, 3M will repair or replace any product determined by 3M to have a factory defect in workmanship or materials. 3M reserves the right to require product be returned to its facility for evaluation of warranty claims. This warranty does not cover product damage due to wear, abuse, misuse, damage in transit, failure to maintain the product or other damage beyond 3M’s control.