Advertisement
With Mounting Bracket Kit for Adjustable Installation
Model Number
Kennedy II 42 / JR-42S EF-WM502
Kennedy II 50 / JR-50S EF-WM503
Kennedy II 60 / JR-60S EF-WM504
Kennedy II 72 / JR-72S EF-WM505
Carefully read and review before assembling, installing, operating, or maintaining
this product. Observe all safety instructions and information.
For customer service & warranty issues, please contact:
08.19.20
Item Number
Page 1
Advertisement
Table of Contents
Related Manuals for Kennedy Kennedy II 42 / JR-42S
Summary of Contents for Kennedy Kennedy II 42 / JR-42S
- Page 1 With Mounting Bracket Kit for Adjustable Installation Model Number Item Number Kennedy II 42 / JR-42S EF-WM502 Kennedy II 50 / JR-50S EF-WM503 Kennedy II 60 / JR-60S EF-WM504 Kennedy II 72 / JR-72S EF-WM505 Carefully read and review before assembling, installing, operating, or maintaining this product.
- Page 2 • Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance according to operating instructions could cause fire or injury. • Risk of burns. Power should be turned off and the appliance allowed to cool down before servicing. To disconnect power, turn controls to off, then remove plug from outlet.
-
Page 3: Side View
Dimensions SIDE VIEW FRONT VIEW BOTTOM VIEW Listing Approvals electric room appliances in the United States and Canada. If you need assistance during installation, please contact your local dealer. NOTE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition in the United States or the Canadian Electric Code, CSA C22.2 in Canada. - Page 4 READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING INSTALLATION. FAILURE TO FOLLOW THEM COULD CAUSE AN APPLIANCE MALFUNCTION RESULTING IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. ALL ELECTRIC APPLIANCES HAVE HOT AND ARCING OR SPARKING PARTS INSIDE. DO NOT USE IT IN AREAS WHERE GASOLINE, PAINT OR FLAMMABLE LIQUIDS ARE PRESENT. THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE OPTIONAL ACCESSORIES LISTED IN THESE INSTRUCTIONS.
- Page 5 JR-42S JR-42S JR-42S x1 JR-42S JR-50S JR-50S JR-50S JR-50S JR-60S JR-60S JR-60S JR-60S JR-72S JR-72S JR-72S JR-72S JR-42S x1 JR-42S x1 Bags JR-42S x5 JR-50S x1 Bags JR-50S JR-50S JR-60S JR-60S x1 Bags JR-60S x5 JR-72S JR-72S x1 Bags JR-72S x10 Download the JR App Available for Android and iOS, the JR app can be used to control your WiFi-enabled fireplaces.
- Page 6 DUE TO HIGH TEMPERATURES, THIS ELECTRIC APPLIANCE SHOULD BE LOCATED OUT OF TRAFFIC. KEEP COMBUSTIBLE MATERIALS SUCH AS FURNITURE, PILLOWS, BEDDING, PAPERS, CLOTHES AND CURTAINS AT LEAST 36” (914mm) FROM THE FRONT OF THE APPLIANCE. NEVER LOCATE THIS ELECTRIC APPLIANCE WHERE IT MAY FALL INTO A BATHTUB OR OTHER WATER CONTAINER.
- Page 7 RISK OF FIRE! THE POWER CORD MUST NOT BE PINCHED AGAINST A SHARP EDGE. SECURE CORD TO AVOID TRIPPING OR SNAGGING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY. DO NOT RUN CORD UNDER CARPETING. DO NOT COVER CORD WITH THROW RUGS, RUNNERS OR THE LIKE.
- Page 8 FIG. 1 FIG. 2 SIDE VIEW FRONT VIEW - Easy installation - Exchangeable trim - Front maintenance - Front maintenance For installation For installation instructions refer instructions refer to Page 9 to Page 11 Page 8 08.19.20...
- Page 9 Option 1: Hanging the Appliance on the Wall Due to the many different materials used on different walls, it is highly recommended that you consult your local builder before you install this appliance on the wall. 1. Select a location that is not prone to moisture and is located at least 36” (914mm) away from combustible materials such as curtain drapes, furniture, bedding, paper, etc.
-
Page 10: Top View
Option 2: Recessing the Appliance Flush into the Wall builder before you install this appliance in the wall. Select a location that is not prone to moisture and is located at least 36” (914mm) away from combustible materials such as curtain drapes, furniture, bedding, paper etc. 1. - Page 11 Sides, back and top 0” TOP VIEW Stud Wall (NON-LOAD BEARING) EF-WM502 EF-WM503 EF-WM504 EF-WM505 A’, B’, and C’ are the suggested opening dimensions for installing the firebox into the frame wall. Dimensions are subject to the constructor’s final confirmation. Page 11 08.19.20...
- Page 12 TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE. If it is necessary to hard wire this appliance, a qualified electrician must remove the cord connection, and wire the appliance directly to the house hold wiring.
- Page 13 TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE. Wall Thermostat Wiring (24AWG) 1. Turn off circuit breaker. 2. Remove cover plate located on the left side of the appliance. 3.
-
Page 14: Front Glass Removal
Front Glass Removal 1. Remove 4 screws on both sides. Remove front glass and place it in a secure location FIGURE 4 Crystal Embers and Wood Logs Installation embers are installed. 1. Complete steps 1-2 in the “ Front Glass Removal” instructions. 2. - Page 15 WHILE THE APPLIANCE IS OPERATING DO NOT REMOVE THE GLASS PANEL. THIS WILL CAUSE THE REMOTE CONTROL TO DISFUNCTION. Once the appliance has been plugged into a grounded electrical outlet, it is ready to operate. To turn unit power on: 1.
- Page 16 WiFi APP Installation Procedure Available for Android and iOS, the Smart Flame Connect app can be used to control your WiFi-enabled fireplaces. After installing the app follow these steps: 1. Create an Account HOME Create a profile to use the JR App, and connect your fireplace for convenient control: Ensure you have access to an email.
- Page 17 Multi-functional Operating with Remote Control Turning ON/OFF the appliance: Ensure steps 1-2 in the"Main Power Switch"procedure are first followed. ” remote button to turn on the red, blue and yellow flame at the brightest 2. Press the “ level.Ember bed color is white. Indicate “ON” on LED display. The heater is in OFF status.
-
Page 18: Remote Control Specification
Remote Control Specification 1.Model: R302 2. Remote Key: 12 3. Communication: Infrared 4.Infrared Distance: 6 Meters 5. Battery: AA x 2pcs NOTE: Make sure your “AA” batteries (x2) are fully charged and installed correctly in your remote control before operating. The remote control must remain within 6 meters of the appliance to be effective, this range may be reduced when battery power is... - Page 19 Wiring Diagram: Standard Model WARNING TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE. RECEIVER TOUCH KEY TEMP SENSOR ADPTER 120V TRAN.-I MOOD1 T-IN TEMP1 MOOD2 WIFI MODULE FAN-N1 FAN-N2 MOOD3...
-
Page 20: Replacement Parts
Replacement Parts WARNING FAILURE TO POSITION THE PARTS IN ACCORDANCE WITH THIS MANUAL OR FAILURE TO USE ONLY PARTS SPECIFICALLY APPROVED WITH THIS APPLIANCE MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. To order parts, contact customercare@jrhome.com FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE ORIGINAL INVOICE WILL BE REQUIRED TO HONOUR THE CLAIM. -
Page 21: Replacement Parts Diagram
Replacement Parts Diagram WARNING FAILURE TO POSITION THE PARTS IN ACCORDANCE WITH THIS MANUAL OR FAILURE TO USE ONLY PARTS SPECIFICALLY APPROVED WITH THIS APPLIANCE MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. NOTE: Care must be taken when removing and disposing of any broken glass or damaged components. Be sure to vacuum up any broken glass from inside the appliance before operation. - Page 22 TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE. Symptom Potential Cause Solution Abnormal noise From heater assembly (item 7) Blower assembly has a defect that is causing noise during high speed rotation.
-
Page 23: Troubleshooting
Troubleshooting Symptom Potential Cause Solution Dim or no flame / Flame LED’s are burnt out or Inspect the LED’s and replace them if Ember bed / Ceiling wire loosing necessary light is not glowing or Ember bed LED’s are burnt out Inspect the LED’s and replace them if dimming or wire loosing... -
Page 24: Warranty
IMPORTANT For questions, concerns or problems with our product please Si vous éprouvez des dicultés, ou si vous avez des questions ou des email our customer service department: préoccupations, prière de faire parvenir un courriel à notre Service à la clientèle customercare@jrhome.com customercare@jrhome.com DATED PROOF OF PURCHASE REQUIRED FOR WARRANTY SERVICE...