—— Instruction Manual ——
S
O
C
HOOT
UT
OMBO
B
ISON
P A R T S L I S T
Item
Qty
Description
A
4
Crossbar
B
2
Inner Tube
C
2
Connecting Bar
D
6
Football Crossbar Support Bracket
E
8
3/8" x 1" Hex Bolt
F
12
5/16" x 1" Carriage Bolt
♦
Inspect all contents prior to installation. Report any missing parts to dealer immediately.
♦
Read all instructions before proceeding.
1. Assemble Soccer Goal per separate instructions provided.
2. Unpack and lay out two Crossbars (A), one Inner Tube (B), and one Connecting Bar (C) on a flat surface.
Slide the Connecting Bar (C) into the Inner Tube (B) through the channel so that all the holes are lined up.
Insert the Inner Tube (B) into one of the Crossbars (A) leaving half of the Inner Tube (B) exposed. Install
two 3/8" x 1" Hex Bolts (E) loosely. Insert another Crossbar (A) onto the exposed half of the Inner
Tube (B). In the farthest exposed hole loosely install one 3/8" x 1" Hex Bolt (E). See Figure 1.
3. Insert the head of a 5/16" x 1" Carriage Bolt (F) into the net attachment track and slide over the joint where
the Crossbars (A) meet. Install the 3/8" x 1" Hex Bolt (E) and tighten all 3/8" x 1" Hex Bolts (E).
See Figure 1.
4. From each end of the Crossbar (A) insert and slide the head of a 5/16" x 1" Carriage Bolts (F) approximately
17-5/16" from the end.
5. Lay the soccer goal assembly down in position directly below the Crossbar (A) with the net attachment track
facing upward. On the soccer goal temporarily remove one of the 3/8" x 1" Hex Bolts (E). Insert the heads
of three 5/16" x 1" Carriage Bolts (F). Slide the 5/16" x 1" Carriage Bolts (F) approximately 21-5/16" in
measuring from the outside of the soccer goals upright. The middle one should be centered. Reinstall and
tighten the 3/8" x 1" Hex Bolt (E) in the soccer goals crossbar. See Figure 2.
6. Place the Football Crossbar Support Brackets (D) over the 5/16" x 1" Carriage Bolts (F). Using the 5/16"
Flat Washer (G), and 5/16" Nylon Lock Nuts (H) tighten the Football Crossbar Support Brackets (D) to the
crossbars.
7. Using the pilot holes provided in the Football Crossbar Support Brackets (D) drill a 5/16" hole through the
bottom of the Football Crossbar Support Brackets (D) and through one wall of the crossbars. Using the
3/8" x 1" Thread Cutting Hex Bolts (I) to fasten the Football Crossbar Support Brackets (D) to the upper and
lower crossbars (48 places). NOTICE! Use care when tightening the 3/8" x 1" Thread Cutting Hex Bolts (I).
Do not over tighten! See Figures 2 and 3.
Date:
10/16/2013
A
F
LUMINUM
OOTBALL
M
: SC2480IGAFB,
ODEL
Rev: 1
B.A.
S
G
OCCER
SC2480PA44FB
OR
Item
Qty
Description
G
12
5/16" Flat Washer
H
12
5/16" Nylon Lock Nut
I
64
3/8" x 1" Thread Cutting Hex Bolts
J
4
10' Upright
K
4
Upright Support
N.J.C.
File:
\publisher\instructions\SC2480AFB
1
K
OAL
IT
Customer Service
(800) 247-7668
Ref#: 860166